rate controlling process 中文意思是什麼
rate controlling process
解釋
速率控制過程-
The relation between the ablation rate and the process parameters of sand blasting in color pdp is studied and formularized in this paper. the methods of controlling sand - blasting process with the rib paste ablation rate formula are put forword, whick can be useful to the control ability of sand blasting process and the consistency of the barrier rib
本文討論了彩色pdp噴砂工藝中障壁粉清除速率與噴砂工藝控制參數之間的關系，提出了用障壁粉清除速率公式來控噴砂工藝的方法，這對提高噴砂工藝的可控性及障壁製作的一致性具有實用性價值。 -
Abstract : the relation between the ablation rate and the process parameters of sand blasting in color pdp is studied and formularized in this paper. the methods of controlling sand - blasting process with the rib paste ablation rate formula are put forword, whick can be useful to the control ability of sand blasting process and the consistency of the barrier rib
文摘:本文討論了彩色pdp噴砂工藝中障壁粉清除速率與噴砂工藝控制參數之間的關系，提出了用障壁粉清除速率公式來控噴砂工藝的方法，這對提高噴砂工藝的可控性及障壁製作的一致性具有實用性價值。 -
The planeness and integrality of the flier - plate were ensured effectively by exerting restrictive pressure, controlling heating and cooling rate, lowering welding temperature or reducing welding time as much as possible, etc. theoretical model of creating quasi - isentropic compression via 93w - ofc - tc4 - a1 - mb2 system flier - plate with graded wave impedance was established, and numerical simulation of the impact process was then carried out
採取施加外部機械力、控制升降溫速率以及盡量降低焊接溫度或減少焊接時間（防止脆性金屬間化合物的過度增長）等措施，確保了焊接接頭的平整性和界面結構的完整性。建立起梯度飛片擊靶的理論模型，對93w - ofc - tc _ 4 - al - mb _ 2系波阻抗梯度飛片的擊靶過程進行了數值模擬計算。 -
Abstract : the mechanism, stages and controlling step of hot metal desiliconization process are investigated, and the methods intensifying process and increasing reaction rate are proposed
文摘:研究了鐵水脫硅過程的機理、組成環節和控制步驟等動力學問題，提出了強化過程和提高過程速率的方法。 -
Abstract : based on the rigid visco - plastic fem technique, this paper numerically simulate the superplastic bulging process of void - sensitive materials using pressure controlling strategy of maintaining maximum effective strain rate constant and void damage evolution model of superplastic forming
文摘:基於剛粘塑性有限元技術採用最大應變速率恆定的壓力控制策略和超塑性成形空洞損傷演變模型對空洞敏感材料的超塑性脹形過程進行了數值模擬。 -
2. effect of the viscosity ratio, mterfacial adhesion, processing conditions and composition on the dispersing morphology and properties of pp / eoc blends was investigated. low viscosity ratio and high shear rate during processing were found to produce fine and uniform dispersion of eoc in pp matrix, while low viscosity ratio, high interfacial interaction, good fluidity of elastomer and high shear rate in molding process resulted in fibril dispersion, which afford a guide for controlling the morphology of pp / eoc blends
研究了粘度比、界面相互作用、加工條件和共混比例等因素對pp eoc體系分散形態和性能的影響，發現粘度比小和加工過程中剪切強度大有利於彈性體在基體中分散均勻細化；粘度比小、界面相互作用強、彈性體本身的流動性好及成型時受到的剪切應力大，使彈性體相易變形，沿流動方向取向呈纖，闡明了各因素對形態影響的作用機制，這對pp eoc共混物的形態控制具有重要的指導作用。 -
Gas analysis is used to optimize the blast furnace process, including reducing the consumption rate of coke and controlling the temperatures inside the furnace ( ref 4 )
氣體分析用於優化高爐過程，包括還原過程中焦炭的消耗速度和爐內的溫度控制。 -
On condition of controlling solid - liquid interface preferably and keeping low directional solidification rate, there were particular phenomena in tasi2 fibre development process. generally, it can be divided into three typical steps. the first was star - up period, the second was competition period, the third was stabilization period
在較好控制固液界面和較低的生長速率定向生長條件下，纖維相tasi _ 2生長過程有其獨特的規律性，通常可以將其生長過程分為啟動、競爭、穩定三個典型階段。
分享友人