roll gap 中文意思是什麼

roll gap 解釋
輥間距離
  • roll : vt 1 滾，轉，推滾（桶、車輪等），使（煙、塵土）滾滾上升，滾滾推進（浪、水等）；滾動，溜轉（眼睛）...
  • gap : n 1 （墻壁、籬笆等的）裂口，裂縫；豁口，缺口。 【軍事】突破口。2 （意見的）齟齬，分歧；隔閡，距離...
  1. Photoelectric roll gap measuring instrument

    光電式輥縫測量儀
  2. Study on factors affecting roll gap in the rolling process and model design

    軋鋼過程中影響輥縫的因素研究及模型設計
  3. Theoretically the varying contact rolling technology can increase the transverse stiffness of loaded roll gap, heighten the control effect of roll bending, improve the distribution of contact force between backup roll and work roll

    從理論上分析了變接觸軋制技術在提高承載輥縫橫向剛度、增加彎輥力調控功效、改善輥間接觸壓力分佈方面的作用。
  4. The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other

    可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。
  5. With the help of the theoretical equation of rolling and the energy criterion of mechanical vibration, and on the base of full consideration of roll gap nonlinearity during vibration, this paper suggests an approach to analyse the stability of self - excited vertical vibraiton of high speed cold strip mills by numerical method

    摘要本文在充分考慮軋機垂直振動過程中輥縫非線性的基礎上，利用軋制理論方程和機械振動理論中的能量判據，給出了更精確的分析高速冷軋機垂直自激振動穩定性的數值計算方法。
  6. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  7. The side platens are split so that they follow the contour of the front roll when changing the nip - gap

    擋板被分割成兩半，這樣在改變間隙時可以包覆著輥面而相應運動。
  8. The hand wheel is linked to the front roll via heavy - duty gears so that the nip - gap can be easily adjusted even while running a heavy compound

    手輪通過高堅固的齒輪連接到前輥，即便是開煉大量橡膠也可以輕松調節。
  9. Hsiang, s. h. and m. kiuchi, " limit analysis of asymmetrical rolling simulation of deformation behaviour of plate of asymmetrical roll - gap, " fourteenth north american manufacturing research conference proceeding, pp. 348 - 354 ( 1986 )

    向四海、黃庭彬，鍛造加工中材料流動模擬與成形負荷預估，中國機械工程學會第三屆學術研討會，第915 - 921頁（ 1986 ） 。
分享友人
分享到 Line

分享到臉書