ring lubrication 中文意思是什麼
ring lubrication
解釋
鋼領潤滑- ring : n 1 圈，環，輪；戒指，指環，耳環，鼻圈，鐲子（等）；【運】吊環。2 輪狀物；【植物；植物學】年輪；...
- lubrication : n. 潤滑，油潤，上油；潤滑作用。 lubrication groove 油槽。 ring lubrication油環潤滑法。
-
Lubrication ring for driving shaft
傳動軸潤滑環 -
Scuffing failure of piston ring - cylinder liner in liquid - solid lubrication
自潤滑軸承在煉鐵廠托輥中應用的試驗研究 -
Ring lubrication bearing
環圈潤滑軸承 -
Detga - a sereies of bearing and circulating oils. manufactured from high viscosity index paraffinic base oils, prssessing excellent natural demulsificationnproperties. effective additives further enhance oxidation stability. recommended for applications where the extra load carrying characteristics are not required. suitable for lubrication of machine guides, bearings and spindies, aie line lubrication of maching tools, ring liled and wick feed bearings, and light duty gear and hydraulic systems
德佳-一系列軸承及循環系統油，由高粘度指數石蠟烴基礎油製造，具有極佳之天然抗乳化性，有效的添加劑提高了抗氧化性能，特別推薦于輕度負荷的操作，可應用在機床導件、軸承、錠子、氣動件潤滑、油環及油繩潤滑軸承等，甚至是輕負荷及液壓系統。 -
Based on reynolds equation and solid particles carrying model, a theoretical model for piston ring - cylinder liner lubrication in liquid - solid lubrication had been proposed. the effect of solid particles " diameter and concentration are introduced in the model. the influence of the particles " diameter and concentration on load, film thickness and friction force had been analyzed
基於reynolds方程及顆粒承載模型，引入顆粒直徑、濃度等參數，並建立了分析液固二相潤滑下活塞環?缸套摩擦副潤滑狀態的模型，探討了不同顆粒直徑和濃度對承載、油膜厚度及摩擦力的影響。 -
Based on an experiment performed on the piston ring - cylinder bore wear tester, liquid - solid lubrication is investigated in this thesis. the wear of the samples under different lubrication conditions ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight ) are discussed. the variations of the surface topography, especially the statistical parameters and functional parameters are studied, and the reasons that cause the variations are analysed
本研究基於活塞環-缸套摩擦磨損臺架實驗研究了液-固二相流體潤滑的問題，探討了潤滑油中不含固體顆粒、含有0 . 02和0 . 1納米顆粒三種潤滑狀態下的磨損情況，並進一步研究了液-固二相流體潤滑狀態下試件表面形貌特性的變化，主要是統計參數和功能參數的變化，並探討了引起變化的原因，為更深入的液-固二相流體潤滑問題的研究以及表面形貌設計提供理論上的參考。 -
The signal processing software was developed by vc + + tools. the modules of the software including board controlling, signal input, data saving, figure display, statistic computing, filter design, spectrum analysis, etc. based on the experiment performed on the piston ring - cylinder bore wear tester, the friction force and max scuffing load under different liquid - solid lubrication ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight, the type of particles are mos2 and udp ) is investigated in this thesis
然後，以內燃機中的活塞環-缸套摩擦副為目標，在活塞環-缸套摩擦副實驗臺架上進行模擬實驗，考察在不同二相流潤滑（潤滑油分別為純潤滑油、含納米級金剛石粉（ udp ） 、二硫化鉬粉（ mos _ 2 ）的濃度為0 . 02和0 . 1的液-固二相潤滑油）條件下摩擦副的摩擦力及極限擦傷載荷的變化。 -
05. 02 wear preventive properties of lubrication greases using the ring and block test machine in oscillating motion, test for
在震蕩運動中用潤滑劑耐熱耐壓試驗機測定潤滑脂的耐磨損特性的試驗 -
Liquid ring technology - pressure vacuum pump - a vacuum or pressure pump requires no lubrication. for use in oil and gas industry
-為化肥化工石油煤碳軍工塑料建材等行業提供大型壓縮機。 -
It presents three types of friction between parts of the engine ( complete fluid friction, edge friction and half dry friction, dry friction ) and renault equation, and sets forth the friction and the lubrication of cam - driven parts, crankshaft, piston and piston ring. also it shows the forecast technique of the friction losing in designing engine
介紹了發動機零部件間的三種摩擦狀態（完全液體摩擦、邊界摩擦和半干摩擦及干摩擦）和雷諾方程，闡述了凸輪?從動件、曲軸、活塞及活塞環的摩擦和潤滑，並給出了發動機設計時摩擦損失的預測方法。
分享友人