r-max 中文意思是什麼

r-max 解釋
合金戰紀
  • r : 1 〈拉丁語〉 recipe 【醫學】處方。2 radical 3 Reaumur 4 〈拉丁語〉 Rex Regina 5 radius 6 ratio 7 ...
  • max : n. 馬克斯〈男子名， Maximilian 的昵稱〉。n. ＝maximum. to the max 最大限度地，徹底地。vt. ，vi. 〈max out〉（使）絞盡腦汁；（使）竭盡全力。
  1. 2 there is also a new result on two bipartite graphs. let h be a graph obtained from km and kn by joining them with a bridge, and m > n > a > b, then r ( kab, h ) < max { r ( ka ? km ), r ( ka4, kn ) + m }

    另外對完全二部圖的ramsey數進行研究，給山一個結論： h是在k _ m和k _ n之間連接一個橋得到的， m n b 。
  2. Based on analyses of about 600 coal - seam samples used for " classification of chinese coal ", the range of mean maximum reflectance of vitrinite ( r ( superscript o subscript max ), % ) of different classes of bituminous coal was presented and the correspondence between them was discussed

    摘要運用制定《中國煤炭分類》國家標準所依據的近600個煙煤煤層煤樣實測數據，分析了中國不同煤種煙煤鏡質組平均最大反射率的分佈范圍，探討了煙煤鏡質組平均最大反射率與中國煤分類系統之間的關系。
  3. As news of the cheap fuel spread, lines formed at the store at 2305 r st., said max wolfe, who was doing landscaping for kabredlo ' s

    負責該便利店景觀美化工作的麥克斯沃爾夫表示，這里有廉價汽油出售的消息迅速傳遍四方，紛至沓來的人們在店外排起了長龍。
  4. In this dissertation, the effect of texture, heat - treatment, and hydrogen on the lcf behavior of zircaloy - 4 and the cyclic deformation behavior for zircaloy - 4, n18 alloy and n36 alloy have been investigated systematically using fully - reversed tension - compression loading under strain control ( r = min / max = - 1 ), while the evolvement of the friction and back stresses versus the number of repeated working cycles and the plastic strain amplitude has been studied, and the thorough discussion combined with the analysis result of fatigue sub - structure, friction and back stresses, and fatigue fracture has been given to the mechanism underlying the lcf behavior of alloys

    本文採用對稱拉壓循環變形方法（ r _ = _ （ min ） _ （ max ） = - 1 ） ，系統研究了織構、熱處理狀態、氫對zr - 4合金低周疲勞性能的影響， zr - 4合金、 n18合金和n36合金的循環變形行為，並研究了摩擦應力、背應力隨循環周次、塑性應變幅的變化規律。結合疲勞亞結構和疲勞斷口的分析結果，深入探討了影響合金低周疲勞行為的作用機制。
  5. Main results : theorem 1 let e be a real banach space, p be a normal cone in e. conditions ( a1 ) - ( a3 ) be satisfied, let k0 < c2, and l = max { 1, maxj g ( t, s ) }, inequality 4l # [ c3 + m + 47 # k0 ( c4 + 2n ) ] < 1 holds. then there exist monotone sequences { vn ( t ) }, ( wn ( t ) }, such that uniformly on i and p ( t ], r ( t ) are minimal and maximal solutions between vq and w0 forpbvp ( 1. 1 )

    （ a2 ）存在常數m o ， n 0 ，滿足這里（ a3 ）對和等度連續的有界單調序列都有其中本文的主要定理：定理設為實空間， p是中正規錐，條件滿足，設設滿足則存在單調序列在上一致成立，且分別為上的最小解和最大解
  6. First we give some notations : where r lti : the load of the machine at step t ( i. e., immediately after the ith job has been scheduled ) optt : the current optimum makespan in step t ( for the job set { j1 ; …, jt } ) lbt : the lower bound of the length in step t for a set of jobs with processing times p1, …, pn, there are three straightforward lower bounds for the makespan of any preemptive schedule on m identical machines : max so we have lb = max ( 3. 2. 1 ) the algorithm will schedule jobs in such a way that, at any step t algorithm : a new job jt + 1 ( which arrives at time t + 1 ) is assigned as follows : step 1 compute the new lower bound lbi + 1 according to ( 3. 2. 1 ) step 2 research the following reserved intervals

    需加工n個工件人； … ；人，每個工件是在線到達（ oneb ， olle ）且可打斷的，機器人人的準備時間為az ，怎樣安排加工順序，使工件的最大完工時間（ makespan ）盡可能地小，稱此問題為帶機器準備時間的平行機在線排序問題。它是帶機器準備時間的平行機排序和平行機在線排序問題的綜合和推廣；具有廣泛的應用背景。這里工件在線到達（ onebyone ）指的是工件的情況並不是提前知道的，只有將工件jj人安排完以後我們才能知道工jj的一些情況p工件的加工時間p 。
分享友人
分享到 Line

分享到臉書