pulse circuit 中文意思是什麼
pulse circuit
解釋
脈沖電路-
A circuit topology of the inverter with duty cycle extended active clamp forward style high frequency pulse dc link is adopted by each independent inverter. each inverter is cascaded by a circuit with duty cycle extended active clamp forward style high frequency pulse dc link and a dc / ac inverting bridge. the control strategy of voltage mode pwm forwardback is adopted by the former, and the control strategy of three - state discrete pulse modulation ( dpm ) hystersis current is adopted by the later
每個獨立的航空靜止變流器採用占空比擴展有源箝位正激式高頻脈沖直流環節電路拓撲，由占空比擴展有源箝位正激式高頻脈沖直流環節電路與dc ac逆變橋級聯而成，前級採用電壓型pwm前饋控制技術，后級採用三態dpm電流滯環控制技術。 -
This paper presents a method that chopping wave is done by switch devices which consist of three - level resistance regulating module and intelligence power module ipm, and which realizes constant - current discharge of storage battery. to achieve the intelligence control of the drive protection and the discharge process of ipm, the paper designs circuit formed by igbt threshold drive pulse pwm signals. ipm fault - blocking protection circuit and microcomputer 80c196. the devices can accurately control the 0 ~ 150a discharge current and the discharge time of the storage battery and calculate the releasing power
實現蓄電池恆流放電過程智能控制是蓄電池放電裝置發展的必然趨，本文提出了一種通過三極電阻調節模塊和由智能功率模塊ipm為開關器件進行斬波從而實現蓄電池恆流放電的方法。為達到對ipm的驅動保護和放電過程的智能控制，文中設計了igbt門極驅動脈沖pwm信號形成電路和ipm故障封鎖保護電路及由單片機80c196為核心的微機控制器。本裝置能夠對蓄電池進行0 150a放電電流及放電時間的精確控制及釋放容量的計算。 -
In the sub block circuit design, the contents that the author had introduced include : the principle of band gap voltage reference and the design technique in low power supply ; the analysis of spike pulse noise rejection, frequency divider and dead time in oscillator and control circuit ; the selection of the width and length ratio of four switches and 2x / 1x mode change point in driver and mode selection circuits
在子電路設計中，作者比較深入分析的內容有:基準電路的原理及低電源電壓下基準電路的設計;振蕩器和控制電路中尖峰脈沖噪聲抑制、兩分頻電路及死區時間設定;驅動及模式選擇電路中開關管的寬長比的選擇及模式轉換點的設計。 -
Incondition of surface anti - corrision and insulation coat of metal and tiny hole of steel where resistance and crack is very small, when supplying a high voltage, gas crack will be punctured and electric spark discharging will occur, now send a pulse signal to the alarming circuit the alarmer can send out sound and light to alarm. we can do leak hunting on the coating according to this principle
金屬表面絕緣防腐層過薄、漏鐵及漏電微孔處的電阻值和氣隙密度都很小，當有高壓經過時就形成氣隙擊穿而產生火花放電，給報警電路產生一個脈沖信號，報警器發出聲光報警，根據這一原理達到防腐層檢漏目的。 -
Research on double pwm pulse mig feed - wire circuit based on c8051f
焊送絲電路的研究 -
At the same time the principles of triggering pulse to the three - phase thyristors is discussed, and a way using monostable multivibrator to produce the pulses has been given below. the hardware control system based on tms320f240 is designed, which includes sampling circuit, protective circuit, phase - compensated circuit and so on
對三相晶閘管控制電抗器的觸發脈沖產生原理進行了分析，採用單穩態觸發器實現六相觸發同步；設計了以tms320f240為控制核心的硬體控制平臺，包括采樣電路、保護電路、六相觸發同步等外圍電路。 -
At the same time the effection of some important recombinations are discussed and the relation of photoconduction versus time is given. in chapter 4, auston circuit, blumlein pulse forming line, multiplier of pulse forming line are introduced and give their differentiates
在第四章中，分析各種以光導開關為核心器件的電脈沖成形電路: auston電路、 blumlein脈沖成形線、層疊線倍壓器，對其輸出轉換效率進行比較，並進行實驗研究。 -
