sintering range 中文意思是什麼
-
The studies indicate that different content of pyrophyllite and dolomite can cause the following three cases : ( 1 ) making the refractory point decrease linearly and, to some extent, influencing the microstructure and properties of sintered body ; ( 2 ) acceleratingmullite formation during sintering, reducing thermal expansion coefficient of bond, reinforcing the matching nature and improving the flexural strength and shock strength ; ( 3 ) preventing sic grinding tool from generating black core, expanding suitable sintering temperature range of sic grinding tool
同時，也不同程度地影響了磨具燒結體的微觀結構和性能； （ 2 ）可促進在燒結過程中莫來石的形成，降低結合劑的熱膨脹系數，加強了結合劑與磨料的匹配性，提高了磨具的抗折強度和抗沖擊強度； （ 3 ）在一定溫度范圍內還可防止碳化硅磨具出現黑心現象，拓寬了碳化硅磨具的燒結溫度適應范圍。 -
The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors
研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。 -
If it is not good enough, optimal control module based on principle component analysis and clustering search will function for optimization. this algorithm makes no request for accurate analytical model and maintains search efficiency and self - adjusting performance by an optimal parameter set derived from process data, which is proved to be effective. by practical running of dcs, a prominent tracing performance is gained and variation of parameters is limited in a small range, which enhance stability and production benefit of sintering process obviously
燒結過程是一個影響因素復雜、干擾嚴重、具有不確定性的工業過程，傳統的基於對象精確解析模型的優化策略難以奏效，因此在控制參數優化模塊中提出了一種基於主元分析和聚類搜索的優化匹配演算法，該演算法不要求對象的精確模型，其搜索效率和自校正性能依賴于從生產過程歷史數據中抽取的優化參數樣本庫，充分利用了燒結生產過程積累的生產數據所包含的信息，取得了不錯的效果。 -
The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。 -
It was found that the introduction of ca2 + enhanced the sinterability of the material. the relative density of sintered specimens increase with the content of ca2 + in the composition range of 0 < x < 0. 3. it was confirmed that a high relative density can be obtained at relatively low sintering temperatures by using uniform, high surface area la1 - xcaxcro3 powders, which modifies the crystalline structure and microstructure of ceramic specimens
研究結果表明， a位ca ~ （ 2 + ）的引入在一定程度上能夠降低材料的燒結緻密化溫度：細小、均勻、高比表面積的粉料能夠有效降低材料的燒結緻密化溫度；燒結溫度的降低可以減少la _ （ 1 - x ） ca _ xcro _ 3中液相含量和鉻氧化物的揮發，有利於材料晶體結構、顯微結構的改善。 -
Design and application of sintering parameters optimized range control system based on industry field - bus
基於工業總線燒結區間控制系統的設計與實現
分享友人