reasonable velocity 中文意思是什麼

Numerical calculative simulation could factually reflect the dynamic characteristics of the whole equipment and inner flow and diathermancy of split - stirling crycooler. through the calculation, the velocity, temperature, pressure and other detailed information of airflow in any position inner the crycooler could be gained ; the distribution of each parameter could be confirmed and reasonable explanation for the experiment result could be made

數值計算模擬能接近真實地反映分置式斯特林製冷機的整機和內部流動、傳熱的動態特性，通過計算可以得到製冷機內部任一位置的氣流流動的速度、溫度、壓力等詳細信息，確定各參數的分佈情況，並可以對實驗結果做出合理的解釋。

Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution

在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。

In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys

本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。

A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。

So according to the technology regulation of reclamation engineering, hydraulic calculation must be carried out in the design of final closure. this paper firstly introduces the progression and present situation of reclamation engineering, emphasizing on the features of present reclamation and on the experiences and theories of home and abroad ; using fortran perfects the hydraulic calculation program of the closure and makes the program to meet different conditions ( such as considering flood, the variation of time interval, multi - entrance, multi - reservoir capacity ), and after comparing and analyzing a great deal of schemes, the reasonable computation scheme was brought up ; the interface of the program was carried out by the programming language vb to make the process of calculation become easier and more distinct, so the result can be analyzed and handled more directly ; vb is used in the later management of the result to plot the graphic chart of the isoline of the maximum of hydraulic element ( the velocity of flow, the drop height and the rate of flow ) automatically ; finally it was applied in the reclamation project of dongbidao of fuqing

本文首先介紹圍海工程的發展進程與國內外圍海的開發現狀，重點介紹了我國目前圍海工程的特點及在圍海工程實踐中積累的經驗和理論；利用fortran語言完善堵口工程龍口水力計算程序，使程序可以滿足圍海工程復雜工況下（如考慮內港洪水、計算時段的變化、多口門、多庫容、多水閘）的龍口水力計算，並進行大量方案的比較和分析，提出合理計算方案；利用面向對象的可視化編程語言vb進行界面開發，使計算過程有良好的人機界面，更直觀地對計算結果進行分析和處理；計算結果的后處理採用vb編程實現龍口水力要素最大值等值線圖的繪制；並運用所編軟體對福建省福清市東壁島圍墾工程進行龍口水力計算，為堵口合龍提供科學依據。

In addition, a series of reasonable time histories of helicopter velocity, angular velocity and flight attitude were shown during the given dolphin maneuver flight

最後以黑鷹直升機為例計算了魚躍越障機動飛行時駕駛員操縱輸入及直升機速度、角速度和飛行姿態的變化規律。

According to characteristics of the seismic data from the low snr region with complex surface, this paper is started from solving the static correction problem and reasonable eliminating all kinds of disturbance in the seismic data from the low snr region with complex surface. through the whole process of seismic data processing which includes a series of processing methods that are suitable for the low snr region, namely, from the choosing of the floating base - level, the static correction in the field and indoors, the eliminating of all kinds of noise before and after stacking, the velocity analysis with high - resolution, the reasonable techniques of deconvolution before stacking and wavelet processing after stacking, to the method choosing of the high - resolution stacking and the reasonable and accurate offset imaging, a set of the complete and effective flow for processing seismic data from the low snr region with complex surface are finally formed, which can meet the need of explo

本文針對復雜地表低信噪比地區地震資料的特點，以解決復雜地表低信噪比地區地震資料靜校正問題及合理剔除各類干擾為出發點，在整個地震資料處理過程中，從浮動基準面的選取、野外及室內靜校正、疊前疊后各類噪音的去除、高精度速度分析、合理的疊前反褶積及疊后子波處理技術、到選用高精度的疊加技術及合理準確的偏移成像方法等一系列適合於復雜地表低信噪比地區的處理方法，最終形成一套較完整且有效的針對復雜地表低信噪比地區地震資料的處理流程。

The fact that wave velocity in quasi - saturated soil is equal to that of fully saturated soil could not be calculated by effective fluid compressibility or explained by unwell - distributed saturation. we account for this in a new reasonable way which was based on kuster scattering effect analysis

（ 8 ）根據kuster散射波理論，計算了飽和度大於85的準飽和土體的彈性波速，其結果與試驗非常吻合；但是，通常所用的等效孔隙流體壓縮系數的方法所計算的結果與實驗結果差別很大，對此，筆者給予了一定的解釋。

The best match between cooling efficiency and power can be obtained by choosing a reasonable flow velocity

合理選擇流速可以達到冷卻效率與動力的最佳匹配。

As the cam profile with constant - velocity - constant - acceleration ramp feature and with continuous higher derivative lift feature is widely adopted in the advanced high - speed internal combustion engines, the cam ramp profile is fitted with a reasonable function and the cam - lift profile is fitted with a polynomial function

考慮到高速內燃機的凸輪大多採用具有等加速-等速特徵的緩沖段和高階導數連續特徵的工作段型式，用等加速-等速函數擬合緩沖段實測升程數據，用整體式高次多項式函數擬合工作段實測升程數據。

This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。

Combining the results of the analysis on the bed resistance, the velocity distribution and the rules of index number n. " s changing, the mechanism of the abatise groups " beach protection and accretion promotion effect is sought. the result indicates that the conclusions of the thesis are reasonable and reliable and the index number n is effective for engineering application

本文關于混凝土榪槎群水力學特性的主要研究結論，符合理論上的定性分析，得到了其它研究成果的印證，提出的指標（底流速衰減率、護底效果指標）的取值基本合理，可以作為工程應用和進一步研究的基礎。