This paper starts the research of the liquid floated pendulous accelerometer testing system according to the engineering. at first, this paper gives the brief introduction of the history and present status of accelerometer and its testing technology, the working principium and math model of the liquid floated pendu - lous accelerometer, and then, decides the binary width pulse force retrim loop as the design proposal of testing system, researches the transfer function of every part in the system emphasizly, analyses the stability of the whole accelerometer testing system from the angle of control theoretics by the open loop transfer function of system, and designed the correcting net, analyses the basal problems such as resolution, sampling restraint, precision and so on, designs the hardware testing circuits such as preamplification, band - pass filter, alternating amplifier, phase sensitive demodulatorn, pulse - width modulation, frequency scale circuit, moment current generator. finally, using the graphics program language labv - iew which is designed for testing field especially by ni accomplishes the solfware design of testing system, realized the testing functions
首先對加速度計及其測試技術的發展歷史和現狀，液浮擺式加速度計的工作原理和數學模型等作了簡要的介紹，然後確定了以二元調寬脈沖再平衡測試迴路為設計方案，並從控制理論的角度進行了分析，著重研究了系統中各部分的傳遞函數，利用系統開環傳遞函數分析了系統的穩定性，同時設計了系統的校正網路;分析了二元調寬脈沖再平衡測試迴路的解析度、采樣約束以及測試精度等基本問題，並按照系統分析的結果設計了包括前置放大、帶通濾波、交流放大、相敏解調、脈寬調制、頻標電路以及力矩電流發生器等測試系統各部分硬體電路，驗證了電路的正確性，最後按照測試系統的要求，採用了美國ni公司專為測試領域所開發的虛擬儀器工具? ? labview作為測試軟體開發工具，利用該圖形化編程語言完成了測試系統軟體部分的設計，實現了測試功能。 -
2 、 metal halide lights start more difficult than other types of high - intensity gas discharge lights. the work circuit of the metal halide lights and the lc series resonance start controller are analyzed, and its shortcomings are noted. through the relations of breakdown voltage ? time, the thesis discusses a quick - start controller using pulse transformer
2 .金屬鹵化物燈的啟動問題較其它類型的高強度氣體放電燈更為困難，作者對金屬鹵化物燈的工作電路進行了理論分析，對目前常用的lc串聯諧振啟動方式進行了較為詳細的理論研究，並指出了其存在的缺點。 -
In the paper, on the basis of research of static state and transient state in the scr and series connection valve circuit, the high voltage scr changing current valve device has been developed for ac - dc - ac high voltage commutatorless motor. the series connection valve circuit has been designed and simulated. the hardware design and software programming of trigger pulse system and monitoring system in the photo - electronic - photo fashion has been completed
無換向器電動機在火電廠等工礦企業的電機調速節能領域中有十分廣闊的應用前景，本文在對晶閘管元件和串聯閥電路的靜態特性和動態特性研究的基礎上，研製了用於交直交電流型高壓無換向器電動機的高壓晶閘管換流閥裝置，進行了串聯閥電路的設計和模擬，完成了電光電方式的觸發脈沖系統和監測系統硬體設計及軟體編程，並進行了裝置的實驗調試。 -
Second, the results of theory analysis and simulation research show that the output of one cycle controlled bridge switching power amplifier have dc offset because of the nonideal characteristic of reset signal. the magnitude of output dc offset voltage is proportional to width of reset pulse. a voltage compensation technique is used to solve this question, and the computation formula of compensation voltage is gived. the circuit compensated and not are researched through simulation and experiment, which results show that compensated circuit solve the output dc offset effectively
其次，理論分析和模擬研究結果表明，由於復位脈沖的非理想特性，單周控制的全橋開關功率放大器輸出端存在直流偏置問題，其大小與復位脈沖的寬度成正比。針對輸出直流偏置問題，提出了電壓補償的改進方案，給出了補償電壓的具體計算公式。對補償前和補償后的方案進行了對比模擬研究和實驗研究。 -
