solid error 中文意思是什麼
solid error
解釋
固定誤差-
Compared with the behavior of macromolecules in real solution system, the adsorption information in the monte carlo simulation system, such as adsorption isotherm, surface coverage, and bound fraction, was studied for discussing its relation to simulation parameters. five - selection simple cubic lattice, self - avoiding walk, and nearest interaction model were used to construct the homopolymer adsorption model on the solid - liquid interface. periodic boundary conditions were used to reduce the fixed error from limited cubic lattice in size
模擬中採用五選擇簡單立方格子上的自迴避行走和最近鄰相互作用模型；使用周期性邊界條件以減小有限大格子空間帶來的系統誤差；用鏈節間相互作用能、界面吸附能、體相濃度和鏈長約束體系中的高分子的吸附行為；用末端轉動、 l -翻轉、曲柄運動、蛇形運動和r - r切除-生長法對模擬體系進行擾動；用系統達到吸附平衡后的樣本來研究模擬體系中的高分子鏈在固液界面上的吸附。 -
Nowadays, the machining center carries through the precision inspection only following the fixed coordinates " axes, which can not completely reflects the real error of the spacial position of the practical machining outside the axes and leads to having no the directive relation between the inspected precision and the practical machining precision. so, this paper introduces that the error factors of influencing workpiece ' s outline on machining and carries out the solid inspection of every spot ' s error inside the workaround on the horizontal machining center
本文針對當前加工中心僅沿固定的坐標軸線進行精度（含幾何精度和定位精度）檢驗，並不完全反映軸線外實際加工的空間位置真實誤差，導致檢出精度與機床實際加工精度無直接對應關系的現狀，論述了加工時影響工件型面輪廓精度之加工中心的誤差因素，對加工中心實施其工作區內各點誤差的立體檢測。 -
In order to meet the requirement of phase - error and physical dimension, high - pass / low - pass filter phase shifter and solid - structure are applied in the design of if broad - band five - bit digital phase shifter
考慮對相位誤差和物理尺寸的要求，中頻寬帶五位數字移相器採用高通/低通濾波器形式和立體結構進行設計。 -
On the basis of the finite element analysis of the press - mounting machine, to solve the modeling error of the previous modeling method, a new mixed - model method using the spring element and thin - layer solid element was introduced in this thesis. an experiment designed to test the interface static stiffness was carried out and the needed modeling datum was obtained
在對壓裝機進行了整體建模模擬的基礎上，針對壓裝機整體建模存在的誤差問題，本文提出了一種改進的彈簧單元和薄層實體單元混合建模的方法，並依此設計了螺栓結合面靜剛度測試試驗，通過試驗獲得了建模所需的參數。 -
Calculation of measuring error on solid surface temperature under steady conditions
穩定環境下金屬固體表面傳熱測溫誤差計算 -
At the same time, there exist the following problems : long design cycle, high error rate, large amount of repetitive modifying, lack of information share, etc. therefore, it is of great practical significance to develop one cad and software to solve the problems above and to be acceptable to the shapes and structure features of solid door
實木門的造型比較復雜，款式變化多，在設計過程中存在設計周期長，出錯率高，重復修改設計工作量大以及缺乏信息共享等問題，是傢具設計中的瓶頸。因此研究開發適合實木門的造型和結構特點、能夠解決上述問題的實木門計算機輔助設計方法和軟體具有重要的實用價值。
分享友人