shear member 中文意思是什麼
shear member
解釋
抗剪構件-
Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。 -
6. the sectional cross - sectional discrete yield - sruface model is used to spandrel deep beams, the effect of the shear deformation to shear force on ( he m ~ terial nonlinearity is considered, ( he bond slip in anchorage zones is regarded as the houndaty nonlinearity of a member. except the geometric nonhineaicty. consideration of double nonlinearities about materials an
6 、將分段截面離散的屈服面模型法應用於裙梁，考慮剪力剪切變形對材料非線性的影響，將錨固區鋼筋的粘結滑移看成構件的邊界非線性，不考慮幾何非線件，建立了裙梁考慮村料、邊界雙重非線性的空間滯回曲線分析模型。 -
To enhance floor rigidity, not means to increase floor thickness. with all the building shape and location of anti - shear member known, shear error can not be limited within 8 % compared floor rigid assumption to elastic assumption
在建築體形及抗側力構件的布置均已確定的前提下，單純靠增大樓板的厚度並不能把按剛彈性計算的剪力誤差值控制在8以內。 -
The possible shear of the upper chord will change beam from flexural member to member under flexure and compression force. this is emphasised through design example. as a result ， we find that composite floor system is good for reducing the height of floor system
在組合樓蓋體系設計中，筆者指出，可能的桁架弦桿剪力會使作為桁架弦桿側向支承的梁由彎曲構件變為壓彎構件，這是在與桁架體系相適應的樓蓋體系設計中應該注意的一個環節。 -
The lower member of typical ophiolite suit is exposed at outsides of the qimanyuter ophiolite melange and in between, there distribute the basalt, deep sea limestone and silicalites. these different litho - members contact to each other with ductile shear zones
帶內蛇綠巖套下部單元出露于兩側，玄武巖和相關的深水灰巖、硅質巖等分佈於中部，各單元間均以韌性剪切帶接觸。 -
Firstly, the shear and normal stresses of tapered members under the transverse load or axial load are analysed, and the stresses formulas are obtained which are different from those of the prismatic ones. secondly, research is done on the in - plane inelastic stability of tapered members under axial loads about strong axis and weak axis. a new design method is suggested in which the tapered member is equivalent to the prismatic member with the cross - section at the larger end of the tapered member
同時由分析可知，目前採用的將變截面壓桿按照彈性極限荷載等效的原則等效成以小端截面為準的等截面壓桿的設計方法，在彈塑性階段低估了壓桿的承載力，即彈性等效的壓桿在彈塑性階段並不等效，實際變截面壓桿的承載力比等效的等截面壓桿的承載力要高。 -
Then calculate the member individually, including the calculation of load - behavior capacity, the calculation of high strong bolt with the method of connection with beam, the design method of stiffening rib, etc. the text educed the above - mentioned formula theoretically. 5. linking with windmill flat engineering example in the third youth flat engineering of yi zhuang development area, beijing, it and steel frame constitute the steel frame ? steel shear wall with slit system respectively are analyzed the whole structure by ansys and satwe
既利用剛度等效的原則，把其轉換為工程計算軟體可以計算的支撐體系，然後對構件進行單獨計算，包括承載力的計算、和梁接合方法? ?高強螺栓的計算、加強肋的設計方法等內容； 5 、帶縫鋼板剪力墻與鋼框架形成鋼框架? ?帶縫鋼板剪力墻結構體系，結合北京亦莊經濟開發區青年公寓三期工程中的風車公寓工程實例，分別採用ansys和satwe進行了結構整體分析，兩者的計算結果相吻合。 -
Although two simple models of structural analysis models, namely multi - storey shear type and member model, are set up, it is proved that simulink show great dominance in simulation of structural dynamic response, especially in vibration control
本文所做的工作雖然僅實現了結構分析模型中較簡單層間模型和平面桿系單分量模型的非線性地震反應模擬，但已足以體現出simulink用於結構動力模擬和結構振動控制的優越性。 -
This paper introduce simulink to simulation of structural nonlinear seismic responses innovative, working on regulation and dominance of simulation of structural dynamic response of simulink based on muti - storey shear - type model and member model, and set up basic block of structural dynamic response to pave the way for wide analysis of structural dynamic response, especially vibration control
