pressure volume temperature 中文意思是什麼
pressure volume temperature
解釋
壓力一體積一溫度- pressure : n 1 壓；按；擠；榨。2 【物理學】壓力，壓強；大氣壓力；電壓。3 精神壓力，政治[經濟、輿論等]壓力。4...
- volume : n. 1. 卷，冊；書籍；【歷史】書卷，卷軸。2. 〈常 pl. 〉大塊，大量，許多。3. 體積；容積；分量，額；【物、樂】音量；強度，響度。
- temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
-
The pressure of a gas is ( directly ) proportional to its absolute temperature when its volume remains constant
當氣體體積保持不變時，氣體壓力就和其絕對溫度成正比。 -
According to this law, the pressure of a given mass of gas at constant temperature is in inverse proportion to the volume occupied by the sea
根據這個定律，在恆定溫度下，某定量氣體的壓力是和該氣體所佔的體積成反比的。 -
Modbus transducer is the key device in the system and is used to offer power supply of pressure and temperature sensor, to collect signal, to linearizate and compensate temperature, to calculate density, volume and mass, to transmit data to modbus network, and display the data. so the modbus transducer is a multi - parament measurement, intelligent control device which can manage multi - signal
變送器是系統的核心設備，其作用是為油罐溫度、壓力、液位、可燃氣濃度等傳感器供電，採集傳感器信號並進行線性化、溫度補償等處理，完成密度、體積和質量等參數計算，將數據輸出到modbus現場總線測控網路，根據需要現場顯示計測量參數。 -
Pvt. plastics - determination of specific volume as a function of temperature and pressure pvt diagram - piston apparatus method
塑料.作為溫度和壓力函數的比容的測定 -
This diaphragm avoids a pressure rise in the case that is due to temperature bound volume expansion of the liquid filling, thus avoiding indicated errors
當溫度突升造成填充液體膨脹時，膜片可以避免壓力升高，從而避免指示錯誤。 -
This diaphragm avoids a pressure rise in the case that is due to the temperature bound volume expansion of the liquid filling, thus avoiding indicated errors
當溫度突升造成填充液體膨脹時，膜片可以避免壓力升高，從而避免指示錯誤。 -
This paper establishes a model simulating dam actual placing process and considering the non - continuity of initial temperature on the boundary of new and old concrete, daily air temperature change, concrete - placing temperature, hydration heat, heat insulation on boundary, water - storing process, placing intermission and curing with water. the calculation of stress field considers the concrete weight, static water pressure, thermal stress, different autogenous volume change between rcc and normal concrete, change of elastic modulus of concrete with age and creep action
考慮了乞今最為全面的初始條件和邊界條件，包括模擬壩體的實際升程過程，考慮了新老混凝土接觸面上的初始溫度不連續，逐日的氣溫變化，混凝土的入倉溫度，水化熱溫升，邊界保溫，水庫蓄水過程，澆築間歇以及灑水養生等因素；應力場的計算考慮了混凝土的自重，靜水壓力，溫度應力，常態混凝土與碾壓混凝土不同的自生體積變形，混凝土的彈性模量隨齡期的變化以及徐變的作用。 -
When we keep the temperature constant, the volume of a gas changes inversely with the pressure
當我們使溫度保持恆定時，氣體的體積與壓力成反比。 -
The pressure of a gas is inversely proportional to its volume, if its temperature is kept constant
如果溫度保持不變，則氣體壓力和其體積成反比。 -
To get mass flow rate of vent gas and coarse aeetaldehyde from their volume flow rate data, density compensations are performed with regressed relationship between density and ( temperature, pressure and concentration )
針對包含化學反應過程的生產流程，提出了基於原子衡算的數據調和演算法，並將之應用於乙醛生產過程的數據調和。調和計算中考慮了粗乙醛流量和小放空氣體流量的密度補償。 -
Temperature kits : contact must be properly fixed in the evaporator export pipelines, real - time communication evaporator components to temperature degrees, the material will be filled through interlinked capillary pressure due to the expansion of corrugated boxes ; swelling corrugated boxes on the pressure for change in the thrust pole with an adjustment screw and spring - loaded ball - type valves to adjust the resistance of the degrees of refrigeration volume precision adjustments
感溫包：是必須妥善接觸固定在蒸發器的出口管道上，感知蒸發器實時回氣溫度的部件，它將充填物質的熱脹冷縮壓力通過相通的毛細管提供給膨脹波紋箱；膨脹波紋箱依據壓力的變化推動推力桿結合過熱度調整螺絲和彈簧的阻力來調整球型閥的開度，實現製冷量的精確調整。 -
Narrowly speaking, eos is the relationship between the pressure, the volume and temperature of substance system in thermodynamic equilibrium
從狹義上來講，物態方程是描述處于熱力學平衡態的物質系統中壓強、溫度、體積之間的函數關系。 -
In a narrow sense of the word, equation of state ( eos ) is the relationship of pressure, volume ( or density ) and temperature ( p - v - t ) for substance system in thermodynamic equilibrium
從狹義上講，物態方程是描述處于熱力學平衡態的物質系統中壓強、溫度、體積或密度之間的函數關系（ p - v - t ） 。 -
The parameters mean the evaporation capacity or the volume, pressure, and temperature
介質參數是指蒸發量或容積、壓力、溫度。 -
