producing thickness 中文意思是什麼
producing thickness
解釋
生產厚度-
Area in which combustible dust, as a cloud, is present continuously or frequently, during normal operation, in sufficient quantity to be capable of producing an explosive concentration of combustible dust in mixture with air and / or where layers of dust of uncontrollable and excessive thickness can be formed
在正常運行過程中可燃性粉塵連續出現或經常出現，其數量足以形成可燃性粉塵與空氣混合物和或可能形成無法控制和極厚的粉塵層的場所及容器內部。 -
To solve the problem of the fear of inadequacy of armor protection on the already heavily armored kv - 1 model 1941, it was decided to bring the armor protection of the turret up to a thickness to 75mm. since the capability of producing such a thick armor plate was lacking at the time, so an interim solution was to use bolt on armor, 25 mm of thickness, bolt directly to the outside of the turret and some other parts of the hull. this type was usually referred to as kv - 1s ehkranami
針對kv - 1 1941年型的裝甲防護能力不足的問題，設計人員進行了一系列強化裝甲的工作，改進后的kv - 1的炮塔裝甲達到了大約75毫米的厚度但在具體製造中由於為kv坦克提供裝甲鋼板的工廠沒有能力生產必要厚度的裝甲鋼板，因此，作為臨時解決方案用螺栓在車體和炮塔上加裝了25毫米厚的附加裝甲，這種改進的kv坦克被命名為kv - 1附加裝甲型。 -
Pilot - scale experimental results showed that, comparing to conventional gravity filtration, the up - flow filtration has greater capacity in containing removed suspended solid and producing filtrate under the test conditions. coarse media with particle diameter ranging 0. 63 - 2. 00mm were used in order to apply relatively higher backwash rate of 21 l / ( m2. s ) for achieving better media clean - up after a filtration run. under the test conditions, the media thickness ranging 82 - 85 iron, water temperature ranging 6 - 27, and influx turbidity of 30 ntu, it achieved the results of the average filtration rate ranging 16 - 18 m / h, the average effluent turbidity of 1 ntu, and action cycle ranging 14 - 24h
中試研究結果表明，粗石英砂濾料上向流過濾比傳統的重力流過濾具有更大的含污能力和產水量，為適用較高的反沖洗強度（ 21l （ m ~ 2 ? s ） ）以便濾料清洗更干凈，採用粒徑范圍為0 . 63 2 . 00mm的粗石英砂濾料，濾層厚82 85cm ，水溫6 27 ，進水濁度為30ntu左右等情況下，能獲得平均濾速為16 18m h 、平均濾后水濁度為1ntu左右、周期達14 24小時的好效果。 -
The structure and the thickness of the coatings was inspected by the xjp - 2 metallography microscope, the structure morphology was tested by philips xl30 peg sem, and the adhesion between the foundation and the coating was examed by two methods : one is ws - 92 sound - producing coating adhesion nick testing, another is bending
利用xjp - 2型金相顯微鏡觀察鍍層組織並測其厚度， philipsxl30feg型掃描電鏡觀測鍍層表面的組織形貌，鍍層與基體的結合力採用ws - 92型聲發塗層附著力劃痕試驗和彎折法兩種方法來定性地檢測。 -
Upon author ' s long distance experience in producing aluminum easy open can, he had studied and researched deeply many kind of easy open cans in the worlds, analyzed the technique of key several production program of can making and solved a series of key technical problems during the process of light - weighting such as, aluminum raw material, can profile design, press technique and mould design etc. after carrying out light - weighting, the used aluminum raw material thickness of easy open can ' s body could be thinned from 0. 325mm to 0. 285mm, the weight of gram per can could be reduced from 13. 625g to 11. 948g, its economic benefit could be more big obviously
本文在對國內外輕量化技術的應用現狀進行深入分析的基礎上，從技術層面對易拉罐輕量化實施過程中的若干關鍵性問題進行了探討。通過對國內外各種罐型所進行的深入研究，從易拉罐製造過程中關鍵工序的工藝分析入手，解決了輕量化實施過程中罐用材料、罐型設計、沖壓工藝、模具設計等一系列關鍵技術難題。輕量化技術成功實施后，易拉罐罐體所用鋁材厚度從0 . 325mm減少到0 . 285mm ，單罐克重從13 . 625g降低到11 . 948g ，取得了明顯的經濟效益。 -
Based nit the definition of production decline rate, the multifactor analytical model for composite decline rate is developed, which discusses affecting factors stub as the startup well number, water cut, producing fluid thickness, pressure, relative production index well spacing density, skin factor etc
摘要從產量遞減率定義出發，首先導出了綜合遞減率與開井數、含水、產液厚度、壓力、相對產液指數、井網密度、表皮系數等多因素分析模型。 -
Thus the irregularity index is analyzed. the method this paper discussed is an innovatory of the universal thickness measurement. three research results will help filling in a gap in this field and provide the basis for the study of mechanical capacity and producing the three - dimensional braided composite materials perform accurately
本文所研究的碳纖維三維編織復合材料預製件的測厚方法是對常規的測厚方法的一次突破，該系統的研製成功，為三維編織復合材料測量增加了一種新的測量設備，為復合材料的力學性能研究和正確製造碳纖維三維編織復合材料預製件提供了必要的基礎。 -
Standard practices for producing films of uniform thickness of paint, varnish, and related products on test panels
色漆，清漆，噴漆及有關產品製成厚度均勻漆膜試片的標準實施規程
分享友人