reinforcement plate 中文意思是什麼

reinforcement plate 解釋
補強板
  • reinforcement : n. 1. 增強，加固；補強物，強化物；補給品。2. 增援，支援；〈pl. 〉增援部隊，援軍；救援艦。
  • plate : n 1 厚金屬板 〈cf sheet〉 板（片）；（記有姓名等的金屬）牌子，（尤指醫生的）招牌，藏書牌；【印刷...
  1. This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure

    本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。
  2. Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior

    分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。
  3. At first, based on the results of in - situ load tests, the load - settle curves are acquired, and the effects of different reinforcement parameters are presented. these parameters include the linear density ratio ( ldr ) ; the location of the top layer of the geobelt measured from the bottom of the load plate ( u ) ; the different materials of geobelt ; the number of reinforcement layers ( n ) and the distance between the two layers of geobelt ( a h ). these results show that the bearing capacities of the reinforced composite foundation can be improved and the settlement can be reduced

    首先，通過現場載荷試驗，獲取了加筋墊層復合地基荷載-沉降曲線，從筋帶鋪設的密度、筋帶的首層間距、不同筋帶材料、加筋層數以及雙層筋帶的層間距等幾個方面分析了以上加筋參數對加筋復合地基承載力的影響，指出筋帶的存在提高了加筋復合地基的承載力，減小了沉降。
  4. Stock guide liner plate grid edge reinforcement structure

    導料板襯板格棱筋
  5. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  6. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  7. Application of water damage and reinforcement for base plate of flood discharge trough in spillway of guanzhuang reservoir

    官莊水庫溢洪道泄槽底板水毀原因分析與加固
  8. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  9. The results show that welding the appropriate reinforcement plate to the girder crack can eliminate crack expanding and assure crane safe operation

    結果表明，採用參數適當的補強板，可降低起重機主梁裂紋尖端的應力，從而保證起重機的安全。
  10. Using the ansys finite element analysis software, this paper analyzes reinforcement plate of different length welded to crane girder crack and find out the girder ' s stress and deformation

    摘要採用ansys有限元分析軟體，對因出現裂紋的起重機主梁而添加的補強板進行系列計算，得出修補後主梁裂紋的應力及應力強度因子的變化規律。
  11. Cause analysis of flange plate shear fracture and reinforcement plan selection of a t beam bridge

    梁橋翼緣剪切斷裂原因分析與加固方案選擇
  12. In this paper, the reinforcement method with steel plate adhering to a real queen - post girder in bridge was analyzed by using the space entity simulation model, and the effect was validated by load test on site

    摘要針對某座橋梁下部結構蓋梁採用粘鋼法進行加固，對其加固效果採用有限元模型進行模擬分析計算，並通過現場荷載試驗進行驗證。
  13. Analysis and evaluation of the reinforcement effect of steel plate adhering to the queen - post girder

    蓋梁粘鋼法加固的效果分析評價
  14. The main contents of the research : the material ' s property in reinforced concrete structure with corroding reinforcement and an experimental study on concrete roof plate ' s bearing capacity with corroding reinforcement and later into rating concrete

    本課題主要研究內容是：鋼筋混凝土結構鋼筋銹蝕后材料性能研究；鋼筋銹蝕和混凝土破損屋面板承載力試驗研究。
  15. The steel plate and pipe network infrastructure, but they should pay attention to the ministry of negative reinforcement plate to prevent fall into

    板的鋼筋網綁扎與基礎相同，但應注意板上部的負筋，要防止被踩下
分享友人
分享到 Line

分享到臉書