radial angle 中文意思是什麼
radial angle
解釋
徑向角-
By comparing the results with relative experiment data, it is shown that rng k - is more exactly than the other turbulent model. 2 ) the influences of axial inflow position, radial outflow size, rotating reynold number, non - dimensional mass flowrate and axial inflow angle on the flow and heat transfer characteristics were numerically investigated for a typical rotator - stator cavity with axial inflow, radial inflow and radial outflow. the correlations for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established
（ 2 ）針對一典型的徑向、軸向進氣，徑向出氣的轉-靜盤腔結構，系統研究軸向進氣位置、徑向出口大小、旋轉雷諾數、無量綱質量流量和軸向垂直預旋進氣等對盤腔內流動和換熱的影響，整理出轉-靜盤腔內轉盤平均努謝爾數與旋轉雷諾數無量綱質量流量之間的準則關聯式。 -
Time complexity analysis of two non - angle algorithms to determine the radial spatial adjacent relationship
確定射線空間相鄰關系的兩個非角度演算法的時間復雜度分析 -
Angle contact ball bearing can be subject to both radial and axial load, it also can be subject to pure axial load, its axial load capacity is depend on the contact angle and increased accordingly. it can be used for high speed and high precision application dueto high limit speed and pre - adjustable rigidity
角接觸球軸承可同時承受徑向載荷和軸向載荷，也可以承受純軸向載荷，其軸向載荷能力由接觸角決定，並隨接觸角增大而增大，且極限轉速較高，剛性大還可預調，適用於高速、高精度場合。 -
The utility model belongs to the material processing machinery, which comprises mountings, bearings, gears, revolving axles, cutting tools, radial adjusting devices, and angle adjusting devices etc
它包括機架、軸承、齒輪、回轉軸、刀具、徑向調整裝置、角度調整裝置等。 -
Effects of different fuel - air ratios and different geometric parameters of dual - stage swirler ( such as inner diameters of the primary swirl and secondary swirl passages, outer diameters of the secondary swirl passages, vane angle of the primary and secondary swirler, the distance of the flare exit from throat etc ) on combustion performances are studied experimentally. the experimental results show that radial profiles of the outlet gas temperature 、 combustion efficiency 、 emissions of co2 、 co and nox and lean blowout are affected with different degrees by the different geometric parameters of dual - stage swirler and the arrangement of primary holes
在不同油氣比下，不同的雙級旋流器幾何參數（例如:一級與二級旋流器出口內徑d 、葉片安裝角、二級旋流器出口外徑d 、二級旋流器的喉道到出口截面的距離l和喉道前後的圓弧半徑r以及主燃孔孔布局等）對單頭部環形燃燒室的出口溫度分佈、燃燒效率、貧油熄火油氣比以及污染物（ co _ 2 、 co和nox ）排放等燃燒性能的影響規律進行了研究。 -
Rolling bearings - angular contact radial ball bearing - part 6 : single row, contact angle 15 and 25
滾動軸承.角接觸徑向球型軸承.第6部分:單列，接觸角15 -
Analytic relationships among radial clearance, axial clearance, contact angle, center distance between two grooves, and bearing fit gap are derived for bearing design ; 3. analytic relations of radial fit gap and radial clearance is derived for bearing production
推導出了雙列角接觸球軸承的軸向游隙與徑向游隙、雙溝溝心距及軸承配套間隙之間的解析關系式，可應用於軸承設計。 -
Radial emission angle 12
徑向發射角： 12 -
Radial emission angle 33
徑向發射角： 33 -
Radial rake angle
徑向前角 -
The paper deduced the seal torque of the tri - eccentric butterfly valve and gave it a qualitative analysis. the results indicated : for the tri - eccentric butterfly valve with the same caliber, theseal torque would decrease with the butterfly disc thickness increasing ; the seal torque would increase with the radial eccentricity increasing ; however, the axis eccentricity effected on the seal torque minutely ; the seal torque would increase with the half cone angle increasing appreciably of the cone which the butterfly disc belonged to
本文還對三偏心蝶閥的密封力矩作了推導並進行了定性的分析，結果表明，對于同一口徑的三偏心蝶閥，密封力矩與蝶板的厚度近似成反比；與徑向偏心距近似成正比，變化也很明顯；而軸向偏心距對密封力矩的影響不是很大；密封力矩隨著蝶板所在的圓錐半錐角的增大而有所增加。 -
In conclusion, based on radial basis function neural networks, a method of identifying vehicle steering angle is proposed for further investigation of the vehicle handling inverse dynamics. the identification results show that the method is not only feasible, but also with high accuracy, little computation requirement and good stability
綜上所述，本文利用徑向基函數網路建立了汽車橫擺角速度響應與方向盤轉角的非線性映射關系，根據模擬試驗測得的數據，由汽車的橫擺角速度響應識別出了方向盤的轉角輸入，具有很高的精度和抗干擾能力。 -
Adopted auto - shadowing cut - grinding system to ensure pressure angle, axis power and radial power in a best position
採用自動跟蹤磨削系統，確保壓力角軸向力徑向力最佳。
分享友人