pressure viscosity 中文意思是什麼
pressure viscosity
解釋
受壓粘度-
Abstract : the formation technologies, the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied. the results indicate that the rheological behaviour and spinnability of commixed polyester melt, and the structure and properties of the fibre, are relative to the spinning temperature, melt pressure, microporpus size for spinning, formation conditions, thermo - vascellum temperature, thermo - vascellum position and rolling speed, besides the viscosity of polyester cuts, coacervation particles, adding amount and size of micrometallic - oxide
研究表明， tcs微孔化共混聚酯熔體在成型加工中的流變行為和可紡性，及其纖維的結構性能除了與原料切片的特性粘度、凝聚粒子和共混聚酯中超細金屬氧化物微粒的添加量、粒徑等因素的影響有關外，還與紡絲溫度、紡絲熔體壓力、噴絲板微孔尺寸、冷卻成形條件、熱管溫度、熱管安裝位置以及卷繞速度等因素的影響密切有關。 -
Changes of the longitudinal and transversal wave velocities in different directions and the rock velocity anisotropy as a function of confining pressure have been studied under laboratory ultrasonic frequency for shale and sandstone with marked foliation, which had been saturated by the fluids with different viscosity kerosene and vacuum pump oil and salinity distilled water, 50000
利用不同黏度煤油和真空泵油不同礦化度蒸餾水50mg l和150mg l的nacl溶液的流體對頁巖和具有明顯層理的砂巖進行飽和，在實驗室超聲頻率下研究樣品不同方向縱橫波速度以及各向異性參數 -
Complete air piston pump contains pneumatic motor and piston pump, the ratio of piston area of pneumatic motor and plunger ' s sectional area of piston pump is transforming times of pump pressure ; the higher times, the more pressure can deliver higher viscosity fluid, and achieve the delivery aim
完整的氣動柱塞泵包含有氣動馬達與柱塞泵兩部分，氣動馬達中的活塞面積與柱塞泵活塞的截面積比值，就是泵壓力轉換的倍數；愈高的倍數就能以愈大的壓力輸送愈高黏度的流體，達到輸送的目標。 -
Air piston pump adopts the theory that " pressure " applying force on various areas and can produce various " acting force ", the pump takes the origin that the compressed air is compressed energy, and transforms the pressure of compressed air into more fluid pressure, pressing fluid move in order to achieve the aim of high viscosity and ultra - viscosity fluid
氣動柱塞泵是利用「壓力」在不同的面積上施力，產生不同「作用壓力」的原理，以壓縮空氣為壓力能量的來源，將壓縮空氣的壓力轉換成更大的流體壓力，壓迫流體移動，進而達到輸送高黏度及超高黏度流體的目的。 -
The article aims at meeting a successful weaving of pure cotton fine count and high density satin fabric on new - type air jet loom by using better sizing compatibility of pva, modified starch and acrylic size based adopting processing route of high - pressure & high - concentration & low - viscosity to improve sizing permeability and coverage, increase abrasion - proof, reduce hairiness and to clear shedding
摘要利用pva 、變性澱粉、丙烯漿料各組分之間良好的溶性，採用「兩高一低」上漿工藝路線，以改善漿紗的浸透與被覆增加耐磨，貼伏毛羽，提高開口清晰度，來滿足純棉高支高密貢緞織物在新型噴氣織機上的織造要求。 -
The boundary layer can indicate the comprehensive influences of oil reservoirs, the physical properties ( reservoir porosity, permeability, fluid viscosity and its composition ) of inside fluids and development conditions such as pressure gradient : the layer thickness reduces with the rise of capillary radius ; when capillary radius is fixed, the thickness increases with viscosity rise ; the more polarity composition content is, the more obvious the absorption, the thicker the boundary layer, more and more obvious the characteristics of non - darcy filtration