本文開創性地將simulink引入結構非線性地震反應模擬中，以層間剪切模型和平面桿系模型為對象，努力探討simulink用於結構動力模擬的規律並發掘其優勢，編制結構動力模擬的基礎性模塊，為逐步實現更廣泛的結構動力分析尤其是結構的振動控制奠定基礎。 -
Member shear beam member shear beam
構件梁剪切梁 -
Member shear beam load shear beam
構件剪切梁 -
Basing on the feature of the structure member, the structure is simplified to a 3 - d model consist of space beams and shells, so we can make response spectrum dynamic analysis on the finite - element models. at last nonlinear finite element dynamic analysis was made about the structures. the calculated results reveal the rule of dynamic response about model the and show that the aseismic behaviour and failure mechanism of shear wall structure with src supporting frames and src girder transfer floor is better than that of rc one
在7度多遇和罕遇地震力作用下，通過對振型、側向位移、傾覆力矩和剪力在給定抗側力結構間分配的比較，以及對框支柱和剪力墻的地震響應、轉換層樓板應力比較等模擬分析，得到型鋼混凝土梁式轉換層框支剪力墻結構較鋼筋混凝土梁式轉換層框支剪力墻結構抗地震力特性上有較明顯的改善的結論。 -
Floor rigidity has relations not only to floor stiffness, but also to stiffness and location of anti - shear member. neither floor length to width ratio nor stiffness ratio of floor to shear wall should be the guild line of rigid floor
不能單純地根據樓板的長寬比的范圍來確定樓板是否為剛性樓板，也不能簡單地根據樓板與剪力墻的剛度比來判斷樓板是否為剛性樓板。 -
Based on the comprehension of simulink, this paper build multi - storey shear - type models and member models based on bi - linear type and takeda type after many blocks of simulink were set up
通過兩個算例分別對上述兩種分析模型進行了計算結果分析，並與通用軟體進行了對比，計算結果具有較好的穩定性和可靠性。 -
With the development of high - rise building, the normal strength concrete and high - strength concrete are applied more and more extensively. it is necessary to study much more behaviors of combined - force member under gone bend, axial press, shear and torsion
普通混凝土及高強混凝土隨著高層建築的發展得到廣泛的應用，有必要對普通混凝土和高強混凝土承受彎壓剪扭復合受力構件的結構性能做進一步研究。 -
Aimed at the steel shear wall with slit, a systematic research is done on the forced performance. by using the finite element soft ware ansys, the paper analyzes this lateral resistant member. the main part of the text has three aspects : the calculation of the lateral stiffness, the analysis of nonlinear material and simulation of hysteretic loop
結果表明，帶縫鋼板剪力墻是一種優良的抗側力構件，有著其它抗側力構件無法比擬的優點； 2 、針對帶縫鋼板剪力墻，本文對其受力性能進行了系統研究，並用有限元軟體ansys進行了分析。 -
The project is completed in the collaboration of the transportation college of jilin university and transportation science institute in jilin province. the paper mainly studies the characteristics and mechanical performance of small size member of bridge, the problems of concrete dense degree and shear lag effect of wide flange. the static load test and supersonic nondestructive test of four pieces of prestressed i - girder with varying section are carried out in bridge structure laboratory of jilin university
本文針對橋梁構件局部尺寸較小部位的混凝土密實度問題，進行了2片腹板寬度為14cm ， 2片腹板寬度為16cm的變截面預應力工字梁的靜載試驗和超聲無損檢測試驗，提出密實度系數的概念，對試驗梁的密實度進行定量評定，推導了工字梁的塑性系數公式，基於塑性理論給出了試驗梁的開裂荷載和極限承載能力計算公式，分析了試驗梁的密實度對其開裂荷載和極限承載能力的影響。 -
2. for frame supported double - short - pier shear wall under vertical loads, the non - noding area of transfer beams turns into a member of flexure and tension with small axial force, and bending stress dominates in the stress distribution on the cross - section. in the nodding area, the axial force increases while the bending effect is small
2 、框支雙肢短肢剪力墻在豎向荷載作用下，轉換梁的非節點區為一拉彎構件，軸向拉力較小，截面的應力分佈以彎曲應力為主;在節點區，軸向拉力效應增大，而彎曲效應很小。
分享友人