reactant temperature 中文意思是什麼
-
Based on orthogonal test, the factors influencing the synthesis of di - n - propyl phosphite, such as reaction temperature, reaction time and molar ratio of reactant, were investigated
通過正交優化試驗，考察了溫度、時間和物料配比對二正丙基亞磷酸酯的合成收率的影響。 -
The explanation could lie in the sharp temperature jump a particle experiences when it becomes dispersed in a bubble of reactant gas.
其解釋是當顆粒被分散於反應氣體的氣泡中時，經受著溫度的突然躍升。 -
The main point can be summarized as follows : a low - temperature elemental - direct - reaction route to nanocrystalline cdse and znse, and further more, by using the newly produced se with high reactivity as reactant, a controllable synthetic route named " selenite reduction hydrothermal method " have been developed
在合成新途徑的探索方面，從發現了水熱元素直接反應法，發展到亞硒酸鹽水熱還原法，提出了化學調控合成的新概念，為液相中金屬硒碲化合物的合成提供了可能的動力學調控手段和方法。 -
The factors, such as reactant concentration, medium acidity, stirring speed, washing and drying temperature, directly influence purity, structure and yield of the product
反應物濃度、介質溶液的酸度、攪拌速度、沉澱分離后的洗滌、乾燥溫度等對產物的純度、結構和收率都有直接影響。 -
To determine influence of technical conditions on product diameter, the influences of concentrations, molar ratio, reaction temperature and time on average size were investigated by means of uniform design. the results of experiments indicated that product diameter was mostly influenced by reaction temperature, followed by molar ratio of reactant, concentration of reactants, and reaction time. the optimum conditions were c ( co ( no3 ) 2 6h2o ) = 0. 35mol / l, n ( co ( nh2 ) 2 ) : n ( co ( no3 ) 2 6h2o ) = 3. 53 : 1, reaction temperature 94 and reaction time 3. 53h
以產物的平均粒徑（ nm ）為優化指標，選擇硝酸鈷濃度、反應物摩爾比、反應溫度和反應時間四個因素，運用均勻試驗設計技術進行3 ~ 5 1 ~ 3因素優化試驗，發現反應溫度對產物的粒徑影響最大，其次分別為反應物摩爾比、硝酸鈷濃度以及反應時間，並確定最佳反應條件為：硝酸鈷濃度0 . 35mol l ，反應物摩爾比為3 . 53 ： 1 ，反應溫度94 ，反應時間3 . 53h ，預報值粒徑y _ 1 = 19 . 57nm ，在此優化條件下制得的納米co _ 3o _ 4平均粒徑為22nm 。 -
The optimum technic conditions have been gotten in in preparaing high dispersive a1 ( oh ) 3 colloid by controlling reactant concentration, ph value, reaction temperature, matured time. they are the prereguisite to prepare nanopoder of a - a1203. this paper entirely and systematically studies the following three kinds of drying stages : oven drying, dehydration with alcohols and azeotropic distillation stage
本文採用逐步逼近法進行了氫氧化鋁膠體的沉降實驗，對膠體形成的體系反應物的初始濃度、體系的ph值、反應溫度和膠體的陳化時間進行了系統優化，並獲得了制備高分散氫氧化鋁膠體的最佳工藝參數；此膠體經過過濾、 80下烘乾后所得樣品，在掃描電鏡下直接觀察其粒徑為50nm ，且分佈范圍窄，顆粒的表面清潔，為球形。 -
In the production process of beta - cypermethrin, the overall yield was improved from 60 % to 93 % and the content of the final product was increased from 90 % to 95 % by optimizing technical conditions in the aspects of various starting materials, temperature control, reactant ratio, the mode of discharge, stir type, stir speed and etc
摘要在高效氯氰菊酯的生產過程中，通過不同原料合成氯氰菊酯的選擇、溫度控制、投料比、出料方法、攪拌類型及轉速的選擇等方面的工藝探索，產品收率由60 %提高到93 % ，含量由90 %提高到95 % 。 -
The effect of the mole ratio reactant, reaction temperature, reaction time, catalyzer on the each reaction were studied. the optimum reaction conditions were obtained
研究反應物配比、反應溫度、反應時間、催化劑用量對各步反應的影響，得到最佳反應條件。 -
This paper firstly synthesized the maltose fatty acid ester by agent - in - water method. the influences of reaction time, temperature, proportion of reactant ect. on synthesis have been observed
