selected material 中文意思是什麼
selected material
解釋
用料上乘-
This company strictly according to the iso9001 - 2000 management system request, utilizes the advanced bamboo processing complete set of equipments, uses the advanced domestic and foreign productions craft, the raw material is selected from the high quality natural bamboo, through steamed and boiled in the high temperature, got rid of the sugar and the degrease, carbonized, past the high temperature and thermo - compression
廠區一角本公司嚴格按照iso9001 - 2000管理體系要求，運用先進的竹加工成套設備，採用國內外先進生產工藝，選用優質天然楠竹為原料，經過高溫蒸煮脫糖脫脂碳化高溫熱壓等數十道工藝，生產防霉防蛀阻燃的「湘君」牌綠色環保型系列產品。 -
Above all, alloy ductile cast iron is generally selected as the material of edger roll and its durability is better than high carbon semi - steel
綜上所述，國外型鋼軋邊輥材質一般選用合金球墨鑄鐵軋輥，所以其耐磨性也相應地優于高碳半鋼。 -
" the martin iraq ascended " publishes in 1909, the first half had discusses himself, selected material myself before the experience and afterwards becomes famous the process in the jake london, the main plot then was fictionalizes
《馬丁?伊登》發表於1909年，前半部帶有自傳性，取材於傑克?倫敦本人早年的經歷和后來的成名過程，主要故事情節則是虛構的。 -
Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously
應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。 -
And production fashion is selected optional for assurance of the material character of hpch. the hpch material, in which the compound technique route of polybasic components is applied, has better properties such as high workability, high durability, low ion transference rate and so on
採用多組份復合技術路線配製出高工作性、高耐久性、低離子遷移率的hpch材料，對其宏觀物理力學性能、耐久性能和微觀結構進行了分析研究。 -
It measures the density of oxygen by detecting the life - span of the fluorescence quenching. the so - called fluorescence quenching is a kind of physics or chemistry process that the fluorescence material has chemical or physical reactions with certain substance is selected here. it has the advantage of good stability of fluorescence, long life span and the strong quenching effect
本課題光纖氧氣傳感器檢測系統是基於熒光猝滅效應的檢測機制，通過測定熒光壽命從而檢測氧氣濃度的，熒光猝滅效應所引起的熒光壽命具有很好的穩定性、猝滅效果以及系統使用壽命長。 -
In production practice, ramie and cotton were blended and selected as the raw material to produce the slub yam with the performances of its spinning process also analyzed and summarized
結合生產實踐，選擇了苎麻棉混紡竹節紗的原料和混和方式，分析總結了紡紗工藝特徵。 -
As the double - sided term implies, the tapes use selected adhesives to coat both sides of backing material, they are then pressed on to release paper for separation purposes. double - sided tapes are intended to replace glue for bonding and fixing purposes
雙面膠粘帶是在基材的兩面塗上壓敏膠，再覆以易剝離的離型材料製造而成，廣泛用於兩物體的和固定，使用十分方便。 -
Refractory fiber and product is manufactured by means of dry method and wet method. as an excellent insulation material, it has comparatively low volume density, good softness and very low thermal conductivity coefficient. sticking method, ancjoring method and folding method can be selected respectively. this product can be used in various industrial kilns & furmaces for lowering heat consumption
耐火纖維及製品是採用干法、濕法生產的具有較低體積密度、較好柔軟性、極低的導熱系數的優質絕熱保溫材料，施工時可分別採用粘貼法、錨固法、折疊塊形式施工，適用於各種工業窯爐降低熱耗之用。 -
Because of insistence in our research, management. competitive price, good quality, selected material exquisitely and strict test, plus the excellent service for the clients, leads to our success in the severe competition
持久不懈的研究，全面的質量管理，精細地選用材料和嚴格的檢測手段，使本公司產品質優價廉，加之對客戶良好的服務態度，這就是我們在激烈的競爭中取得成功的要素。 -
The experimental results show that the characters of tree height, dbh, and volume, etc. of every family progenies of pinus massoniana seed orchard are all evidently higher than those of control ( ck ), 7 fine family materials whose volume growth exceeds the control ' s by 50 % are totally selected as the materials for building p. massoniana improved seed orchard and industrial raw material forest
摘要對漳平五一國有林場馬尾松種子園18個初選家系進行子代測定，採用隨機區組設計、 8次重復，對6年生的樹高、胸徑、材積等性狀進行測定，試驗結果表明：馬尾松種子園各家系子代均明顯高於對照（ ck ） ，共選出7個優良家系材積生長超過對照50 %以上材料，作為營建馬尾松改良種子園和工業原料林的材料。 -
Besides, scan rate and cycle period also affect the result ; co - deposition of dualistic oxide is a focus of research, as an element in the same group, ir is selected. deposition rate of composition is decreased by the adding of ir composition, and when the proportion of ir exceeded 50 %, composition procession can be ceased. but cooperation of ir and ru oxide can highly increase the specific capacitance of active material ; annealing treatment under a certain temperature can help to change the hydrate ru composition into mixture state ru oxide, accordingly increase the stabilization of active material
