reinforcement strength 中文意思是什麼

reinforcement strength 解釋
補強強度
  • reinforcement : n. 1. 增強，加固；補強物，強化物；補給品。2. 增援，支援；〈pl. 〉增援部隊，援軍；救援艦。
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. To improve the binding strength between the deck slabs and deck surfacing layer of badong changjiang river highway bridge and to provide the surfacing layer with anti - cracking ductility, a series of technical measures has been taken in the construction of the deck surfacing of the bridge, including those of embedding binding reinforcement in the deck slabs, spraying inorganic binding agent between the slabs and layer, replacing part of the cement with micro expansion agent and adding appropriate amount of polypropylene fibers to the concrete

    摘要巴東長江公路大橋橋面鋪裝，通過採取預埋橋面粘接鋼筋、噴塗無機界面粘結劑、用微膨脹劑替代部分水泥、在混凝土中摻入適量的聚丙烯纖維等措施來提高橋面板與鋪裝層間的界面粘結強度和給橋面抗裂增韌。
  2. Methods of test for ancillary components for masonry - determination of bond strength of prefabricated bed joint reinforcement in mortar joints

    圬工輔助砌塊的試驗方法.灰漿連接處預制基地接合處加固的粘結強度的測定
  3. Reliability assessment of xi - luo - du underground water - power plant : the results have been used by the cheng - du surveying, design and research institute for the preliminary design ; （ 2 ） the stress and strain analysis for the xiao - guan - zi sluice and its foundation : the report has been applied for the reinforcement of the foundation ; （ 3 ） the thermal control procedure for the no. 7 - 14 power plant dam segments of the three gorge project ： the research report provides the effective and efficient methods for the controlling of the temperature field in the mass concrete structure ; （ 4 ） the software system development for the long - term monitoring for dikes ： the software can automatically give the results of the seepage field and the probability of soil piping of dikes and underground ; （ 5 ） reliability assessment of xiang - jia - ba underground water - power plant : the results have been used by the zhong - nan surveying, design and research institute for the preliminary design ； （ 6 ） fatigue reliability estimation of shipping berthing pillar : the results give the optimized design scheme and prediction of the structural age ; （ 7 ） 3 - d static and dynamic stochastic finite element analysis for the strength, stability and thermal control problem for xi - luo - du project

    溪洛渡水電站超大型地下洞室群圍巖穩定的安全可靠性分析：被成都勘測設計研究院應用於比選報告及可行性論證中； （ 2 ）小關子水電站攔河閘壩及地基的應力應變分析：被成都勘測設計研究院應用於地基加固處理方案； （ 3 ）三峽廠房7 # - 14 #壩段溫控並縫措施研究：為廠房壩段並縫方案的可行性提供了依據； （ 4 ）堤防工程體系的長期監控預報預警決策系統開發：為監控、預測預報堤防滲漏管涌破壞提供分析軟體； （ 5 ）向家壩地下洞室群圍巖穩定的安全可靠性分析：被中南勘測設計研究院應用於初步設計方案中； （ 6 ）靠船墩的疲勞可靠度研究：為廣東航運規劃設計院的靠船墩優化設計和加固提供依據； （ 7 ）溪洛渡高拱壩壩體壩基（壩肩）強度和穩定的三維靜動力隨機有限元分析及可靠度計算：為溪洛渡重大工程壩體的靜動力安全穩定性及溫控方案提供依據。
  4. In this paper, high strength micro - expansive lightweight aggregate concrete is compounded successfully and it is firstly applied to the reinforcement of arch ring which is reference to the further compound and usability of lightweight aggregate concrete

    本文的研究成功地配製了高強度輕質砼，並將輕質砼首次應用於拱橋主拱圈加固，對輕質砼的進一步配製以及廣泛應用具有參考價值。
  5. It shows that the method suggested in the paper is simple, applicable for engineering and has good precision. on the bases of the formulas deduced, and combining with relative test datas, it studies in the paper several factors influencing the bearing performance of the simple beams, such as shape of the external tendons, the equal moment segment length, span - to - depth ratio of the beam, valid initial prestress of the external tendons, area of the internal tension reinforcement, strength of the concrete, vertical distance between

