regression design 中文意思是什麼

regression design 解釋
回歸設計
  • regression : n. 1. 復歸，回歸。2. 退步，退化。3. 【天文學】退行。adj. -sive ,-sively adv.
  • design : vt 1 計劃，企圖，立意要…。2 指定，預定；留給，留著。3 設計，草擬，擬定，籌劃；起草，畫草圖，打（...
  1. In this paper, the effects of fly ash, cement, lime, fine sands, foam agent, w / c ratio and additional agent on foamed concrete were studied by experiments, the best combination ratio of fly ash foamed concrete whose density varies from 551kg / m3 to 650kg / m3 was obtained through orthogonal test design, the foam agent quantity and the fly ash quantity effect the fly ash foamed concrete greatly, so the author selected them as independents to establish duality linear regression equations, the equations were quite ideal through the test of model summary r. moreover, the author also did some experiments about the water resistance of magnesium oxychloride cement fly ash foamed concrete, the outcome showed that phosphoric acid has good effect on water resistance, and its appropriate quantity was found

    本文通過試驗研究了粉煤灰、水泥、石灰、細砂、發泡液、水灰比及外加劑對粉煤灰發泡混凝土性能的影響，採用正交設計試驗方法得出了600級粉煤灰發泡混凝土的最佳配合比，同時發現發泡液和粉煤灰摻量對發泡混凝土的影響最為顯著，因此，以二者為自變量建立了二元線性回歸方程，通過全相關系數的檢驗發現方程較為理想。此外，還對氯氧鎂水泥基粉煤灰發泡混凝土的耐水性進行了相關實驗，發現磷酸有較好的耐水性效果，同時找到了其合適的摻量范圍。
  2. Regarding the serious smoke ejection of 75 diesel engine series, this paper points out that this problem could be solved by modifying certain parameters and employing gyrating regression design. the actual experiment on 375 diesel engine series shows that, after innovation, the maximum of smoke ejection of gyrating moment falls by 24. 2 percent, and then the rating is demarcated, the smoke ejection falls by 53. 8 percent

    本文針對75系列柴油機排煙嚴重的問題，通過改變噴油嘴及相關調整參數，利用多因素正交旋轉回歸設計安排試驗，取得了較好效果.在375型柴油機上的實驗結果表明：進行優化匹配調整后，最大扭矩點煙度下降24 . 2 ，標定工況時煙度下降53 . 8
  3. We select ni / cr alloy resistor as element together with ceramic embedding hearth ; select small flat - and - disc heat - even hubby ceramic sample holder, select ni / cr & ni / si thermoelectric couple ( type k ) as thermoscope with threads 0. 5 mm in diameter which is installed in the middle of the holders symmetrically ; select aluminum silicate fire - retardant fiber as materials for heat preservation ; design some hardware, for example temperature controller & transporter, signal amplifier etc ; design controlling curve to heat stove ; and introduce the method of least squares nonlinear regression and subsection function to deal with data. in order to obtain the reasonable operation conditions and operation curve, we have also done many theory analysis and experiment discussions

    通過理論和試驗探討，選用鎳鉻合金電阻絲作為加熱元件，配以陶瓷質埋入式爐膛；選用陶瓷質小尺寸扁平?圓盤均熱塊體型樣品支持器；選用0 . 5mm絲徑鎳鉻?鎳硅熱電偶（ k ）作為測溫元件；熱電偶對稱安置在樣品支持器容器的中部；選用硅酸鋁耐火纖維作保溫材料；合理選用和設計了溫度控制器、溫度變送器、信號放大電路等硬體；採用升溫曲線來控制爐膛供熱過程；採用最小二乘法非線性回歸與分段函數相結合的曲線模擬方法，進行圖形處理。
  4. In view of our country ' s climate differences and research object is passive building, suggests that using the linear regression of neutral temperature to set up the bio - climatic building design chart ( bbdc ) for passive buildings