Experimental research shows that, the designed main mechanism is reasonable ; swimming velocity varies with the frequency exerted on ; steering motion can by realized by changing the frequency f, and f2 of control power which exerts on two pzt. finally

實驗結果表明： （ 1 ）液體中微機器人的主體結構設計是合理的； （ 2 ）通過改變電源頻率可控制微機器人的泳動速度。

In this article, constituting some the equations which reflect the flow law and building and applying many mathematical models of physical and chemical reactions in the the plasma ignition : applying k - two equations turbulence model to calculate the turbulence parameter supplying simplied reaction systerm model and applying eddy break - up model and p - i thermal radiation model. with these reasonable simplied modles, numerically simulating the flow field in the plasma ignition. during the numerical simulation, applying the body - fitted coordinates for the complex geometry of the computional field ; using the mixing format to disperse the equations ; applying simplec algorithm method to solve the equations ; using above models and methods, it can get flow field distribution ; including temperature, pressure, turbulent kinetic energy and its dissipation rate, turbulent viscosity, velocity, density. these results are significant to design and improve the plasma ignition

本文旨在通過構造反映等離子點火器內部流動規律的基本方程組，建立描述等離子點火器內部的復雜物理化學過程機制數學模型：模擬等離子發生器內部燃燒的-雙方程湍流流動模型；模擬氣體燃料在燃燒時中化學反應的簡單化學反應系統模型；模擬等離子點火器內部湍流預混燃燒的漩渦破碎模型；模擬等離子點火器高溫燃氣及其壁面的p - i輻射換熱的模型等等，對模型進行一定的合理的簡化，然後數值模擬等離子點火器內部流場的流動。

Based above, a two - grade fuzzy comprehensive evaluation model is presented on the ground of the current seismic design code for building. it is that taking the membership of equivalent shear velocity as weight of the model not empirical weight in traditional one - grade model. it has been proved in site classification reasonable

參照我國現行建築抗震設計規范，改變過去以經驗系數為權重的一級模糊綜合評判模型，以等效剪切波速對各場地土的隸屬度為權重，建立了場地二級模糊綜合評判模型，對場地進行劃分。

We make up a simple model based on the microscopic mechanism of the membrane to investigate this phenomenon. the model proves reasonable after we quantify the velocity of the pearls drift slowly towards the laser trap

對於此動力學行為，本文從膜的微觀結構出發，建立了一個簡單的模型，解釋了珠鏈狀膜的形成以及光鑷熄滅后水珠的運動。

And the conclusion is that vita method is a more reasonable method in burst detection when the threshold value is between 0. 7 to 1. 0. in order to investigate the influence of transverse curvature of the wall, the direct numerical simulated data bank of turbulent channel flow is also analyzed. the mean velocity profile in pipe and channel flow is compared

本文還對圓管和槽道內的猝發事件進行了分析，得到的圓管和槽道內的猝發周期大致是相同的，但是在猝發的強度上槽道要大於圓管；並且進一步的分析表明猝發強度的差別主要在於徑向速度的差別，這說明壁面橫向曲率對于徑向的流動影響較大，而對流向流動幾乎沒有影響。

We can analyze and observe directly the reasonability of processed data, that is helpful to improve the quality of tomography inversion and the reliability of velocity model tomography inversion, then provide reasonable surface velocity model for tomography static correction by some means, such as rotating, scale graphics, meanwhile combining with relating sectional drawing and clipping drawing

通過對三維立體進行全方位旋轉、縮放顯示，並結合與三維體一致的剖面和平截面的綜合考察，便於直觀地分析、監控地震數據處理結果的合理性，有助於提高模型層析反演的質量和表層速度模型層析反演的可靠性，並可為層析靜校正提供合理的表層速度模型。

The calculated results of cold nozzle flow are in agreement with some cold test one. through calculation, the parameter distributions of regulated nozzle flows were obtained. they state that the design of the regulated nozzle is reasonable, and its velocity loss at discharge section is less than 2. 3 % comparison with no regulated nozzle

3 、計算結果與已有的試驗結果對比相符，計算獲得了可調噴管的流場參數分佈，表明可調噴管的設計合理，與不可調噴管相比，流動的出口平均速度損失小於2 . 3 。

Abstract : concerning the models for discribing aerodynamic stability of axial flow compressor, the original model is one - dimensional, and it is reasonable for the onset of surge only. for the onset of rotating stall, there are just some two - dimensional models at published literatures. a three - dimensional aerodynamic of compressor has been presented in this paper. an aerodynamic stability model concerning radial disturbance of compressor is presented. the calculated results show that the occurrence of radial disturbance is related to the axial velocity disturbance, which has important effect on aerodynamic stability of compressor. the position of onset of stall, in blade tip or hub, is dependent upon the characteristics of blade element. the comparisons of calculated results predicted by 2d and 3d aerodynamic stability model have also been made in this paper

文摘:軸流壓氣機的氣動穩定性模型，最初為一維模型，僅適用於描述喘振發作.對于旋轉失速發作，在公開文獻中有一些二維模型發表.本文提出了一類考慮壓氣機徑向擾動對失速影響的新的氣動穩定性模型.計算結果表明壓氣機的軸向擾動往往隨著徑向擾動的產生，徑向擾動的強度影響壓氣機的氣動穩定性，在葉尖還是葉根首先產生失速與壓氣機基元葉柵特性密切相關.本文對軸流壓氣機二維和三維氣動穩定性模型的計算結果進行了對比分析