    在公式推導的基礎上，結合相關試驗資料，研究了體外筋的形狀、等彎矩區長度、梁跨高比、有效張拉預應力、體內受拉筋配筋率、混凝土強度、錨固點到樑上邊緣在垂直方向上的距離、體外預應力筋水平段長度（雙折線型體外筋的情況）以及荷載類型等對體外預應力混凝土簡支梁受力性能的影響。
  6. Study on strength property of nanometer silica fume reinforced cemented soil and reinforcement mechanism

    納米硅粉水泥土的強度特性及固化機理研究
  7. Available empirical results indicate that the creep of reinforcement strongly influences the overall behavior of rs structures, which is demonstrated by excessive deformations. different creep tests are discussed and the test methods to obtain the two kinds of creep curves are compared in this thesis. the methods of how to determine the reduction factor according to long - term strength of creep or allowable strain during the services life are presented

    文中介紹和研究了不同的蠕變試驗手段，比較了獲得兩種蠕變曲線的試驗方法，並給出了兩種蠕變曲線一定范圍外推的數據處理方法;給出怎樣根據設計使用年限的長期蠕變強度或容許應變來確定蠕變折減系數的方法，並用計算實例來說明。
  8. The use of steel reinforcement with structures of this type greatly increases their strength.

    這種類型結構物使用鋼筋加固后大大增加其強度。
  9. Determination of shear strength of welded joints of reinforcement mats or cages for prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure

    高壓充氣混凝土或敞開結構輕型聚集混凝土預製件用加筋氈或框架的焊縫剪切強度測定
  10. According to the geometrical characteristics of the surface on the deformed bars, considering the interfacial properties of the corrosion reinforcement and concrete, such as the microscopic mechanics model of corroded reinforcement ribs, the deterioration of ribs on the bearing surface of the deformed bars after corrosion and the effect of corrosion products of corrosion reinforced bar on the bond strength, and analyzing the distribution and interaction of the forces on the surface of the corrosion reinforcement and concrete, the calculation expressions of the bond strength between corroded deformed bars and concrete with and without transverse steel are established

    從變形鋼筋的表面幾何特徵出發，考慮了鋼筋銹蝕后鋼筋與混凝土接觸面的特徵，例如鋼筋橫肋在銹蝕狀態下的細觀力學模型，鋼筋銹蝕后鋼筋橫肋高度的變化和銹蝕產物的生成對粘結力的影響。通過分析接觸面上各種力的分佈形式及相互關系，建立了有橫向鋼筋和無橫向鋼筋約束作用下，鋼筋與混凝土之間粘結力的計算表達式，且與相關文獻的結果進行了比較。
  11. The principal conclusions include : ( a ) the composite system is composed of both active - bearing structural members and inactive - bearing ones, being of a character of combination of rigid retaining structures with flexible ones, so its working mechanism will be behaved as sharing loadings, waterproof and impermeability, loading transfer, local reinforcement and pre - reinforcement ; ( b ) the experimental results show that much more subsoil will participate in retaining action, soil stresses of internal slope will be shared uniformly and deflections caused by excavation will be reduced notably because of cooperation of nails and cement - soil mixing pile wall ; and ( c ) the internal forces of facing in vertical model will be a control factor of design and the cross section tensile strength of cement - soil wall will govern strength of the

    主要研究結論有： （ 1 ）復合土釘支護的作用機理主要為臨時加固土體以保證局部穩定、有機聯系以共同承擔荷載、改善土體性質起到止水抗滲作用。 （ 2 ）試驗結果表明：復合土釘支護能夠充分調動周圍土體共同作用，有效地控制基坑變形；復合土釘支護中止水帷幕的插入深度和強度對控制邊坡變形與失穩有較大作用；復合土釘支護效果明顯優於一般的土釘支護。 （ 3 ）面層與邊坡土體共同變形，設計時可按外力作用下的彈性地基梁進行計算。
  12. Specimens ’ cracking load under dead - load, fatigue failure characteristic, fatigue life, deflection of span - centre, fatigue flexural rigidity, maximal crack width, development of cracks and strain of concrete and steel bars have been investigated. the influence of fatigue cycle characteristic, ratio of reinforcement, kinds of aggregate and concrete compressive strength on the specimens ’ fatigue behavior has been also investigated