Eight of input and state variables of blast furnace, i. e. silicon content, irregular coke charge, coal injection, blast pressure, blast temperature, blast volume, batch of charge in a tapping period, ratio of ore - to - coke in charge, are considered as input of prediction model
採用天津鐵廠1 #高爐的[ si ]含量、鐵間料批數、熱風壓力、實際噴煤量、冷風流量、熱風溫度、凈焦加入量、焦炭負荷等8個影響因素作為預測模型的主要輸入變量。 -
Equation of state ( eos ) for porous iron is used to describe the relationship of its state variables : volume, temperature and pressure in equilibrium states, which is used widely in the geography
物態方程是指描述平衡態物質系統的壓強、體積和溫度三個熱力學變量關系的等式。研究多孔鐵的沖擊壓縮物態方程在地學領域有廣泛的應用。 -
It is very difficult to analyze flame radiation in the cylinder of a diesel engine by theoretical method since flame radiation is a function of many parameters, such as the combustion process, the geometrical description of the chamber, the soot formation and oxidation processes, the soot radiant temperature and soot absorption coefficient. the radiant property of the flame in a cylinder is dependent on the combustion process. but the thermodynamic state of real engine cycles can be analyzed from the pressure - volume diagrams in the cylinder. thus a new thermodynamic computational model is set up for the flame radiation in the cylinder of a diesel engine based on the indirect relationship between the flame radiation and the pressure - volume diagram of the combustion process in this paper. the flame radiant heat flux in the cylinder of a di diesel engine is calculated with the variation of crank angle by this model. compared with measured values, the result of the computational values shows the model is available to represent the effects of flame radiation
柴油機缸內的火焰輻射受諸多因素的影響，用理論分析法來確定它是相當困難的，由於柴油機缸內火焰輻射特性依賴于缸內的燃燒過程，而燃燒過程中的實際熱力狀態又可用示功圖來分析，因此藉助於火焰輻射與缸內熱力參數之間的這種間接關系，建立了一種計算柴油機缸內火焰輻射傳熱的新模型，利用該模型對一臺直噴柴油機缸內火焰輻射熱流量隨曲軸轉角的變化情況進行了計算，將計算結果與實測結果進行了比較，表明該模型能較好預測缸內火焰輻射傳熱量。 -
Three valve units that volume is small, weight is light, structure is simple, strong and durable, parts exchangeability is good. fpr temperature, static pressure variation and impulse the whole device have reliable stability, apply for 1151, 3051, fc, k, cfc, sbcc every series differential pressure transmitter : flow transmitter products coordinate usage, can be installed on the product and with product form integratization, has simplified product installation structure
三閥組體積小重量輕結構簡單堅固耐用，零部件互換性好，整體裝置對溫度和靜壓變化及沖擊有可靠的穩定性，適用於1151 3051 fc k cfc sbcc等各系列差壓變送器，流量變送器產品配套使用，可直接安裝在產品上，與產品成一體化，簡化了產品的安裝結構。 -
Three valve manifold that volume is small, weight is light, structure is simple, strong and durable, parts exchangeability is good. for temperature, static pressure variation and impulse the whole device have reliable stability, apply for 1151, 3051, fc, k, cfc, sbcc every series differential pressure transmitter : flow transmitter products coordinate usage, can be installed on the product and with product form integratization, has simplified product installation structure
體積小重量輕結構簡單堅固耐用，零部件互換性好，整體裝置對溫度和靜壓變化及沖擊有可靠的穩定性，適用於1151 3051 fc k cfc sbcc等各系列差壓變送器，流量變送器產品配套使用，可直接安裝在產品上，與產品成一體化，簡化了產品的安裝結構。 -
Abstract : the forced state in key parts and their lifetime, the volume of high pressure chamber and ratio of pressure, the length of high pressure stroke and pressure stability, the relations between the deformation of high pressure chamber and temperature field and pressure field for three kinds of apparatus of making synthetic diamond under high pressure and high temperature were compared in this paper. the differences of these main apparatus were analyzed according to the degree of difficulty and ease in the technique, the choice of applicability and the cost and yield of them. it was emphasized that studying and developing the large sized belt - type press should be the way to make high quality saw diamond and change the state of making middle and low quality diamond in the diamond industry of our country, catching up with the international advanced level as well
文摘:通過對高溫高壓合成金剛石3種主要裝備在關鍵部件受力狀況與使用壽命、高壓腔體積與壓力利用率、高壓沖程大小與壓力穩定性，高壓腔變形與溫場、壓場的關系等方面的比較，分析了3種主要裝備在技術難易程度、適用性選擇和投入產出比的差異；強調了我國金剛石行業要改變當前只能生產中低檔金剛石的現狀，向生產高品級鋸片級金剛石的方向發展，與國際接軌，應該走大型化兩面頂的道路。
分享友人