shell model calculation 中文意思是什麼

shell model calculation 解釋
殼模型計算
  • shell : n （pl shells 2 義為 shell）1 殼；介殼；甲殼；貝。2 （昆蟲的）翅鞘；蛹的蛻皮。3 【解剖學】種子的...
  • model : n 1 模型，雛型；原型；設計圖；模範；（畫家、雕刻家的）模特兒；樣板。2 典型，模範。3 （女服裝店僱...
  • calculation : n. 1. 計算，計演算法。2. 推定，預測。3. 深思熟慮，精打細算；慎重的計劃；算計。
  1. For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels

    為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。
  2. In this paper, micro - cavity semiconductor laser ( mcsl ) with pillar vertical - cavity surface - emitting structure ( vcsel ) which has potential applications in optical communication and optical interconnect is theoretically analyzed, the calculation model that used to discuss the modal performance of rectangular columnar and cylinder vcsel with oxidized aperture is established by using vector field model. the numerical simulations in the case of cylinder structure show oscillating wavelength and threshold gain against inside and outside radius of laser, the layer refractive index and pair number of bragg mirror, thickness, position and oxidized material ' s refractive index of oxidized aperture, in detail. more practically, considering dos shell of laser as non - perfect one, or supposing that dos shell is separated from the laser, we can obtain more significative results

    本工作以矢量場模型出發，對具有誘人應用前景的柱形垂直腔面發射結構（ vcsel ）的微腔半導體激光器（ mcsl ）進行了理論分析，建立了用於分析方柱形和圓柱形結構具有氧化孔徑層的激光器的模式特性的理論模型；對圓柱形結構情況進行了數值模擬，得到了振蕩波長、閾值增益隨激光器內外半徑、 bragg反射鏡層折射率、周期數以及氧化孔徑層厚度、位置和氧化物折射率的詳細變化規律；為使理論計算更接近實際，將外加金屬包殼視為非理想導體，或將金屬包殼與激光器結構隔開，分別對這兩種情況下的結果進行了討論。
  3. The research object in this text is the actual project - - the mansion of yatingyuan ( 40 layers above the ground, 125. 4 meter high ). the structure - design is by satwe and the analysis of the structure dynamic characteristic and earthquake response by sap2000, whose calculation models are set up according to the actual size of the structure. in satwe, the analysis model of beam and column is simulated by frame - element, slab is plane - element, shear - wall is wall - element and slab is infinitely rigid in the internal and zero in the external ; in sap2000, beam and column is frame - element, slab and shear - wall is shell - element and slab is elastic floor

    本文以實際工程項目? ?雅庭園商業中心大廈（地面以上40層，建築總高度為125 . 4米）為研究對象，結構設計採用satwe ，結構的動力特性和地震反應分析採用sap2000 。結構satwe和sap2000分析的計算模型均按結構的實際尺寸建立， satwe分析模型的樑柱採用桿元模擬，樓板用薄壁殼元模擬和剪力墻用墻元模擬，樓板平面內無限剛、平面外剛度為零； sap2000分析模型的樑柱採用桿元模擬，樓板和剪力墻用殼元模擬，樓板為彈性板。
  4. The main studies of this thesis have been focused on the mass transport phenomenon in the hollow fiber membrane contactor, including the development of the model of the gas diffusion through the microporous membrane, the analytical solution of the shell side mass transfer differential equation in an orderly packed parallel flow module, the calculation of the shell side flow distribution in a randomly packed module, the estimation of the influence of the random arrangement of the fibers on the shell side mass transfer, and the experiments of the absorption of co2 into water

    膜接觸器是一種通過膜作為兩相之間的分離界面而實現相間傳質的雜化膜過程。本論文主要研究中空纖維膜接觸器的傳質行為，研究內容包括氣體通過微孔膜擴散模型的建立、中空纖維膜均勻分佈的平行流組件殼程傳質微分方程的解析求解、中空纖維膜不均勻分佈組件中流體分佈的數學計算、中空纖維膜不均勻分佈對殼程傳質影響的估算以及co _ 2氣體吸收實驗。
  5. The benchmark data for theoretical analysis are obtained by calculation results of finite element models. in order to have a sound finite element model, the plastic quadrilateral shell elements model established in 1996 by bahaari and sherbourne is improved by using solid 8 nodes elements in ansys programs

    為了使理論分析有充分而且精確的基本數據，本文改進了bahaari和sherbourne提出的四邊形塑性殼單元有限元模型，建立了能夠考慮焊縫、摩擦力和預應力等因素影響的端板連接節點的三維實體單元有限元模型。
  6. Then, three methods of diagonalization in quantum mechanics and calculation of shell model were discussed

    接著討論了量子力學中的對角化方法的分類和殼模型的計算。
分享友人
分享到 Line

分享到臉書