resin content 中文意思是什麼
resin content
解釋
膠含量,樹脂含量-
A detailed introduction was made to the properties of the wet coated sand suitable for multi - station shell mould shooting machine ; the development of a sort of high strength coated sand with low resin content : the shaping index and wetness adjusting process : analysis and prevention of peel back defect of shells made with overturning hopper process ; test method of peel back resistance of coated sand : pinhole defect analysis of high ni ductile iron shell mould castings and application of anti - pinhole coated sand
詳細介紹適用於吹砂式多工位殼型機的濕態覆膜砂性能；高強度低樹脂量覆膜砂的研製；濕態殼型覆膜砂的成形性指數與調濕工藝；翻鬥法制殼時的脫殼問題分析和解決辦法；覆膜砂脫殼性檢測方法；高鎳球鐵件殼型鑄造表面針孔原因分析與抗針孔覆膜砂的應用。 -
3. based on the gel time and dsc curve figure of two kinds of modified phenolic resin and flory and kissinger theory, the rage of cure process parameters for the resin system, moulding pressure and resin content are established
3 、通過對二種改性酚醛樹脂體系凝膠時間、 dsc曲線圖的分析，引入flory理論、 kissinger理論，確定了樹脂體系的固化工藝參數（固化溫度、固化時間、后處理溫度）范圍；並初步確定了成型壓力和樹脂含量的范圍。 -
Dsc for the nanocomposites showed the glass transition temperature ( tg ) of the nanocomposites increases slightly as the mmt content increases. water absorption velocity and water retentivity under pressure tests showed the addition of montmorillonite ( mmt ) can improve the beginning absorption velocity and water retentivity for pure superabsorbent resin
吸水速率和加壓保水能力測試表明，一維納米級蒙脫土片層的引入能在一定程度上提高高吸水性樹脂的初期吸水速度和加壓下的保水能力。 -
Wood pulp board for viscose fiber. determination of resin content
粘膠纖維用木漿粕樹脂含量的測定 -
The analysis of fluorocarbon resin content in fluorocarbon lacquer by using oxygen bomb burning method with fluorin ion electrode are discussed in detail
摘要採用氧彈燃燒法配合氟離子電極對有機濃劑型和水溶性氟碳漆中氟碳樹脂含量的分析方法進行了研究。 -
Using non - saturable polyester resin as its basal masal and unidirectional fiberglass woven fabrics as its skel eton, the frp pole is taken shape by ce - ntrifugal kr twine forming process and has high axial strength and its content if fiberglass is over 50 %. the frp light pole
Frp燈桿系採用不飽和聚酯樹脂為基材，以單向布為主的玻璃纖維織物為骨架，採用離必成型工藝或發纖維骨架通過纏繞成型工藝製作而成，玻璃纖維含量在家50 %以上，軸向強度很高。 -
Resin finishing agent - determination of the nonvolatile content
樹脂整理劑中不揮發組分的測定方法 -
Determination of the resin content in friction material reinforced by fiber
纖維增強摩阻材料中樹脂含量的確定 -
Test method for resin content of glass
玻璃纖維增強塑料樹脂含量試驗方法 -
Test method for resin content of carbon
碳纖維增強塑料樹脂含量試驗方法 -
Test method for resin content of prepreg
預浸料樹脂含量試驗方法 -
Test method for resin content of carbon fiber reinforced plastics
碳纖維增強塑料樹脂含量試驗方法 -
Test method for resin content of glass fiber reinforced plastics
玻璃纖維增強塑料樹脂含量試驗方法 -
Test method for physical properties of composite material prepreg part 5 : determination of resin content
復合材料預浸料物理性能試驗方法第5部分:樹脂含量的測定 -
How does the supplier control resin content
如何控制樹脂砂含量？ -
Under the same conditions of hot - pressing time, composite density, pe ratio, and resin content, the optimum properties of the composites can be obtained when hot - pressing temperature is 190 degrees c
當在熱壓時間、聚乙烯比例、施膠量、復合材料密度相同的條件下，熱壓溫度為190時壓制出的麥秸聚乙烯復合板材各項物理力學性能較好。 -
Plastics - phenolic moulding materials - determination of acetone - soluble matter apparent resin content of material in the unmoulded state
塑料.酚制模材料.丙酮可溶性物質測定 -
Plastics. phenolic moulding materials. determination of acetone - soluble matter apparent resin content of material in the unmoulded state
塑料製品.酚醛模製材料.丙酮可溶物質的測定 -
Methods of testing plastics - glass reinforced plastics - determination of volatile matter and resin content of synthetic resin - impregnated textile glass fabric
塑料試驗方法.第10部分:玻璃纖維增強塑料.試驗方法1006 :合成樹脂浸漬玻璃纖維織物中揮發物和樹脂含量測定 -
Research of influence factors on phenolic resin content of coat mix powders
包混粉體中酚醛樹脂含量的影響因素研究
分享友人