rotational temperature 中文意思是什麼

rotational temperature 解釋
轉動溫度
  • rotational : adj. 1. 旋轉的；輪流的，循環的。2. 【農業】輪作的。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar

    研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。
  2. Compress disk is the very important rotational component in the areoengine. when the compress disk is working, the grads of temperature and stress between the rim and the center of the disk are great. in order to raise the thrust - weight ratio of the disk and reduce oil consumption. the best prospective way is the dual alloys disk used

    壓氣機盤是航空發動機上一個很重要的轉動部件，壓氣機盤工作時，輪緣和輪轂溫度梯度和應力梯度較大，為了提高飛機發動機推重比、減低耗油量，要求壓氣機盤的工作溫度、使用性能更高，雙合金盤製造是最有發展前景的技術。
  3. Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed

    本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。
  4. Determination of viscosity - temperature charts for crude oil with rotational viscometers

    原油粘溫曲線的確定.旋轉粘度計法
  5. The result of the calculation for tip clearance is reasonable when it is compared with theory. two ways are put forward for convention of dimension of the turbine components from high temperature to low one, which is related with tip clearance, a simple example is used to illuminate that the two ways are useful, using the method of design optimization, axiisk and a blade of a certain turhine is analysed, it showes that the method of design optimization is feasible to be used for convertion of dimension of the turbine components. finally, ansys software is used to analyzed the variation of tip clearance with the method of cyclic symmetry analysis when engine works under the conditions of temperature and rotational speed, am using a new method to deal with thermal contact resistance in the calculation

    本文完善了計算渦輪葉尖間隙的簡化演算法程序，增加了程序的計算功能，並將其應用於某高壓渦輪進行葉尖間隙分析，所得結果與理論結果進行了對比，得出修改後的程序用於葉尖間隙計算是合理的；同時提出了與葉尖間隙相關的渦輪典型部件的冷、熱態的尺寸兩種換算方法，使用優化設計的方法進行了實例分析，說明了所提出的計算方法是可行的；最後應用ansys有限元軟體利用循環對稱的方法分析了某型發動機高壓渦輪在溫度場及離心力作用下的葉尖間隙在發動機工作過程中變化情況，並分析了計算中的接觸熱阻的處理問題。
  6. For solving the problem of insufficient temperature drop, adopts some improvement measures including relocating filling materials, adjusting the rotational speed rate of the fans, increasing the fan blade quantity and using wider fan blades

    摘要針對冷卻塔降溫效果較差問題，採取了重新碼放填料、調整風機轉速比、增加風機葉片數量、加寬葉片直徑等改進措施。
  7. And the inner temperature of lvc is also measured and the correlations under different rotational speeds, viscosity and original filling rate are given

    總之，本文所設計的液體粘性聯軸器可以實現粘性剪切和駝峰兩種工作狀一況。
  8. Given the rotational speed of the driving wheel, the temperature in the contact zero rises evidently as the load is increased. given the load, however, this temperature rises faintly as the rotational speed of the driving wheel increases. when the modulus is small and rational rate is high, the change of the rational speed and load have the apparent influence on the temperature distribution, but when the modulus is larger and rational rate no larger than 1. 0, the above changes have negligible influence on the temperature distributions

    當主動輪轉速一定時，隨著載荷的增加，接觸區的溫升明顯增加;當載荷一定時，隨著主動輪轉速的增加，接觸區的溫升卻無明顯變化;當模數較小、傳動比較大時，轉速和載荷的變化對接觸區溫度分佈的影響比較明顯;但當模數較大而傳動比i 『 1時，轉速和載荷的變化對溫度分佈影響較小。
  9. We then discuss the vibrational - rotational level transitions and the population rate equations for the laser. in addition, electron temperature, electron density and the mixtured gas temperature in the laser plasma are investigated in details. the third part is with regard to the optimal designs and the experiments of the lasers

    在二氧化碳激光動力學機理的研究中，比較詳細地討論了二氧化碳激光動力學過程，給出了激光振動-轉動能級躍遷及其速率方程、激光等離子體電子密度和電子溫度，以及混合氣體的氣體溫度
  10. Applying the computer program developed by this paper, and choosing the real values of the gear transmission, this paper has completed more than 50 sets of calculations of the thermal elastohydrodynamic lubrication based on the non - newtonian fluid. the following conclusions can be drawn according to the computational results : 1, when the gear teeth are engaged at the pitch point, the changes of both the gear rotational speed and the load have little influence on the pressure distribution and the film shape, but they have large influence on the film temperature distribution

    應用本文研發的計算機程序，選用齒輪傳動的實際參數，先後進行了50餘組的基於非牛頓流體的熱彈流潤滑計算，所得的主要結論如下： 1 、當齒輪在節點嚙合時，齒輪轉速及載荷的變化對壓力分佈口太原理工大學碩士學位論文和油膜形狀的影響不大，但對溫度分佈有明顯的影響。
  11. The telemetry delays for each tool have been standardization as channel alphabetical letters. so the telemetry gauge and interface circuit of tools are designed in this paper. the temperature data of the new kind of telemetry tools has special format consisting of an 8 bit digital temperature wore over an 8 frame time period for its high frequency and the data of flowmeter is uplinked on two time dot to determine downhole or uphole rotational direction

    本文重新設計了新型遙傳短節和參數測量儀器的介面電路，部分參數的介面電路完全採用硬體電路實現；針對溫度參數的數據頻率高於新型遙傳方式可傳輸頻率范圍的矛盾，提出了按「位」傳輸的新方式；基於流量參數特有的方向性，對流量數據採用了兩道傳輸的方式。
分享友人
分享到 Line

分享到臉書