rate of bending 中文意思是什麼
rate of bending
解釋
彎曲速度-
Test method for determination of the modulus of elasticity for rigid and semi - rigid plastic specimens by controlled rate of loading using three point bending
用三點彎曲法測定在裝載控制速度下剛性和半剛性塑料樣品彈性模量的方法 -
Standard test method for determination of modulus of elasticity for rigid and semi - rigid plastic specimens by controlled rate of loading using three - point bending
用三點彎曲法測定在裝載控制速度下剛性和半剛性塑料樣品的彈性模量的標準試驗方法 -
Two different reinforcing methodologies are applied : modification of the overlay characteristics by adding chopped glass fibers to the hot mixture asphalt ( hma ) and reinforcing asphalt overlay with glass grids. theory of fracture mechanics ( fm ) is employed to determine crack growth rates for the suggested anti - cracking overlay systems. asphalt mixture designing tests, three point bending tests and fatigue crack propagation tests were carried out. the critical stress intensity factors kic are determined for plain and reinforced asphalt concrete. depending on the fatigue crack propagation, the crack growth rate is determined for each type of anti - cracking system and the cracking process is also analyzed. one of the significant points in this study is the attempt to give better understanding of the crack propagation for multilayer asphaltic overlay or what are suggested herein to be called composite structure anti - cracking overlay system. the results indicate that the reinforcing materials improve anti - cracking characteristics of the asphalt concrete. composite structure anti - cracking overlay gives a good solution for the reflective cracking phenomenon over old cracked pavements
利用2種不同的方法加筋瀝青罩面:在瀝青混合料中加入短切玻璃纖維改善瀝青混凝土的特性，採用玻璃格珊加筋瀝青混凝土.應用斷裂力學方法分析瀝青路面裂縫擴展機理.採用瀝青混合料設計試驗、三點彎曲試驗和疲勞裂縫擴展試驗，確定加筋瀝青混凝土的臨界應力強度因子kic ，測量每一種瀝青罩面抗裂系統的裂縫擴展速率.本研究的主要特點是提出復合型抗裂罩面系統，分析了多層加筋瀝青罩面裂縫擴展過程，推薦了若干瀝青路面抗裂系統.結果證明，加筋材料可以提高瀝青罩面的抗裂特性，復合型抗裂罩面系統能夠有效地阻止反射裂縫的擴展 -
In the process of preparing glass / mullite composite material, research on shrink rate, bending strength, dielectric constant, dielectric loss tangent, etc have been carried out. in the experiment, the thermal expand coefficient of samples is tested, and through sem, insides structure of sintered sample is studied, so the relationship of
在制備玻璃/莫來石復合材料的過程中，我們研究了燒成后徑向收縮率、試樣的抗彎強度、介電常數、介質損耗及其影響因素，並測試了試樣的熱膨脹系數，通過sem觀測燒成試樣的內部結構情況，找出性能和結構之間的關系。 -
The structure shearing force takes a one - way increasing trend with the decrease of ratio of beam bending rigidity and pier lateral displacement rigidity and the increasing rate is bigger. when the consolidation at the bottom of pier is elastic consolidation and the structure force is bigger the extreme value mentioned at the above, the structure force will take a increase with the decrease of ratio ; and when the structure force is smaller the extreme value, the improvement of the inner force at the bottom of pier is distinct adopting elastic consolidation and bending of at the top of pier and beam will has a great increase
對于墩底採用彈性固接時，結構內力在梁、墩剛度比不低於前述固接墩出現極值點時剛度比的情況下，將出現內力值隨剛度比的增加而減小；而在梁、墩剛度比小於極值點剛度比時採用彈性固接對墩底彎矩改善較大較為明顯，對墩頂及主梁的彎矩將會有較大幅度的增加。
分享友人