sealing piston 中文意思是什麼

sealing piston 解釋
封嚴板
  • sealing : n. 獵海豹業。
  • piston : n. 1. 【機械工程】活塞。2. 【音樂】（管樂器的）直升式活塞。
  1. One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,

    溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。
  2. In the event that a boiler does shut down the stop - check must prevent backflow into the boiler, the weight of the disc and dash pot piston, through the force of gravity, promote rapid sealing so steam and condensate cannot backflow into the boiler even at low pressures

    如果鍋爐沒有關閉截止止回閥，則必須防止迴流到鍋爐上，閥瓣壓鐵和緩沖活塞，在重力的作用下，能夠迅速實現密封，使得蒸汽和冷凝水即使在低壓下也不會迴流到鍋爐里。
  3. Sealing components for reciprocating compressors. manufacturing and reconditioning. valves, piston rings, packing cases, rods, pistons

    -製造z zw型l lw型v vw型及車裝移動式四大系列壓縮機。
  4. The derivation of the leakage flow rate formula of the special annular clearance between the piston and cylinder under condition of variable viscosity in the axial piston pumps was carried out. at same time, considering the questions of the eccentricity and the variable sealing length of piston friction pair, the modified coefficient of the calculation formula of the flow - rate of the leakage was given

    在變粘度、柱塞偏心以及變密封長度條件下，對軸向柱塞泵中柱塞與缸孔之間的特殊圓環縫隙的泄漏流量公式進行推導，得到了該計算公式的修正系數； 6
  5. Through contrasting analyses of hydraulic cylinder structure and sealing condition, piston rod oil leak reason, inside leaking condition between piston and cylinder, with overseas cylinder structure and sealing dependability, the structure standardized between the piston and cylinder, piston rod and guide tube in unity was realized and obtained

    摘要通過對油缸結構、油缸密封使用情況、活塞桿處的漏油原因、活塞與缸筒間的內泄情況以及與國外油缸結構、密封可靠性相比較分析，實現活塞與缸筒，活塞桿與導向套之間密封的結構統一。
  6. The output axis and the piston have chosen high quality bearing which have good stability and sealing, low friction coefficient, large range of applicable temperature and long service lift

    輸出軸，活塞選擇了高質量的軸承，穩定性好，密封性好，摩擦系數低，適用溫度范圍大，使用壽命長。
  7. This task will be foundation to develop a new type hydrostatic transmission piston pumps with high efficiency, long life, high pressure and high speed, which combined the item of nature science fund of zhejiang province, tribology study on sealing, hydrostatic support and piston on hydrostatic transmission piston pump. in this paper, a new design idea of the ball friction coupling based on hydrostatic bearing was given, and analysis was carried out to the static state properties and the dynamic properties of the oil - film of this friction pair

    本課題是結合浙江省自然科學基金項目「靜壓傳動柱塞泵的密封、靜壓支承和柱塞的摩擦學研究」 （ 501073 ） ，為研發高效率、長壽命、高速、高壓靜壓傳動柱塞泵提供一定的理論基礎，著重研究了滑靴副和球鉸副的動靜態特性，提出了基於靜壓支承的球鉸副設計原理。
  8. Reciprocating piston compressor metal rectangle packing. part5 : tensile spring for sealing and wiper rings

    往復活塞壓縮機.金屬平面填料.第5部分:密封圈和刮油圈用拉伸彈簧
  9. Reciprocating piston compressor metal rectangle packing. part6 : technical specification for sealing and wiper rings

    往復活塞壓縮機.金屬平面填料.第6部分:密封圈和刮油圈技術條件
  10. Progress on the sealing of piston rods in hydraulic cylinders of construction machinery

    工程機械液壓缸活塞桿密封的進展
  11. Reciprocating piston compressor metal rectangle packing. part1 : three - inclined cut sealing rings

    往復活塞壓縮機.金屬平面填料.第1部分:三斜口密封圈
  12. Leakage on sealing surface, replaces the sealing piece. if the protrusion of the piston rod leaks oil, replaces the shaft ' s sealing piece

    密封面滲漏，更換密封件。如活塞桿伸出處漏油，更換軸用密封件。
  13. Disc holder ( 21 ) will drop out. carefully remove balance piston ( 18 ) so as not to damage sealing ring ( 16 ) as it is pulled through seat ring ( 19 )

    閥瓣支架（ 21 ）將會脫落。小心拆卸平衡活塞（ 18 ） ，在將平衡活塞通過密封環（ 19 ）拔出時，避免損壞密封環（ 16 ） 。
分享友人
分享到 Line

分享到臉書