邊界層反映了儲層、流體物性條件（儲層孔隙度、滲透率、流體粘度、組分）和開發條件（壓力梯度）的綜合影響，認為邊界層厚度隨著毛管半徑的增大而減小；在毛管半徑相同的情況下，邊界層厚度隨壓力梯度的增大而減小，最後達到一個臨界值；毛管半徑一定時，邊界層厚度隨粘度增加而增大；極性組分含量越大，吸附越明顯，邊界層厚度越大；邊界層厚度越大，非達西滲流特徵越明顯。 -
Increasing the temperature in the zones of the final half of the extruder will generally result in lower viscosity and pressure
提高壓出機後半部分區域的溫度一般可以增大粘度和提高壓力。 -
In this paper the experimental research of hydra ulic oil used on a certain composite gearbox are carried on the experimental fo rm ulas are drawn respectively between viscosity 、 density 、 specific heat and temper ature the function of viscosity to temperature and pressure is deduced the com parative analysis among the new oil 、 used oil and ordinary antifriction oil ind icates the performance of the specitic oil is excellent these conclusions are b eneficial to the advanced analysis of the vehicle transmission system and formul ate the manual of relevant armored caterpillar
該文對某軍用履帶裝甲車輛綜合傳動系統使用的液壓油進行了試驗分析，得出了這種液壓油的粘度、密度、比熱與溫度的經驗關系式，推導出了粘度在溫度、壓力綜合作用下的函數關系，並對新油、舊油、普通抗磨液壓油的粘度進行了對比分析，這對于使用這種液壓油的傳動系的分析計算和制定相關軍用履帶裝甲車輛的使用規范提供了重要的理論依據 -
Abstract : in this paper the experimental research of hydra ulic oil used on a certain composite gearbox are carried on the experimental fo rm ulas are drawn respectively between viscosity 、 density 、 specific heat and temper ature the function of viscosity to temperature and pressure is deduced the com parative analysis among the new oil 、 used oil and ordinary antifriction oil ind icates the performance of the specitic oil is excellent these conclusions are b eneficial to the advanced analysis of the vehicle transmission system and formul ate the manual of relevant armored caterpillar
文摘:該文對某軍用履帶裝甲車輛綜合傳動系統使用的液壓油進行了試驗分析，得出了這種液壓油的粘度、密度、比熱與溫度的經驗關系式，推導出了粘度在溫度、壓力綜合作用下的函數關系，並對新油、舊油、普通抗磨液壓油的粘度進行了對比分析，這對于使用這種液壓油的傳動系的分析計算和制定相關軍用履帶裝甲車輛的使用規范提供了重要的理論依據 -
In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards
論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。 -
The results demonstrate that the bubble velocity will increase with the increasing of the bubble volume, decreasing of resin viscosity and external pressure
此外，樹脂種類和樹脂流動狀態對氣泡的運動速度也有較大的影響。 -
This product is collod feathering achro, aticity and viscosity, wghhich can clear the thick oxideatice horizon hot pressed end plate or rollsteel plank which be processed or welded under hot temperature and hot pressure
本產品為無色透明的粘稠狀膠體，針對不銹鋼熱壓封頭或用熱軋板製作工件等，經過高溫高壓處理或焊接時所產生紅、黑、黃等各種類型的較厚氧化層，清除迅速，徹底。 -
Instantaneous pressure variations and spikes are due to large instantaneous changes in melt viscosity
瞬間的壓力變化及峰值出現是由熔融粘度瞬間變化導致的。 -
Then, the one dimensional model is used to study on some factors ( viscosity, the heat given out by the chemical reaction in the chemical laser ) which bring the loss of the total pressure. the answer shows that increasing the mach number at out of the nozzles in the laser can reduce the loss of the total pressure
在此基礎上，用簡化的一維模型研究了引起激光器總壓損失的幾個要素，它們是:噴管的粘性損失，光腔內的放熱化學反應。研究的結果表明，提高噴管出口馬赫數有利於減少這些因素導致的總壓損失。 -
