shearing plane 中文意思是什麼
shearing plane
解釋
剪斷面-
Based on the continuous damage theory, considering the shear effect, the high - order shearing, flexural and in - plane deformation coupling model is built ; through the nonlinear fem analysis of rc beams strengthened with frp, the damage theory and damage course is researched ; compared with experiment results, it shows that the model is effective ; the fem analysis software is prepared to provide simple and effective method for the engineering application ; using the soft the frp strengthened beams before and after damage is modeled so as to provide the theory base for engineering application
摘要基於連續損傷理論，考慮膠層的剪切效應，建立frp加固鋼筋混凝土梁的高階剪切彎曲及面內變形耦合模型，編制了有限元分析的軟體，進行非線性有限元分析；通過與已有的試驗結果進行對比，證明該模型的簡單，有效性；利用該軟體對未加固混凝土梁，初始進行加固的混凝土梁以及最大拉應變達到極限值時進行加固的混凝土梁等幾種情況進行數值模擬。 -
But because there are shearing stress and removing stress on the gluing plane between the steel plates and concrete, the phenomenon of premature removing of the steel plates in the strengthen beams is easy to take place
但是，由於鋼板和混凝土粘結面上存在粘結剪應力和剝離拉應力，使粘鋼加固梁容易發生鋼板端部和彎剪區段跨中的早期剝離破壞現象。 -
The demarcation point of, which is the parameter in erf ' s yield stress equation, is 2. 0. for, the dynamic characteristics of the clutch are remarkably different from those for. thirdly, the linear stability of plane shearing flow with non zero pressure gradient is studied
論文第三部分對電流變液非零壓力梯度平板剪切流動的穩定性進行了分析，提出流場對屈服應力達到飽和的概念；並得出平板壁面剪切運動以及電流變液屈服應力的提高，都將使流動穩定性增強的結論。 -
- 2. in order to accomplish the extraction measuremellt of distorted wavefront on specific plane of a laser beam, a crsi ( cyc1ic radial shearing interferometer ) based on relay imaging technique was built. the experiinental result on this crsi shows it can used to test the spatial mid and low frequency wavefront distortion
二、為了實現激光光束在確定平面上的波前畸變的準確檢測，採用中繼成像技術建立了一套基於空間相位調制的環路徑向剪切干涉波前傳感硬體系統，實驗證明，它可用於中低頻段波前畸變的檢測。 -
At here, based upon designing idea of the shearing planes of left and right two shears are at 45 with respect to main transmission plane and the combination with changeable structure, the shearing mechanism of two mutually twisted flat screw wires was designed
在此，基於左右兩把剪刀的剪切平面相對于主傳動平面成45 ，以及與變結構相結合的設計理念，設計出了兩根互繞扁螺旋鋼絲的剪切機構。 -
The conception of yield stress saturation is proposed. it can be found that the flow is stabilized by both plane shearing and the increment of yield stress. the study about the linear stability of spiral taylor - couette flow is the fourth part of the dissertation
通過對螺旋t - v流動的數值模擬發現，屈服應力增大將使流場中taylor渦減弱，且當屈服應力足夠大時，螺旋t - v流動重新恢復螺旋t - c流動；內桶軸向剪切運動在使taylor渦發生軸向遷移的同時也使其強度減弱。 -
The second part of this dissertation is the dns study of a two - dimensional gas - solid two - phase strong - shearing plane turbulent jet
本文的第二部分為二維氣固兩相強剪切平面湍流射流的dns研究。 -
Secondly, the push - over analysis is for the three - dimensional solid element model and the plane beam element model. the total shearing force - lateral displacement curve can be obtained from it. and then the total shearing force - lateral displacement curve is converted to pseudo acceleration - period curve and some comparisons are made between the pseudo acceleration - period curve and design response spectrum
然後，建立了有限元三維實體單元模型及平面桿單元模型，對其進行了push - over分析，並將所得的底部剪力一頂點位移曲線轉化為擬加速度一周期曲線，與規范反應譜進行對比，以此評定該體系的抗震能力。
分享友人