small cone 中文意思是什麼

small cone 解釋
小鐘
  • small : adj 1 小 (opp large) 少 (opp large numerous) 細小的;窄小的;瑣細的;些微的;少額的(收入等)...
  • cone : n 1 圓錐,錐形物;錐面;錐體。2 火山錐,圓錐形火山;錐狀地區。3 【植物;植物學】球果,球花。4 風...
  1. That region of the plate is quite small and so the cone of diffracted rays, for the most part, misses it.

    相板上的這一區域是很小的,因此衍射光線錐的絕大部分不通過它。
  2. The cyclones with short cone are used for crude grading of minerals with heavier specific gravity in gold mines, sand gold mir. es and sulphur ore mines and have such advantages as small ground occupation, high capacity, high operating flexibility, low energy consumption and high movability etc

    短錐分選旋流器用於金礦、砂金礦、硫化礦等比重較大的礦物的粗選作業,具有佔地面積小,處理能力大,操作彈性大,能耗低,可移動性強等優點。
  3. One showed what may have been a small chip from an insulating tile falling off the underside of the shuttle ' s nose cone, shannon said

    沙農透露,其中的一部攝像機拍攝到一小塊隔熱瓦從航天飛機頭錐外部脫落。
  4. Consider the difference in appearance between a small seed from a pine cone, and the end result of that seed - - a towering adult tree

    例如,考慮種子破土而出的過程,漸漸長大變成粗壯的松樹。
  5. A piece of paper twisted into a cone and used to hold small wares such as candy or nuts

    圓錐形紙袋用紙捲成的錐形袋子,用來裝象糖塊或堅果等商品
  6. For small aperture ejection nozzle, especially to the p serial type that the center hole diameter is 4mm, its center hole and inner cone is always adopting imported numerical control machine to grind

    對于小孔徑的噴油嘴,特別是直徑為4mm的p系列噴油嘴的中孔座面的磨削,一直採用進口的數控磨床加工。
  7. From an open box on the majolicatopped table he extracted a black diminutive cone, one inch in height, placed it on its circular base on a small tin plate, placed his candlestick on the right corner of the mantelpiece, produced from his waistcoat a folded page of prospectus illustrated entitled agendath netaim, unfolded the same, examined it superficially, rolled it into a thin cylinder, ignited it in the candleflame, applied it when ignited to the apex of the cone till the latter reached the stage of rutilance, placed the cylinder in the basin of the candlestick disposing its unconsumed part in such a manner as to facilitate total combustion

    他從馬略爾卡瓷面桌子上的一個敞著的盒子里取出個一英寸高又小又黑的松果,將其圓底兒放在小小的錫盤上。然後把他的燭臺擺在壁爐臺右角上,從背心裏掏出一張捲起來的簡介附有插圖,題名「阿根達斯內泰穆」 209 。打開來,大致瀏覽了一下,又將它捲成細長的圓筒,在燭火上引燃了。
  8. The spinning forming experimental for cone cylindcr with small angle

    小角度錐形筒體旋壓成形試驗研究
  9. Fine material to be dewatered is fed to the small end of a revolving cone shaped screen basket. solids retained on the screen are transported out of the basket through the angle of inclination and the wiping action of a scroll rotating at a slightly higher speed. with this wiping action, there are no large off - center movements due to uneven distribution of the material in the basket

    該機適用於化工制藥食品冶金礦山等行業固液分離,分離懸浮液固相在10 % 80 %固相顆粒直徑在0 . 135mm 0 . 22mm效果尤佳范圍內的線狀或結晶狀的固體顆粒,如檸檬酸,古酸鹽果汁硫銨尿素等。
  10. The main object of this paper is to design a diagonal impeller, which requires small size and high rotating speed the first step of design is to solve the radial distribution of parameters at the inlet and outlet of the blade, such as pressure, temperature and velocity. and then, according to the radial distribution, we can design the diagonal impeller blade. blade elements are defined on a cone, which pass through the blade edge streamline location

    其設計思想是採用準三維設計方法,先進行二維流場計算,在葉片軸向間隙中設立計算站,應用數值計算方法計算葉片前後緣的壓力、溫度、速度等參數沿葉高的分佈,然後根據這些參數,選取若干個回轉面進行葉型設計;再將各回轉面上得到的基元葉型沿某一個積疊軸積疊起來形成三維葉片,最後對得到的三維葉片進行試驗,並對實驗結果進行分析比較。
  11. With the development of the new technology of drilling, the exploitation of deep well and over - deep well needs small size bit. because one - cone bit has the advantages of the three - cone bit and the pdc bit and it makes for their disadvantages, so the one - cone bit is the important chose to drill the small well

    隨著鉆探新技術的發展,開發深井和超深井技術要求鉆頭尺寸小型化,由於單牙輪鉆頭具有三牙輪鉆頭和pdc鉆頭的優點,同時又彌補了二者的不足。
  12. Hexagon head set screws with small hexagon and half dog point and flat cone point

    六角頭短圓截錐端緊定螺釘
  13. While in the cone shape mill barrel with cone shape rotor, although the process area is small, the energy density is more centralized, so the density and speed increase greatly and it can get high output

    錐形的研磨腔配以錐形的轉子,加工區域雖小,能量密度高度集中,在密度和速度上提高了很多,可獲得高產能。
分享友人