second evaporator 中文意思是什麼

second evaporator 解釋
第二效蒸發器
  • second : adj 1 第二的；第二次的；二等（的）。2 次等的；較差的；劣於…的 （to）。3 〈美國〉較年輕的。4 另一...
  • evaporator : n. 蒸發器。
  1. Hot vapor from this unit passes to the second-effect calandria and causes boiling in the second evaporator.

    從這臺設備中出來的熱蒸汽通進二效的列管換熱器，使第二臺蒸發器中的液體沸騰。
  2. Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping

    本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。
  3. Second, the model for evaporator is founded based on traditional theory, including refrigerant side and air side, and the method for choosing element ; the calculation for the load of refrigeratory ; the thickness choice for heat insulation material ; the work area of evaporator is conformed ; and the matching for the other elements

    2 ）根據傳統理論建立了蒸發器的數學模型，包括冷劑側和空氣側的數學模型、微元的選取；冷庫冷負荷的計算和確定；隔熱材料合理厚度的選擇；蒸發器工作面積的確定；以及其他製冷元件的匹配理論。
分享友人
分享到 Line

分享到臉書