The result indicates that displacement characteristics of unsheared polymer solution is better than the same viscosity polymer solution after sheared, the injection pressure of the unsheared polymer solution is higher than the same viscosity polymer solution after being sheared in the same permeability core, the lower the permeability, the bigger the molecule weight and the bigger the difference, as to the every layer of the secondary oil layer, it is feasible to displace oil with the polymer solution after sheared, and the eor of the polymer flooding can increase more than 9. 84 %
結果表明：未經剪切的聚合物溶液的驅油效果好於經剪切之後的相同相對分子質量的聚合物溶液的驅油效果；對于相同滲透率的巖心，未經剪切的聚合物溶液比經過剪切相同相對分子質量聚合物溶液的注入壓力高，而且滲透率越低，相對分子質量越大，差異越大；對於二類油層的各滲透率小層，進行經剪切后聚合物溶液驅油是可行的，聚驅采出程度提高幅度均超過9 . 84 % 。 -
Through large amount of lab experiments, the relation of oil boundary layer thickness with capillary radius, pressure gradient, fluid viscosity and its composition has been discussed
摘要通過大量的室內實驗，探討了原油邊界層厚度與毛管半徑、壓力梯度、流體粘度和組分的關系。 -
In this article, constituting some the equations which reflect the flow law and building and applying many mathematical models of physical and chemical reactions in the the plasma ignition : applying k - two equations turbulence model to calculate the turbulence parameter supplying simplied reaction systerm model and applying eddy break - up model and p - i thermal radiation model. with these reasonable simplied modles, numerically simulating the flow field in the plasma ignition. during the numerical simulation, applying the body - fitted coordinates for the complex geometry of the computional field ; using the mixing format to disperse the equations ; applying simplec algorithm method to solve the equations ; using above models and methods, it can get flow field distribution ; including temperature, pressure, turbulent kinetic energy and its dissipation rate, turbulent viscosity, velocity, density. these results are significant to design and improve the plasma ignition
本文旨在通過構造反映等離子點火器內部流動規律的基本方程組，建立描述等離子點火器內部的復雜物理化學過程機制數學模型：模擬等離子發生器內部燃燒的-雙方程湍流流動模型；模擬氣體燃料在燃燒時中化學反應的簡單化學反應系統模型；模擬等離子點火器內部湍流預混燃燒的漩渦破碎模型；模擬等離子點火器高溫燃氣及其壁面的p - i輻射換熱的模型等等，對模型進行一定的合理的簡化，然後數值模擬等離子點火器內部流場的流動。 -
The domestic artificial map cracking ( cavity ) core is first presented, which is accordant with prerequisites similar to the real permeability and the percolation spatial configuration of the reservoir, and successfully applied to the long - core test under the conditions of high pressure, high temperature, high salinity and high viscosity available
在國內首次人工製造出了同時符合油藏儲滲層滲流空間形態要求和滲透率要求的網狀裂縫（洞）巖心，並在四高，即壓力高、溫度高、礦化度高、粘度高的模擬油藏實際條件下成功應用人工製造網狀縫巖心完成了輪古地區長巖心驅替實驗。 -
The results from basic properties, shear resistance, pressure strength and point film test show that different low molecular polyamide may affect extrodinary by the properties of cured expoxy resin the higher viscosity, the lower cured activity ( rate ) ; the higher amine number, the stronger cure construction. the cured expoxy resin will prossess unfavourable mechanics when it is cured by the polyamide with both too high viscosity and amine number
用基本性能、剪切強度、抗壓強度、塗膜性能測定等方法研究了3種不同胺值及粘度的低分子量聚酰胺對環氧樹脂固化物性能的影響.結果表明，聚酰胺粘度大使固化交聯變難，胺值過高易造成固化收縮；同時粘度過大、游離胺含量過高的產品將對固化物各項力學性能不利 -
Temperature, pressure, liposome composition, drug stability, ionic strength, and viscosity all may have stabilizing or destabilizing effects ( manifested as unacceptable shelf life )
溫度、壓力、微脂粒成分、藥物穩定性、離子強度、粘度，這些因素都將影響效果是否穩定和壽命的長短。
分享友人