In the experimental system apd transferred laser pulse to weak electrical current. after two - level amplification we got a voltage pulse that had a enough amplitude to be applied, the timing point was discriminated by the constant - fraction timing discriminator circuit. timing circuits transferred the pulse flight time to digital signal accurately
實驗系統採用apd作為光電傳感器，將激光脈沖信號轉變為微弱電流脈沖，經過兩級放大后，信號變為幅度較大的電壓脈沖，經過時點鑒別電路分別確定計時起點和終點后，由計時電路來精確測量兩個時間點之間的時間間隔。 -
The technology of alternating - current - boosting by way of constant current is successfully used to charge capacitors with 25 kilojoules of energy in only eight seconds. rail - gap switch with performances of long life and highly steady state are designed. and the high voltage pulse generator, which can produce low - excursion and fast - rise pulses, are designed by using double trigger circuit and hydro - thyristor as switch
在大功率恆流充電技術上，成功的應用了交流調壓式恆流技術，可以在8s內讓電容器儲存25kj的能量;設計出了長壽命、高穩定的軌道開關;採用氫閘流管做開關，使用雙觸發電路，研製出了低抖動、快前沿的高壓脈沖發生器（點火機） ;採用單片機和pld ，研製出了精度為10ns的延時同步機。 -
Synchronous pulse generating circuit : got by back panel output 1pps 、 1ppm 、 1pph synchronous pulse signal. pulse is photoelectric isolation static idle contact form output
同步脈沖發生電路：通過後面板輸出秒（ 1pps ） 、分（ 1ppm ） 、時（ 1pph ）同步脈沖信號。脈沖是光電隔離的靜態空接點形式輸出。 -
The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance
通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。 -
Adjusting digital potentiometer in controlling circuits of sps and capacitor charging and discharging circuit separately with industry control computer ( icc ), the peak value and repeat frequency of output pulse can be adjusted separately. controlling relays to choose different capacitors with icc, the width of output pulse can be adjusted
利用工控機分別調節開關式穩壓電源控制電路和電容充放電控制電路中的數字電位器，就能分別調節輸出陡脈沖的幅值和重復頻率；利用工控機控制繼電器選擇不同的充放電電容，就能調節輸出陡脈沖的脈寬。 -
The structure, function and characteristic with the principle and method of tank gauging system are described. then the structure, principle of the circuit and the main chips of the data processing unit are introduced. after this, the software design of data processing unit including rs - 485 ( modbus ) module, 4 - 20ma analog module, on - off module, rtd module, pulse module, calculation and display module, communication module and neuron chip program module and also the method of resolving the problems which were found at the process of debugging are emphasized
隨后介紹了現場數據處理器的結構，電路原理，所運用的主要晶元；並重點闡述了作者在課題研究中所作的工作，即現場數據處理器軟體的設計包括八個功能模塊： rs - 485 （ modbus ）模塊、 4 ? 20ma模擬量採集模塊、開關量處理模塊、 rtd信號採集模塊、頻率量採集模塊、計算和顯示模塊、通訊模塊、 neuron晶元中的程序模塊；以及在課題研究和現場調試過程中遇到的問題及解決辦法。 -
Clock pulse circuit
時鐘脈沖電路 -
These results prove that the charging action of the power supply is right. the simulation method is applied with other power supply system. at the same time, the hardware system of 2qkv - 60kw high - voltage capacitor direct current charging power supply is described in this paper, and discuss why designed a full digital phase - shifting pulse circuit
同時，本文敘述了20kv ? 60kw高壓電容直流充電電源的硬體電路的設計，其中討論了為什麼不採用已有的uc3875 、 uc3879等晶元來產生zvspwmdc dc變換器的移相脈沖，設計了全數字式移相脈沖產生電路。 -
The test system including power circuit, restoration circuit, pulse circuit, the circuit of the memory ( sram and flash ), jtag interface circuit, the control circuit of the touch - panel, lcd interface circuit
該測試系統的功能模塊包括電源電路，復位電路，晶振電路，存儲器電路（ sram和flash ） ， jtag介面電路，觸摸屏控制電路， lcd介面電路。
分享友人