signal fault 中文意思是什麼
signal fault
解釋
信號故障-
This thesis studies the law of affecting de - noise result and the selection of the threshold and the wavelet function, the combination of wavelet and fft in the fault diagnosis of turbine - generator sets : by the de - noise anslysis of blocks and sin signals, concludes : to blocks signals, usually adopts soft threshold ; the law of affecting de - noise result is when use wavelet auto - de - noise, with the increasing of decomposed level, the de - noise result becomes worse while the level blow the 3, when the level above 3 and when uses wavelet packet, it is the other way round ; the best de - noise methods of the signal is that uses " dbl " wavelet function, three level, soft and " rigrsure " threshold
本文研究了分解層數對消噪結果影響的規律和閾值、小波函數的選取，結合小波分析與fft分析診斷汽輪發電機組的故障。通過對brocks和sin兩信號的分析，得出：對blocks信號進行分析一般採用軟閾值；分解層數對消噪結果影響的規律為用小波自動降噪在分解層數小於3時，隨著分解層數的增加，消噪結果變好，反之，則變差，用小波包降噪時隨著分解層數的增加，消噪效果變好；適宜選用dbl小波軟rigrsure閾值自動消噪。 -
The time - scale amplitude plot and phase plot based on hermitian wavelet transform are presented to singularity detection of signal. the corresponding relation relation between singularity and amplitude plot or phase plot is created. as successful application, fault of axletree damnify is found by means of this method
提出了基於hermitian小波變換的時間?尺度幅圖和相圖來識別信號奇異性的方法，建立了信號奇異點與幅圖和相圖的對應關系，在軸承損傷故障診斷中取得了成功的應用。 -
When forestage dcs system or pid regulator happened fault, manipulator receiving failure signal immediately switch into manual control state, by keystroke controls operation signal output
可分別帶有一路pid控制輸出及一路變送輸出。具有多種曲線控制輸出功能：可實現曲線控制暫停清零步進等。 -
In the first part of the paper, the development of motor control system fault diagnosis theory is summarized. on the basis of the analysis of the characteristics of wavelet, the theory is discussed and the definition of the singularity is given. because of the localization property of wavelet transform, wavelet analysis can be used to detect the characteristics of the singularity from the signal and intermittence fault problems lying in the motor under test
著重介紹了小波分析在電機控制系統故障診斷中的應用，根據小波理論在時域和頻域良好的局部化性質，討論了利用小波變換來檢測信號的奇異特徵的原理，給出了小波變換對信號奇異性特徵檢測的方法，針對實際應用，對小波基函數選取及小波分解尺度進行了探討。 -
The fractal theory application to fault diagnosis is tried in order to overcome the defec t of wavelet transform to nonlinear signal analysis and complicated machine diagnosis, including the concept, function and application about fractal dimension and the process of applying it to analyze the libration signal of rolling bearing and engine burning
針對小波變換分析復雜非線性機械繫統時表現出的力不從心，又嘗試探討了分形理論在故障診斷領域中的應用，討論了分形維數的概念、物理意義和應用，並通過滾動軸承和發動機燃燒振動信號的分析例示探討和展示了應用分形方法進行故障診斷的方法和過程。 -
Fast algorithms of both discrete and orthonormal wavelet and wavelet packet coefficient are diagrammatized to be introduced. daubechies wavelet is applied to help to discuss the application and test on signal filtering and noise reduction with the principle and threshold implementation ; the basic principle to pickup the fault characteristics is introduced mainly about the relations between the maximum module and signal saltation point and how to characterize the saltation point with lipschitz exponent
展示了離散正交小波變換的mallat快速演算法和小波包系數分解的快速演算法；重點應用daubeches小波探討了小波變換在信號濾波去噪中的應用和實驗，闡述了其基本原理和通過閾值化處理實現濾波的具體方法；探討了用小波變換進行故障特徵提取的原理，說明了小波變換模極大值和信號突變點之間的關系以及怎樣用李氏指數來表徵突變點的性質。 -
The 135 series of internal combustion engine unit are used as the major power devices for our national signal corps. once fault occurs, it will impair the communication between armies, resulting in potential grievous losses
=作為我國陸軍通信兵種主要動力設備的135系列內燃機組，一旦發生故障將嚴重影響我軍的通信聯絡，造成不可估量的重大損失。 -
Based on the theories described above, calculation formula of general dimension of least square measure and multi - fractal fault diagnosis and analysis system have been established with borland c + + builder 5. 0, and checked by pure sinusoidal and cosine signal and sinusoidal signal with noise, and verified by the examples