    對試件的靜載下開裂荷載、疲勞破壞特徵、疲勞壽命、疲勞荷載作用下的跨中撓度、截面疲勞抗彎剛度、裂縫開展情況及最大裂縫寬度、鋼筋及混凝土在循環荷載作用下應變等內容進行了研究，分析了疲勞循環特徵值、縱筋配筋率、骨料種類、混凝土抗壓強度等因素對試件疲勞性能的影響。
  13. According to the reinforcement mechanism, some experimental phenomena and rules in the strength tests of cemented soil and cemented stone are explained

    根據固化機理，解釋了水泥土和水泥石強度試驗中的一些現象和規律，分析了納米硅粉改性水泥土的適用性。
  14. Six circular concrete columns were tested under concentric loading, to investigate the confinement effect of confining reinforcement in both normal strength and high strength concrete columns. test results were analyzed and compared. practical formulas were proposed for the minimum volumetric ratio and the spacing of the stirrups

    通過對6根圓柱體混凝土柱的軸壓試驗，研究普通混凝土及高強混凝土在箍筋作用下的約束效應，並將試驗結果進行分析比較，提出了配箍率及箍筋間距實用計算公式。
  15. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  16. In this thesis, based on the theories of corrosion expansion force and the elasticity, by adopting the theory of reinforced concrete structures, the durability problems of reinforcing concrete structures considering the corrosion of reinforcing bar are studied systematically, such as the change of steel mechanical properties, the bond strength between corroded reinforcement and concrete, the shear carrying capacity and the flexural carrying capacity of the corroded reinforced concrete ( rc ) structural elements

    本論文以鋼筋混凝土構件為研究對象，基於銹脹力研究理論和彈性力學，採用鋼筋混凝土結構基本原理，系統地研究了鋼筋銹蝕后鋼筋混凝土結構的耐久性問題，例如鋼筋的力學性能，銹蝕鋼筋與混凝土之間的粘結強度，剪切強度，抗彎強度等。
  17. Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model

    到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。
  18. According to author ' s practical experience accumulated in many years of water project construction, the author gives brief description to some common quality defects in cast - in - site concrete construction, such as honeycomb, ballast - surface, holes, reinforcement emerging, crack, surface unevenness, insufficient strength etc

    根據在水利水電工程施工中多年積累的實踐經驗，簡要闡述了現澆混凝土施工中常見的一些質量缺陷，如混凝土出現蜂窩、麻面、孔洞、露筋、裂縫、表面不平整、強度偏低等。
  19. With the prerequisite of meeting requirement of its working performance, the mix design of common grades can be concluded though strength test if we check various property of the said concrete with the certain mix design, such as compressive strength, tensile strength, elastic modulus, reinforcement wrapping strength, leakage resistance, shrink property and charring resistance, and compare them with property of ordinary concrete, we will find that the various dynamic property of self - densifying high performance concrete is very satisfactory and the durability is quite ideal

    在滿足自密實高性能混凝土工作性能的前提下，通過強度試驗得出常用強度等級混凝土的配合比，檢測該配合比下的自密實高性能混凝土的抗壓強度、劈裂抗拉強度、彈性模量、鋼筋握裹力性能、抗滲性、收縮性、抗炭化性等性能，以及各種性能與普通混凝土的比較，驗證自密實高性能混凝土硬化后的各方面力學性能是完全能夠符合要求的，並且具有較高的耐久性。
  20. In order to reveal load mechanism and failure mode of thick pile caps, by means of the test of 1 / 4 - scale models of thick pile caps with six piles and post - handling study of 3 - dimensional non - linear finite element adina, this paper points out the shortage, which is that the design of pile caps is carried out by flexural strength in chinese technical code for building pile foundations jgj94 - 94 and american reinforcement concrete building construction code aci318 - 02, promulgates that the failure mode of thick pile caps is punching failure and load transfer mechanism is the strut - and - tie, which is that zones of concrete with primarily unidirectional compressive stresses are modeled by compress struts, while tension ties are used to model longitudinal reinforcement over pile

    摘要為揭示厚承臺的傳力機理和破壞形式，通過對4個1 : 5比例的六樁厚承臺的模型試驗研究與三維非線性有限元adina的后處理研究，指出中國建築樁基技術規范jgj94 - 94與美國鋼筋砼房屋建築規范aci318 - 02規范中，承臺以彎曲強度進行配筋計算的設計方法之不足，揭示出厚承臺的破壞模式是沖切破壞，傳力機理是以帶有主要單向壓應力的砼區域作斜壓桿，樁頂區域的縱筋作拉桿的空間桁架。
分享友人
分享到 Line

分享到臉書