    考慮到我國氣候的多樣性以及本文的研究目的，在建立氣候分析圖時，提出了利用描述自然房間室內中性溫度的線性回歸關系式，作為確定熱舒適區的依據。
  5. The result of orthogonal experiment and secondary regression experiment on the bionic disk plows indicates that the bionic non - smooth partial sphere structure cell can decrease resistance by almost 30 % than common plow in the condition that the structure and distribution combine rationally. therefore, the bionic design and experiment research on disk plows is very significant

    仿生圓盤犁刀的正交試驗和二次回歸試驗結果分析表明，如果圓盤犁刀的仿生非光滑球冠結構單元的結構參數和分佈組合搭配合理，仿生圓盤犁比普通圓盤犁可減少阻力約30 ，因而本文對圓盤犁刀進行仿生設計與試驗研究是非常有意義的。
  6. Different equations to corresponding components are presented by analysing and transformating the general equations of fluid routes, then static characteristics mathematical model of liquid propellant space propulsion system is presented. based on the data of static characteristics calculation, mass model of thruster, propellant, propellant tank, gas, gas bottle, pipe and valve is presented using both the method of statistical regression and the method of stress analysis, then corresponding mass model is presented. based on the characteristics of liquid propellant space propulsion systems, analyse the five phases ( concept and definition, design and improvement, manufactureing and arrangement, operation and ma intenance, disposal ) in which life cycle cost of liquid propellant space propulsion systems is cost separately, then discompsed structure of life cycle cost and model of life cycle cost are presented

    將組件分成氣路組件和液路組件，再對氣路組件和液路組件進行相應的分類，然後通過對通用流路方程進行分析和變換對不同類型的組件分別建立不同的方程，從而建立了一個適用於液體推進劑空間推進系統的靜態數學模型；根據靜態計算所得到的數據，應用統計回歸法和應力分析法分別建立推力室、推進劑、推進劑貯箱、氣體、氣瓶以及導管和活門等的質量模型，從而建立相應的質量模型；結合液體推進劑空間推進系統特點，對液體推進劑空間推進系統全壽命周期費用發生的五個階段（概念和定義、設計和改進、製造和安裝、運行和維修、處理）分別進行分析，建立了液體推進劑空間推進系統全壽命周期費用分解結構和全壽命周期費用模型。
  7. Application of partial least - squares regression on multi - dependent variable model analysis of quadratic regression design and its optimal solution

    偏最小二乘法在回歸設計多因變量建模中的應用及其優化
  8. A - optimal design for duality quadratic polynomial regression models in circle region

    圓域上的二元二次多項式回歸模型的最優設計
  9. Presents the system established by taking variable - speed torque converter with adjustable guide blades as a pilot control unit and forming an open or closed loop feedback control system, and its outstanding advantages, such as high capacity, simplicity, reliability and good transmission efficiency owned by hydrodynamic drive, and the dynamic model developed for variable - speed torque converter with adjustable guide blades by means of theoretical analysis and regression analysis of experimental data, and concluds that the model is sophisticated and simple enough to be used as a tool for design, analysis and computer simulation of a hydrodynamic control system

    以導葉可調式液力變矩器作為控制單元組成的開環或閉環液力控制系統，具有液力傳動裝置能容大、系統簡單可靠、傳動效率較高等顯著的優點.通過理論分析和試驗數據的回歸分析方法建立了導葉可調式液力變矩器的數學模型，模型既簡單，又有足夠的工程應用精度，為液力控制系統的設計、動態分析和性能預測提供了必要的理論基礎
  10. The research for method of regression analysis on the experimental design

    試驗設計中多元回歸分析方法的研究
  11. 2. systems analyzed on the design principle of near - earth orbit, regression orbit, stationary orbit, critical orbit and construction orbit. base on this, a orbit design model is given

    2 、系統研究了近地軌道、太陽同步軌道、回歸軌道、靜止軌道、臨界和凍結軌道的設計原理，在此基礎上，建立了軌道設計模型。
  12. And grindintg experiment based on uniform design is conducted. depending on data process system, the regression model of production efficiency, output per degree and particle are established. through single factor analysis on all experimental indexes, the law that the bottom corner, height, bottom length of trapezium and spacing influence the hammer mill capbility are achieved

