sintering test 中文意思是什麼

sintering test 解釋
燒結試驗
  • test : n 1 檢驗，檢查；考查；測驗；考試；考驗。2 檢驗用品；試金石；【化學】試藥；（判斷的）標準。3 【化...
  1. Post - sintering test for uo and uo gdo nuclear fuel pellets

    Uo和uo gdo核燃料球粒后燒結試驗
  2. After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method

    經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。
  3. The reasons of high energy consumption on sintering machine no. 2 at xiangtan i & s co were discussed from the results of heat balance test

    摘要根據湘潭鋼鐵公司（以下簡稱湘鋼） 2號燒結機能耗現狀和熱平衡測試結果分析了該燒結機能耗高的原因。
  4. Abstract : in this paper, two tests are described on air leakage of sinter machine in 2 sintering plant of xiangtan iron and steel co. according to the test results, on the base of analysis and discussion, a series of measures on decreasing air leakage of sinter machine are putted forwored from sealed devices, lubricating oil system, maintenance and management etc. an effective and feasible way is supplied for energy saving and increasing production, decreasding production cost, increasing economy benefit of sintering process

    文摘:通過對湘鋼二燒燒結機漏風率的兩次測試和結果分析，從密封裝置、潤滑系統、附件結構的改進等方面提出了一系列降低漏風率的對策，為燒結工序的增產節能，降低生產成本，提高經濟效益提供了一條行之有效的途徑。
  5. Production test of mixed iron minerals of brazil in sintering at pinggang

    萍鋼二鐵燒結配加巴西鐵精粉的生產試驗
  6. Advanced technical ceramics - methods of test for ceramic powders - determination of the densification on natural sintering

    高技術陶瓷.陶瓷粉試驗方法.自然燒結的緻密化測定
  7. Design feature and test run of electric dust collector at the head of no. 3 sintering machine

    三燒機頭電除塵設計特點及調試運行
  8. Abstract : in one sintering plant, its no. 1 wagon tipper ' s track sur face occurred corrosive pitting and stacking only after short application, and th is effect the normal production seriously. in order to diagnose the plastic defor mation of the track surface, we made test and fem analysis to it, found the re ason of failure, and put out improving measure

    文摘:某燒結廠1號翻車機在使用較短時間后，導軌表面出現點蝕和堆邊現象，嚴重影響正常生產.針對這一問題，對導軌表面塑性變形進行了實測和有限元分析，從而找出了故障原因並提出了改進措施
  9. Orthogonal test of sintering conditions of q phase - ca - c12a7 high alumina cement

    7高鋁水泥燒成的正交試驗研究
  10. The composite hardness was increased comparing to copper due to the reinforcement effect of nanosized al2o3. and the density was related with the parameters of hot - press sintering processing. the dry sliding wear of the composites was investigated in a pin - on - disk wear test rig

    在自製的銷?盤式低載荷摩擦磨損試驗機上對復合材料進行摩擦磨損實驗，通過對實驗數據和sem形貌的分析，表明納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料有較好的抗磨損性能。
  11. The effects of the types and amount of rare earth elements as well as hot - pressing sintering temperature on the mechanical properties of fe - based metal bond and diamond composites either containing or not containing tih2 were studied by means of orthogonal test and variance analysis

    採用正交試驗和方差分析系統地研究稀土種類、添加量和燒結溫度對含tih _ 2和不含tih _ 2條件下鐵基胎體和金剛石復合材料力學性能的影響。
分享友人
分享到 Line

分享到臉書