研究表明:電解液的配製過程中，氯化釕濃度、溶液ph值、陳化時間、溶液溫度對電鍍效果均有影響，其中溶液ph值是最主要的影響因素;在儀器的使用條件探索中，理論結合實驗確定了本電鍍液體系循環伏安電勢窗的理想范圍，並發現循環伏安掃描速度和掃描周期對電鍍結果也有較大影響;混合氧化物的共沉澱是目前研究熱點，在此選用與釕同一族的銥作為共沉澱元素，銥的加入會阻礙氧化物的沉積速度，銥的比例超過50 %會使沉積作用停止，但是二元氧化物的協同作用使沉積的活性物質比容量大大提高;一定溫度下退火后處理作用會使水合釕化物轉變成混合價態的氧化釕，從而提高活性物質的穩定性。 -
The research work in this paper was carried out at the second power factory of xici subsidiary. the production technology of strontium ferrite was studied and wet process of strontium ferrite pre - sintering material with anisotropic characteristic was determined. products of y30h - 2 which meet the standard series of sj / t10410 - 1993 were selected to be experimental products
本文以西磁分公司料粉二廠為基點，研究了鍶永磁鐵氧體生產的工藝技術路線，確定了濕法工藝生產各向異性鍶永磁鐵氧體預燒料，並將試驗產品定位在sj t10410 - 1993標準中的y30h - 2產品。 -
In this article, the steel fibre is a kind of industrial wastes - stainless steel fibre dregs. the use of it is helpful in comprehensive utilization of resource and environment protection. the author of this article used orthogonal test design, arranged the test scheme scientifically, selected material, at last yield a high strength concret, whose strength exceeded c60, mainly by using 42. 5 ordinary portland cement, silica fume, superplasticizers, stainless steel fibre dregs and so on
本文所用的鋼釬維是一種工業廢料?不銹鋼纖維渣，它的應用有利於資源的綜合利用和生態環境的保護本文在廣泛閱讀國內外有關資料的基礎上，採用正交設計，科學地安排試驗方案，精心選擇材料，用42 . 5普通硅酸鹽水泥、硅灰、高效減水劑、不銹鋼纖維渣等材料，採用常規工藝配製出了強度達到c60的高強混凝土，並且通過對試驗數據的分析，給出了最優配比方案。 -
The material of electro - fused magnesia sinter is selected from special grade a natural magnesite or high - purity caustic calcined magnesite, which is fused in arc furnace to finish the products. the products possess high purity, crystal with and compact texture, have high heat - vibration steady and cinder corrosion resistant, it is used for making high quality magnesite bricks, magnesia - carbon bricks
電熔鎂砂是用精選的特a級天然菱鎂石，在電弧爐中熔融制得，該產品具有純度高，結晶緻密，抗渣性強熱震穩定性好，是製作高檔鎂磚，鎂碳磚及不定形耐火材料的重要原料。 -
The author of this article used orthogonal test design, arranged the test scheme scientifically, selected material carefully, at last yielded an ultrahigh strength cement - based material ( uhscm ), whose compressive strength exceeded 100 mpa, mainly by using 42. 5 ordinary portland cement, superfine aggregate : nano sio2, superplasticizers and so on
本文是在廣泛閱讀國內外有關資料的基礎上，採用正交設計，科學地安排試驗，精心選材，用42 . 5普通硅酸鹽水泥、納米sio _ 2 、高效減水劑等材料，採用常規工藝配製出了一種抗壓強度超過100mpa的高強水泥基復合材料。 -
The author of this article used orthogonal test design, arranged the test scheme scientifically, selected material aboratively, at last yield a ultrahigh strength cement - based material ( uhscm ), whose compressive strength exceeded 120 mpa, mainly by using 625r ordinary portland cement, superfine aggregate - - silica fume, superplasticizers and so on
本文在廣泛閱讀國內外有關資料的基礎上，採用正交設計，科學地安排試驗方案，精心選材，用625r普通硅酸鹽水泥、超細顆粒集料硅灰、高效減水劑等材料，採用常規工藝配製出了一種抗壓強度超過120mpa的超高強水泥基材料。 -
The preferences are analyzed, pipe ’ s parameters such as depth, thickness, pipe diameter, and mechanical property of material ; soil parameters such as soil types, internal friction angle, pipe - soil interaction ; fault ’ s parameters such as fault types, fault throw, fault drop, fault - pipe angle, mechanical property of material ; load types such as gravity force, linear displacement load, seismic load and seismic wave. some conclusions are drawn from the calculating results : when buried pipes cross fault, pipe ’ s embedded depth should be shallow, and big pipe diameter and thick wall should be selected. avoid the site where fault moves severe, and select suitable pipe - fault angle
在有限元三維模型建立中考慮的因素有:管道自身參數如管道埋置深度、管壁厚度、管徑、管道材料等;巖土材料參數如土體類型、巖土的內摩擦角、管土相互作用等;斷層考慮有斷層類型，斷層斷距，斷層錯動距離，斷層與管道的交角，斷層材料的考慮等;荷載分別考慮靜荷載，動荷載，其中動荷載包括線性位移加載、地震力加載和地震波加載等。 -
The author of this article used orthogonal test design, arranged the test scheme scientifically, selected material carefully, at last yielded an high strength lightweight aggregate concrete material ( hslacm ), whose compressive strength exceeded 50 mpa and quality under 1950kg / m3, mainly by using 42. 5 ordinary portland cement, expanded fly ash aggregate, silica fume, superplasticizers and so on
本文是在廣泛閱讀國內外有關資料的基礎上，採用正交設計，科學地安排試驗，精心選材，用42 . 5普通硅酸鹽水泥、粉煤灰陶粒、硅灰、高效減水劑等材料，採用一般工藝配製出了一種抗壓強度超過50mpa 、質量低於1950kg m ~ 3的高強輕骨料混凝土材料。 -
A reasonable method is carried out for the design of the ego in the present work. it is : ( 1 ) optimizing the selected material and structure of the ego
本論文實施了一種科學的車用氧傳感器開發研製的可行方法，即門）運用科學的設計思路對氧傳感器的選材、結構實行了優化。
分享友人