    並採用均勻設計方法安排異型粉碎室粉碎試驗。利用數據處理系統，建立生產率、度電產量、粒度的回歸方程。對各試驗指標進行了單因素分析，研究梯形篩片的底角、高度、間距和下底長對粉碎性能的影響規律。
  13. It is important to apply influence analysis, computing of correlation - conefficient and charactrestic value of the design matrix and ridge regression to set models. the quality of model is developed

    數據分析：影響分析和設計矩陣的相關系數和特徵值計算及嶺回歸技術的應用對改進模型的品質起到了重要作用。
  14. The aim of software testing is to find out the defect of the software, so different testing methods can be adopted to design test case so as to the test is successful. for example, white box testing ( logic covering, path covering, etc ) and black box testing ( function test, regression test, and performance test, etc )

    軟體測試的目的主要是發現軟體中的缺陷，針對這一目標，可以採用不同的測試方法來設計測試用例以保證測試成功，即找出軟體中的缺陷，如白盒測試（邏輯覆蓋，路徑覆蓋等）和黑盒測試（功能測試，回歸測試，性能測試等） 。
  15. Abstract : to facilitate the design, teaching and research of asphalt pavements, the article founded the models of displacement and tensile stress of three - layer system by using separation of variables, analysis and synthesizer. based on the analysis of common pavement structures and their equivalent conversion, the regression formulas of displacement and tensile stress are obtained successfully, furthermore the formulas applied in multi - layer system are checked. a great number of results of regression formulas show good accuracy for engineering application and theory research

    文摘:為方便瀝青路面結構設計生產、教學、科研之用，本文採用分析綜合法與分離變量法建立了彈性三層體系應力位移顯式模型；並在分析常見路面結構層厚度及其當量換算和模量變化范圍的基礎上，成功求得了三層體系路表彎沉、上層滑動應力、上層連續應力、中層應力逼近公式；精度分析表明本文逼近公式精度很好，完全可推廣應用於多層體系，滿足工程設計和有關理論研究的需要
  16. The second, the launching dynamics calculation of projectile is arranged by using the theory of uniform design, and the concept of the integrating quantity for initial disturbance and the concept of the independence factor ' s effecting degree to dependence factor is inducted too. from the model of stepwise regression, the main random factors and their effecting degrees to initial disturbance can be obtained also

    第二，用均勻設計理論安排彈丸發射動力學計算，通過引入起始擾動綜合量的概念和自變量對因變量的影響程度的概念，由逐步回歸模型分析了影響彈丸起始擾動的主要因素及其對起始擾動的影響程度，並推導了由自變量的標準差計算因變量標準差的公式。
  17. And the primary and secondary relation of the factors and the optimum level of every factor were obtained as well as the best scheme of structure design in the research condition. regression equal between traction resistance and partial sphere height, bottom circle radium was set up to explore the effect of two evident factors ( height and bottom circle radium of the partial sphere ) on traction resistance by optimum calculation

    採用二次回歸試驗設計的方法，建立了球冠高度和球冠底圓半徑大小與牽引阻力間的回歸方程，進行了優化計算，進一步考察了球冠高度和球冠底圓半徑大小兩個顯著性因素對牽引阻力的影響規律。
  18. Combining with practical investigation and analysis, the author presented the fitting equation of the second non - uniform coefficient in which the method of least squares error approximation with the power index regression is used and proposed a modified formula for flow rate per second calculation to precisely determine the size of pipeline and to make the design advanced in technology and reasonable cost

    本課題分析了室外和室內的設計流量公式，通過調查、實測本地區的水量資料，運用相關數學方法分析，提出了適合小區給水管網採用的流量公式。
  19. Orthogonal polynomial regression design for interference elimination in atomic absorption spectrometry

    消除原子吸收光譜分析中干擾效應的正交多項式回歸設計
  20. Thirteen treatments with combinations of 5 levels of p and k fertilizers were arranged with regression design for each variety in the subplots ( table 2. )

    每一個品種施用磷、鉀肥各設5個水平，共13個組合處理，採用回歸設計（見表2 ） 。
分享友人
分享到 Line

分享到臉書