基於上述原理，建立了最小二乘法的廣義維數計算公式，用borlandc + + builder5 . 0編制了以廣義維數計算分析為基礎的多重分形故障診斷系統，並對標準的正弦信號、餘弦信號及帶有噪聲的正弦信號進行了驗證。 -
This dissertation is chiefly act below work : ( 1 ) expatiating the equipments diagnosis technique development process and trend, putting forward the standpoint that giving systematical diagnosis to the mechanical and electrical equipment and expanding the technical application in equipment diagnosis, making it breakthrough the traditional application of maintaining etc. in equipments, still be used for improvement and development etc. s of new product ' s design ; ( 2 ) probing into vibration type and disposal method of vibration signal, the usual method of equipment condition recognition, the essential constitutes and development trend of observation and diagnosis system ; ( 3 ) introducing the development trend of domestic and international crusher and the distinguishing feature of double turnplate stike crusher which is a new product. according to the breakdown phenomenon in running process, establishing the fault tree and deducing every kind of foundation affairs resulting in fault ; ( 4 ) studying the calculation method of critical rotation speed
本文主要做了以下工作： （ 1 ）闡述了設備診斷技術的發展過程及發展趨勢，提出了應結合實際對機電設備進行系統診斷的新的技術思路，用實踐證明了應當拓寬設備診斷技術應用的范圍，使設備診斷技術既可以在設備管理和設備維修中得到應用，也可以用於新產品的設計改進及開發等； （ 2 ）探討了振動的類型及振動信號的處理方法，設備狀態識別常用的方法，監測與診斷系統的基本構成與發展趨勢； （ 3 ）介紹了國內外破碎機的發展趨勢，以及雙轉盤沖擊破碎機這一新產品的結構和特點，並根據試機過程中出現的故障，建立了故障樹，並導出了導致故障發生的各種基礎事件； （ 4 ）研究了臨界轉速的計算方法和原理，用傳遞矩陣法計算出了破碎機內轉盤的臨界轉速。 -
We illustrate the wavelet package analysis that can obtain the time - frequency distribution figure of noise signal, which can be used to define gray - image. through image - average, we can get the standard time - frequency distribution images of different main bearing gap. based on that, a main bearing wear fault diagnosis model using image matching is set up
然後對圖像進行平均，得到主軸承在不同間隙狀態下的「標準」時頻分布圖，建立了柴油機主軸承間隙圖像匹配的故障診斷模型，匹配時所用的參數為兩幅圖像之間的歐氏距離。 -
By the result of these experiments, acoustic emission ( ae ) was chosen to use in the research. at the same time, we analyse the phenomenon of acoustic emission at the base of theory, the characteristic signal of acoustic emission which comes from the faulty bearing at the angle of application, and the expression of the characteristic signal. contrast was also made on the data achieved separately from vibrational signal and ae signal, and it is proved that ae is feasible and available to the diagnosis to the fault of the rolling bearing
主要工作有如下幾方面：對本段前期實驗室階段採用的振動法幅值域無量綱處理進行了分析，並研製了現場所使用的滾動軸承故障檢測裝置，將無量綱參數診斷法應用於段修現場，且做了大量試驗；對于現場試驗中所出現的問題進行了分析，提出將聲發射的方法用於軸承的在線故障診斷；從理論上分析了聲發射現象，從應用的角度分析故障軸承的聲發射信號的特徵以及聲發射信號特徵的表示方法，並在實驗室中，採用振動法和聲發射法實時檢測的實驗數據進行了對比和分析，證明了使用聲發射法對軸承故障檢測的可行性和有效性。 -
At present, the most of vtr which are used in watch - control occasion for speciality are short of a uniform control - check - alarm system, which brings on the discommodiousness of operation and the user can not know the time of occurring a fault, which reduces the reliability of the watch - control system. therefor, at first, i carefully analyze the servo theory of the vtr which had been produced by chmavc with k mechanism to find out the work rule of the control signal ; second, take out some right control signal ; then for dealing with the problem of vtr in use for watch - control, i choose some right components to design the uniform control system for many special vtr with protel software. it mainly includes the following functions : operation functions of all vtr ( for example : power, play, ff, rew, stop, rec, eject, fwd, rwd, sp, lp ) was controlled by line at the same time ; in, the process of recording, when the tape walks to the end or stops by itself, the system gives an alarm and shows the number of the wrong vtr ; in the process of recording, the system gives an alarm and shows the number of the wrong vtr when the video signal from vidicon is losed ; the system controls all vtr to record on the non - working time when there is something wrong in the guarding section ; the system controls the video from vtr to switch to right monitor
