required thickness 中文意思是什麼

required thickness 解釋
要求厚度
  • required : adj. 〈美國〉必修的（大學課程）。
  • thickness : n 1 厚；粗；厚度；粗大。2 濃度，濃厚，黏稠。3 密度；稠密。4 模糊不清，多煙霧，混濁。5 愚笨；遲鈍...
  1. The geometrical variables of the fiber and resin types may be varied to reach the required mechanical properties. the model includes all the important parameters that influence the mechanical behavior : the lamina thickness, the yarn orientation, the fiber volume fraction and the mechanical characteristics of the components

    通過這種方法建立的模型應包含所有影響編織復合材料力學行為的重要因素：板的厚度、編織方向、纖維體積比等幾何參數以及材料的力學性能參數。
  2. Construction of the formwork and preparation of the metal reinforcement for shells required particular care and accuracy because of their limited thickness.

    由於殼體的厚度有限，殼體的金屬能加工制備與模板建造需要特別細心與精確。
  3. Damp earth may be expected to act in a similar manner, although about 50 percent greater thickness would be required.

    預期濕土也能起到同樣的作用，不過這時厚度約需增加50。
  4. Damp earth may be expected to act in a similar manner, although about 50 percent greater thickness would be required

    預期濕土也能起到同樣的作用，不過這時厚度約需增加50 。
  5. If the paint becomes too thick ( e. g. in cold weather ) or low film thickness is required ( e. g. sealer ), thinners in product data sheet can be used during application to obtain good performances

    如果油漆變得過稠（如：天氣寒冷）或要求的漆膜厚度很低（如：封閉漆）可在施工時採用產品說明書上指明的稀釋劑適當調配，以取得良好的效果。
  6. The viberating roller keeps on the ground and viberates horizontally ， getting the required compaited thickness more quickly

    振蕩輪始終接觸地面，作水平振蕩，能更快地連到要求的壓實度。
  7. If the required coating thickness has not been achieved, it should be touched up with airless spray or with brush or roller

    如果未達到要求的厚度，應通過無空氣噴塗、刷塗或滾塗補塗至規定膜厚。
  8. In order to - obtain the required thickness a number of sheets of pieces of cloth were glued together

    為了達到必要的厚度，需要用膠水把數片薄布粘合起來。
  9. To design thickness of ballast bed is based on the required strength of track structure and partly the experience in national railway

    現行的地鐵設計規?對道床厚度的選擇僅根據軌道強度要求和國鐵的經驗確定。
  10. Fluid flow pipe wall thickness required

    流體流動管壁厚的要求
  11. Experimentalresults showed that the thickness of the frp interface stress has importantimplications in the use of intensity required to achieve such a way as to not morethan three layers, because in temperature 40 degrees, the stress arising from theinterface sheared intensity has reached half

    實驗結果表明， frp片材的厚度對界面的應力有著重要的影響，在補強強度達到使用要求的情況下，盡量不要超過3層，因為在溫差40時，三層碳纖維補強所產生的界面應力已達到界面剪切強度的一半。
  12. In the present dissertation, the densification mechanisms and the structure controlling of various transient layers of w - mo - ti flier - plates with graded wave impedance were mainly investigated. wholly dense w - mo - ti flier - plates were then prepared by powder stacking and hot - pressing. in order to achieve a required wave impedance profile and a quasi - continuous change along the thickness direction, the ratios of components in transient layers were well adjusted

    論文採用粉末冶金方法，詳細研究了w - mo - ti體系梯度飛片材料中各組元的燒結緻密化機理與控制方法，以精細控制不同配比的混合粉末的鋪填方式與鋪填結構來減小梯度飛片材料內部波阻抗值的躍變幅度，成功制備出波阻抗按指定分佈特徵沿厚度方向準連續變化的、波阻抗面平行度高並且整體緻密的w - mo - ti體系梯度飛片。
  13. In chapter three, the momentum integral equations and their solutions of two - phase fluids in boundary layer are given and the no - disturbance solutions on the surface of vane are required. leading into the disturbance factor of no - dimension and thickness coefficient ks in boundary layer, the numerical method of finite approximation is used to calculate the boundary layer

    第三章給出了固液兩相流泵的邊界層動量積分方程及其解的一般表達式，並得到葉片表面的無擾動解；引入了無量綱擾動因子及邊界層厚度系數k _ ，給出了用於邊界層計算的有限次逼近的計算方法。
  14. In view of smaller and thinner samples required in grinding slice for microprobe analysis, three steps are used : establishing a thinner grinding plane on the center of homogenized crystalloid melt inclusion sample, grinding the surrounding parts of the sample to the thickness as the center, polishing the grinded sample slice in order to expose the melt inclusion to the sample surface

    摘要針對磨製樣品十分細小和較薄等特點，採用如下三個步驟磨製：以加熱過的細小樣品為中心創建一磨製平面；將樣品周圍的巖石薄塊磨至接近細小樣品的相同厚度；在拋光機上拋光，使包裹體完全露出表現。
  15. When the slip has time to set the required thickness, the surplus away

    當泥漿凝固到所需厚度時，把餘下泥漿倒出。
  16. Besides, when the field with thin electrode is solved by the use of conventional csm, the discrete charges are required putting inside the electrode, but it is impossible for the electrode with thinnest thickness

    傳統csm在處理薄電極問題時，要求離散電荷布置在電極內部，而這對于厚度極薄的電極來說是不可能的。
  17. If the required paint film thickness has not been achieved, the additional coats should be applied till the specified thickness is attained

    如果未達到要求的濕膜厚度，應覆塗直到滿足指定的濕膜厚。
分享友人
分享到 Line

分享到臉書