rolling rate 中文意思是什麼
rolling rate
解釋
軋機生產率-
Two or three masks strove to knock his moccoletto out of his hand ; but albert, a first - rate pugilist, sent them rolling in the street, one after the other, and continued his course towards the church of san giacomo
有兩三個戴面具的人想來撞落他手中的長生燭，但阿爾貝可是個一流的掌術家，他把他們一個個的打發到街上去打滾了，然後奪路向聖甲珂摩教堂走去。 -
Rolling - cutting biscuit shaping machine is new equipment of making soda biscuit, good toughness of thin biscuit and super - thin biscuit. it ' s high production efficiency, low noises, safe operation, convenient, beautiful outer shape. this machine can press and roll rough flour 3 times and equiped with remaining flour recycling machine, also equiped with double - rolling cutting shaped equipement, in the mean time, it can produce two biscuit embryo of differnt shape. 3 times pressing - rolling machine can adjust different thickness and biscuit rough surface. it can roll rough flour and do not stick to rough flour embryo, correctness rate of adopting mould to cut margin of flour embryo reaches 100 percent so that avoid deforming of embryo due to deviation. this machine is one equipment which adopting advanced and won first technical rewarding for its independently control operation, beautiful outer appearance
滾切式餅干成型機是連續製作梳打餅、韌性和薄餅超薄餅的新型設備，具有生產效率高、噪音低，操作安全、方便，外型美觀等優點，本機具有三道軋輥制皮和余料回收機，配備雙滾切成型裝置，同時能生產兩種不同形狀的餅干胚不停機，三道軋輥能同時調節不同厚度和餅皮具有軋輥不粘皮、採用印模切邊一次同步進行準確率100 % ，避免偏差而造成餅胚變形，該機具有獨立控制操作，外形美觀，是目前國內較先進而獲得技術一等獎的設備。 -
In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high
針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。 -
Four contact state depending on rate of rolling / sliding between the couple of contact element were studied based on hertz contact model, and the results was shown that the rate of slide would affect the distribution of pressure in contact area and stress in the half plane
研究表明安定狀態隨載荷的大小而變化，其殘余應力和應變累積的大小與外加載荷成正比，並對計算中的一些問題進行了分析探討。 -
They were very large, so large indeed, that they had belonged to her mother, and the poor little creature had lost them in running across the street to avoid two carriages, that were rolling along at a terrible rate
鞋太大，的確大，是屬於她母親的；而且這可憐的小女孩兒橫過街道時，為了躲避飛奔過來的馬車，把它跑丟了。 -
It can improve minus deviation rolling rate greatly, assure the quality of product and increase the benefit, so it is used widely in steel rolling
採用這種軋機可以大幅度提高負偏差軋制率，穩定產品質量，提高經濟效益，因而被廣泛用於軋鋼生產中。 -
In this dissertation, the experimental study of rolling condition on two - phase flow instabilities of the forced - single - tube circulation system was carried out. furthermore, based on the d - partition method and the hypothesis of drift flow model, given some conservative equation, using the perturbation method the response of the pressure drop of the tube to the inlet flow rate perturbation was analyzed both in rolling condition and in normal upright position
本文主要通過實驗對搖擺條件對單管強迫循環中汽液兩相流動不穩定性的影響，同時在d分區法的前提下，在兩相區基於漂移流模型，一定的守恆條件下，在搖擺和不搖擺工況中用線性小擾動法對實驗段的壓降對入口流速的擾動的響應進行了分析。 -
Specially, in recent years, it has realized the roller change quickly and the main - drive system, the two level automation reformed successfully. on this condition, it realized the technology optimization, increased the task rate of unit and production quality, expanded the rolling kind and specification, and got the significant economic effects
特別是近幾年來快速換輥和主傳動系統、兩級自動化改造成功，並在此基礎上實現了工藝優化，使軋機作業率、產品質量有了明顯提高，軋製品種和規格有了擴展，經濟效益顯著。 -
For hot rolling steel production, the condition on site is poor, temperature measurement is restricted by transmitting rate, background radiation and transmission loss of optical route
對現場條件比較惡劣的熱軋生產，它的測溫受到發射率、背景輻射、光路傳輸損失等因素的制約。 -
Large sized coolant cleaner ( oil separator ) with a flow rate of 1200 l / h for application in aluminium hot rolling process with coolant tanks of up to 300 ’ 000 litres
每小時1200公升大尺寸的冷卻洗滌器適用在冷卻槽大於300 ， 000公升的熱鋁滾動加工冷卻洗滌器
分享友人