serial data transfer 中文意思是什麼
serial data transfer
解釋
串列數據傳輸-
Ieee 1394 is a high - speed serial bus standard which supports data speed up to 400mbps, hot - pluggable and has two types of data transfer : asynchronous and isochronous. all these characters make it be considered the first choice of near - term on - board spacecraft architectures for data transfer
而ieee1394高速串列總線具有支持400mbps的等時和異步傳輸，可熱插拔，使用方便靈活等特性，使其成為未來星載高速總線的首選。 -
1. usb1. 1 interface, faster than serial port data transfer, no extra power supply required
1 . usb1 . 1介面，比serial port串接埠傳輸更快，不需外接電源 -
The bulk data transfer module is based on usb ( universal serial bus ) technology. its speed is much faster than that of serial port, and devices based on usb tie up much fewer hardware i / o address resources than pci devices do
數據傳輸介面基於usb （ universalserialbus ）總線技術開發，具有即插即用功能及較快的數據傳輸能力，這相對于過去使用的標定設備具有很大的技術先進性。 -
During the design of vxi - bus serial controller module, the functions of vxi - bus including time - sequence for vxi interface, resource management, interrupt process, bus arbitration, are accomplished. to advance the performance and stability, the fpga technic is used to implement the kerneled code including serial bus time - sequence switching to vxi interface time - sequence, the uart, the parameterized baud generator and “ pipeling frame ”. the handle type of data transfer bus for vxi - bus is researched thoroughly, and the format of serial data transfer is designed
在vxi總線串列控制器設計中，實現了vxi總線控制器的基本功能，包括vxi總線介面時序、總線仲裁、超時處理等;同時利用先進的fpga技術實現了串列總線時序向vxi總線時序的轉換、通用異步收發器（ uart ） 、參數化波特率發生器、流水線結構等功能模塊;在設計中還深入研究了vxi總線數據傳輸的各種操作類型，制定了串列數據傳輸的編碼格式。 -
Tagged command queuing : data transfer optimization in wd raptor el74 serial ata hard drives
標記指示隊列tcq ： wd raptor el74序列ata硬碟機的進階資料傳遞功能 -
There are six sub - modules in it : single - chip unit, data transfer unit, parallel data transfer / receive unit, serial data transfer / receive unit, system reset management and system power unit. this paper studies the design and realization of net interface module, mainly discusses design of data transfer unit ' s logic and the improvement of single - chip unit ' s software
論文首先從系統設計思想出發，對網路介面模塊的總體設計實現進行了研究，接著對作者主要研究的軟硬體分工協同設計中的軟體完善部分，邏輯設計部分，以及最後的邏輯測試、系統測試進行了重點論述。 -
The system abandons the serial communication that is low speed and low effect, but change to use the printing port, realizes the high speed, efficient parallel communication, further more choose to use to the ecp ( extended capabilities port, ) mode of parallel communication. according to the outside physical transfer ability, this mode can automatic adjust the transfer speed, and realize the data communication with the arbitrary speed
該系統在上下位機的數據傳輸中，摒棄了低速、低效的串列通訊，而改用列印口，實現了高速、高效的并行通訊，並且選用了並口的ecp （ extendedcapabilitiesport ，擴展功能介面）模式，可以根據外設的實際傳輸能力自動調整傳輸速度，實現任意速度的數據通訊。 -
In this system, there are many method of data transfer ( including : modem, serial port, w / r 1c card, infrared transmitting, gsm transmitting and embedded internet ), so the dependability is better than before
此系統中的數據傳輸（包括modem 、串口傳輸和ic卡讀寫，也論及紅外傳輸、 gsm傳輸及嵌入internet式） ，方式多樣化，可靠性比目前的系統要好。 -
Fieldbus is a kind of digital, bi - directional serial data transfer and multi - branch communication network which connects intelligent equipment and automatic system. can bus is used in communication between plc and can modules in this system
現場總線是連接智能現場設備和自動化系統的數字式、雙向串列、多分支結構的遠程通信網路，本系統將使用甚廣的can總線技術應用於plc以實現與輸入輸出模塊的通訊。
分享友人