摘要本實驗首次以麥芽糖漿為原料微乳化法合成麥芽糖酯，以酯得率為考察目標，主要探討了反應過程中時間、溫度、反應物配比等因素的影響，並對產品的理化性質作初步分析。 -
Meanwhile, the reaction conditions for synthesis of propaphos, such as reaction temperature, reaction time, molar ratio of reactant were investigated, and the optimal one were found as the following : molar ratio of 4 - ( methylthio ) phenol, phosphite and sodium hydroxide 1 : 1. 4 : 2. 3, reaction temperature 70, reaction time 2 h
同時，較系統地考察了高選擇性有機磷殺蟲、殺菌劑丙蟲磷的合成的工藝條件如反應溫度、反應時間、縛酸劑種類以及縛酸劑的用量。 -
The key hydrogenation parameters are radio frequency power, reactant gas ration, temperature, time
主要的氫化參數有射頻功率、氫氣流量、樣品溫度、處理時間。 -
After extensive conditional experiments such as reactant concentration, acidity ph, temperature and time of reaction have been done, and the factors influencing the sol stability such as washing method, drying temperature and roasting temperature and time have been discussed, the best conditions in this work are given
通過考查超細粉體制備過程中反應物濃度、 ph值、反應時間與溫度、影響溶膠穩定性的因素、洗滌方式、乾燥溫度、燒結溫度與時間對產品性能影響的大量實驗，給出了本實驗的最佳參數。 -
We have studied the influence of growth parameters of buffer layer under large flux of reactant materials and found that parameters such as v / ratio, growth temperature and ammonia flux during annealing have evident influences on the growth of buffer layer, while other parameters like growth pressure, pressure during annealing and ramping rate show little influence
在大源流量流下，研究了gan緩沖層各生長參數的影響規律，發現對緩沖層生長影響顯著的條件有生長比、生長溫度、退火時的氨氣流量。而緩沖層生長壓力、退火壓力及退火時間的影響相對較小。 -
Based on analyzing the defects existing in traditional sonochemical reactors, the authors developed a new type of sonochemical reactors that controls the reactant temperature by cooling and heating
摘要在分析傳統聲化學反應器缺陷的基礎上，研製了一種新型聲化學反應器。 -
( 1 ) carbon aerogel and xerogel were made from resorcinol - formaldehyde organic gels and used as the anode materials for lithium ion batteries. by discussing the influences of pyrolysis temperature, the level of the catalyst and the concentration of reactant in the preparation of carbon materials on their behavior of lithium ion storage, their performance of storing lithium ions and process of charge and discharge were studied in details. moreover, the relationship between the structure of carbon aerogel and xerogel and the performance of storing lithium ions was analysed, and the mechanism of the storage of lithium ions in this type of porous carbon materials based on organic gels was also dicussed simply
（ 1 ）從合成間苯二酚-甲醛有機凝膠出發，制備了碳干凝膠和氣凝膠，研究了其作為鋰離子電池碳陽極材料的儲鋰性能，探討了碳材料制備過程中的熱分解溫度、催化劑用量、反應物含量等條件對碳干凝膠和氣凝膠儲鋰行為的影響，並分析了碳材料結構與儲鋰性能的關系以及充放電過程，也簡單探討了鋰離子在這類基於有機凝膠的多孔碳材料中的存儲機制。 -
It is also found that the concentrations of reactant, catalyst, the time and temperature of action and the working conditions have perceptible effects on its membrane performances. in this paper, the application of these membranes is also introduced
探討了原料濃度、交聯劑種類和濃度、催化劑、添加劑、反應時間和反應溫度對膜性能的影響，初步計算了聚乙烯醇/ 5102一a12o3復合納濾膜各膜層的阻力。 -
We studied the different parameters ’ influences on the structure and the performances of snsb produced by chemical coreduction method, including the synthesizing temperature, desiccating time, the ph value of the reducing agents, and the reactant contents and made some improvements on the preparation methods
採用化學還原法制snsb ，研究了合成條件對snsb結構和電化學性能的影響，討論了合成溫度、乾燥時間、還原劑ph值、不同摩爾比對材料性能的影響，優化了反應條件。
分享友人