目前，用在監控場合的業務用錄像機普遍缺乏一個統一的控制及檢測報警系統，這就導致了操作的不方便和出現了故障用戶不知道，降低了監控系統的可靠性，為此，我首先對華錄松下生產的k機芯的錄像機伺服原理進行仔細分析，找出各個伺服控制信號的控制變化規律；然後從中選出合適的控制信號；針對目前錄像機在實際監控使用過程中存在的問題，選用合適的元器件；運用protel繪圖軟體，設計了這個多臺業務用錄像機的統一控制系統，她主要包括以下功能：錄像機操作功能（如power play ff rew stop rec eject及正尋反尋帶速設定等）的統一線控控制功能；磁帶在記錄過程中，磁帶到頭和磁帶自己「偷停」的報警，並要能顯示出具體是哪一臺錄像機；在記錄狀態下，攝像頭輸入信號丟失報警，並要能顯示出具體是哪一臺錄像機；在休息或其他不需要記錄時，一旦警戒區有情況，則控制所有機器自動進入錄像狀態的功能；從錄像機輸出的監控圖像信號對監視器的切換功能。 -
Digital signal processor ( dsp ) combined with repm bldcm, which build up a dc adjustable speed system, achieve to control multiple motor speed, positive and negative rotate, protect and fault exemine by a true single chip. design and present a electromagnetism scheme of repm bldcm used in electromotion chair drive system. select electronical components and chips in the drive board by contrast with variant drive mode. design the drive board principle picture, make a drive board pcb and debug it. design a principle picture with dsp core. workout the motor control code introduced popular programme modle. test the programme reliability and control performance by linking tms320lf2407 evm, pc, drive borad and the bldcm. the bldcm swatch is prepare experiment
本論文闡述了方波驅動稀土永磁無刷直流電動機的原理及數學模型；設計並給出了一種電動座椅用稀土永磁無刷直流電動機的電磁設計方案；對電機採用何種驅動方式進行了對比分析；對驅動電路進行了元器件選型、原理圖設計、制板及調試；有針對性的闡述了dsp在本系統應用中所涉及到的功能模塊；設計了以dsp為核心的控制電路原理圖；以模塊化的軟體編程思想編制了電機控制軟體；通過tms320lf2407目標板、上位機、驅動板及電機的聯調，證明了系統可行。 -
Among the many testing methods of analog and mixed signal circuits booming up in recent years, the pseudorandom testing technique is easier to generate testing stimuli and the current - based testing method could magnify the response differences between fault - free circuits and faulty circuits
近年來提出的很多種模擬及混合信號電路測試方法中，偽隨機測試法易於產生測試激勵，基於電流的測試法能使正常電路和故障電路的頻率響應的差別增大。 -
Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method
在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。 -
An automated de - noising algorithm based on the energy of wavelet packet not donoho ' s threshold algorithm is established. a gear feature vibration signal extraction method using the wavelet packet energy is proposed, which can separate gear meshing vibration, noise vibration and gear fault vibration signal from the original gearbox case vibration signal. basis pursuit ( bp ) algorithm is introduced into the filed of mechanical signal de - noising and feature extraction for the first time
第三章擺脫了donoho的閾值消噪思想，從能量的角度建立了基於小波包的自動消噪演算法；提出基於小波包能量分佈的齒輪故障特徵信號提取方法，可以將齒輪嚙合振動信號、干擾振動信號以及故障沖擊振動信號從原始齒輪振動信號中分離出來；首次將基追蹤消噪演算法引入到機械故障信號的消噪與特徵提取上，通過對齒輪故障信號的消噪，表明了它的有效性，並對影響該方法實際應用效果的因素進行了全面的分析，同時也指出了該方法存在的局限性。 -
In the second method, wavelet transform is combined with modal transform, and transient travelling - wave signal is used. after three phase signals are decomposed into their modal components, the wavelet transform coefficient of ground mode can be used to identify approximate position of fault, and the wavelet transform coefficient of aerial mode is used for identifying arrival time of traveling - wave
第二種方法將小波變換與模式變換理論結合起來，採用的是暫態行波信號，首先將三相信號轉換成模式分量，零模分量的小波變換系數用於判別故障的大致位置，然後利用線模分量的小波變換系數來確定行波到達時間。 -
The abrupt change informatiom can be obtained through decomposing and reconstruction of the vibrating signal by wavelet packet ; therefore the fault condition of the hydro - generator unit can confirm and provide decision support for diagnosing the vibration fault of the unit
運用小波包分析對振動信號進行分解與重構，可以獲得振動信號的突變信息，即可以獲得機組振動的故障狀況，從而?診斷機組振動的故障狀況提供決策支援。 -
The study of cab signal fault diagnosis based on pattern matching algorithm
基於模式匹配演算法的機車信號故障診斷的研究 -
Application of fourier transform and wavelet transform to signal fault diagnosis
傅里葉變換與小波變換在信號故障診斷中的應用
分享友人