push-push amplifier 中文意思是什麼
push-push amplifier
解釋
推-推放大器-
Experiment result proved, relative to complicated structure and hig h request for laying wiring of zvs series resonant full - bridges, push - pull class - e amplifier is expected more suited for high frequency high - power output ability relatively, which is suitable for popularizing
實驗證明，相對于結構復雜，布線要求較高的全橋串聯諧振逆變器，推挽式雙e類放大器具有更高頻率和較大功率的輸出能力，適于推廣一。 -
Catv push - pull amplifier module
Catv推挽放大系列模塊 -
Push - pull amplifier
推挽放大器 -
I will use single ended examples, followed by an illustration of how this is also applied to push - pull amplifier stages
我會以單端輸出為例，並在文章最後說明如何把它們應用到推挽電路。 -
The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。 -
550mhz and 750mhz push - pull amplifier module designed by our company recently are one of the best choice for trunk amplifier in tv system
我公司新推出的550mhz ， 750mhz推挽放大模塊是有線電視系列干線放大器首選模塊之一。 -
The experiment verified the validity that push - pull class - e amplifier is more suitable for high frequency high - power inverter
通過實驗對比，推挽式雙e類放大器更適合高頻大功率的開發研製。 -
Grounding on above theory, the zvs resonant of soft switch full - bridges circuit, and class - e amplifier, and push - pull class - e amplifier are analyzed respectively in theory. push - pull class - e amplifier is available by comparing results of simulation and low power experiment
基於以上理論，分別選擇了zvs諧振型全橋串聯逆變器、 e類放大器以及推挽式e類放大器進行詳細的理論分析，模擬比較以及小功率實驗對照。 -
Firmly push the amplifier ( expansion unit ) all the way into the main unit
一直緊緊的推擠放大器（擴展模塊）進入主模塊。 -
Based on the design theory of power amplifier, a wide - band power amplifier was designed successfully by the push - pull transistor, the feedforward technical of linearization, the matching circuits of transmission line transformers and microstrip, and ads simulation software
根據寬帶功率放大器的設計原理，採用推挽結構晶體管，前饋線性化技術，傳輸線變壓器和微帶混和匹配電路，利用ads進行模擬設計，成功的設計出一款寬帶功率放大器。
分享友人