rectangular axis 中文意思是什麼

rectangular axis 解釋
直交軸
  • rectangular : adj. 矩形的，長方形的；成直角的。
  • axis : n （ pl axes ）1 軸，軸線。2 【植物；植物學】莖軸。3 【解剖學】第二頸椎，第二脊骨。4 【政治學】軸...
  1. In this thesis, studies are focused on as follows : ( 1 ) based on analyzing the general transfer - matrix, the conception of the generalized double layer soil model is proposed, and the transfer - matrix ( r ) of half - infinite elastic mass is introduce - d to the analytic expressions of stress and settlement under the uniform circular, rectangular and strip vertical loads in multi - layered soil ; ( 2 ) according to the analytic expressions of the additional stress and settlement under unifo - rm circular in multi - layered soil, rectangular and strip vertical loads, the programs are develop - ed to resolve and debugged. the results show that the programs are correct ; ( 3 ) through calculating the coefficient of additional stress on the central axis of uniform circ - ular vertical loads, under the corner point of the uniform rectangular vertical loads, and on the central axis of uniform strip vertical loads, and the settlement on the center of uniform circular vertical loads and uniform rectangular loads in double - layered soil, the characters of stress and settlement are discussed ; ( 4 ) a case, as an example, is studied with different calculation methods, such as traditional theory, fem. the results obtained are compared

    本文在已有研究成果的基礎上進一步開展了以下幾方面的研究： （ 1 ）在對層狀地基傳遞矩陣法中的總傳遞矩陣分析的基礎上，提出了廣義雙層地基模型的概念，並把半無限體的傳遞矩陣r引入到多層地基在圓形垂直均布荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式中； （ 2 ）根據多層地基在圓形荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式，編制了程序，調試通過並驗證了其正確性； （ 3 ）通過對雙層地基圓形垂直均布荷載中心軸線上的附加應力系數和荷載中心沉降，矩形垂直均布荷載角點下的附加應力系數和荷載角點沉降及條形垂直均布荷載中心軸線上的附加應力系數進行的計算，探討了雙層地基中的附加應力與沉降特性； （ 4 ）應用本文的層狀地基體系理論對一個工程實例進行了計算分析，並與傳統的計算方法的計算結果和有限單元方法的計算結果進行了對比分析，結果表明利用層狀地基理論計算更能反映地基中附加應力分佈的實際情況。
  2. Considering the characters of 3 - axes coordinate system that is not included in ship rectangular frame or inertial frame, compensation conditions are deduced through studying the effects of ship - swing. the paper studies how to transfer line velocity and acceleration in the inertial frame to angular velocity and acceleration which correspond each axis, then gives the computer function scheme. servo control scheme which can overcome ship swing and realize moving - target accurate tracking is designed according to inconsistency of radar base angle and beam angle

    針對三軸軸系既非甲板坐標系又非大地坐標系的特點，既研究了船搖對正交三軸雷達系統的影響，推導實現船搖不變性的補償條件，又研究了將目標在大地坐標系中的線速度和線加速度濾波值折算到各軸對應的角速度和角加速度值的計算關系，並作出了計算機功能框圖。
  3. Asm 1. 0 contains the entire ccos process, including best - fit sphere calculating, profiler test and anslysis, virtual grinding and polishing, cnc grinding and polishing, etc. as results, the manufacturing process of a f / 1. 17, 770mm x 200mm rectangular even high order off - axis aspheric mirror is presented as an example in detail

    最後，比較詳細地介紹了770mm 200mm ， f 1 . 17高次離軸非球面反射鏡的加工、檢驗過程，加工后200mm口徑范圍內加工精度達到0 . 013 rms ，完全滿足了設計要求。
  4. The mechanism is based on the 4 - axis rectangular coordinate system. the driven mode of x - axis is proportional pneumatic - servo control system ; y - axis is driven by a digital ac servomotor ; z - axis is driven by a linear cylinder ; the driven mode of the axis of r is same to that of y - axis

    X軸採用基於比例伺服技術的氣動驅動； y軸採用全數字交流電機伺服驅動； z軸則採用直線氣缸驅動；而r軸採用與y軸相同的驅動方式，同時其前端安裝了真空吸盤，用於抓取工件。
  5. The results of case a and case b were about the same, thus it was displayed that modifying structure did not cause the bursting under low pressure but the damages of the structure. second, an analytical model was developed to assess the critical buckling problem of near surface interlaminar rectangular defects in the cylindrical part of srmcs under axis and interior pressure loads. the relationships between critical strain value and the parameters of geometry and radius of cylindrical were discussed

    在最大壓力為水檢壓力的作用下，應用有限元計算出殼體的整體變形以及不同部位的各種應力（不同應力分量）和位移分量，與試驗結果均比較吻合，證明採用大變形方法分析殼體宏觀應力和變形是合理的， a殼體與b殼體的應力、變形情況基本相同， b殼體發生低壓爆破不是由於結構參數的調整造成，而是由於各種試驗導致的累積損傷造成的。
  6. Dynamic behavior and buckling analysis of thin rectangular plate rotating around its symmetrical axis

    軸對稱勻速轉動狀態下矩形薄板的動態特性與屈曲分析
分享友人
分享到 Line

分享到臉書