solid velocity 中文意思是什麼

The semi - solid recrystallization velocity was run - up when the holding temperature risen and the heating velocity accelerated. 5

保溫溫度升高和連續加熱速度加訣都會使半固態再結晶的速度提高。

According to the " solid - particle " theoretical model, a theory model of the dynamic burning - velocity of a rocket - portfire in its igniting delay - time cannulation is established, a theory model of the dynamic delay - time is educed. the factors are analyzed, setting position and shape of a igniting delay - time cannulation that affect its igniting delay - time, the theoretical basis is offered to develop the high - level precision rocket - portfire in the air

本文根據「固體粒子」效應理論，建立了點火延期管動態燃速數學模型，導出了點火延期管動態延時控制的理論計算模型，分析了火箭空中點火延期管的安裝位置及其形態對其延期時間的影響，為高精度火箭空中點火具的工程研製提供了理論依據。

Abstract : solid propellant rocket motors are preferred for most ballistic missiles because they need simple maintenance and can be launched quickly. but the conventional thrust termination devices limit the depletion of every stage ' s grain and increase some extra - weight. an improved method for designing a multi - stage solid rocket based depleted shutdown was provided. in order to solve the problem of lack of thrust termination devices, a device to adjust the burnout angle will match the final burnout velocity and satisfy the desired range. the method can also limit the detection from anti - ballistic missile system

文摘:由於維護簡單和發射快速，彈道導彈多用固體火箭發動機，但繁雜的推力終止裝置使各級裝藥不能耗盡並讓結構增重.提出了一種對基於耗盡關機多級固體火箭概念設計的改進方法，此方法滿足導彈系統主要的戰技要求.為解決無推力終止裝置的末速不準問題，可在末級發動機採用姿態調整裝置，對射角進行調整，配合末速以滿足射程要求.本方法還可抑制敵方反導探測

The hydraulic gradients of settling slurry flow transported in three kinds of moving states, i. e. suspension, saltation, or partially suspension were investigated, based on analyzing the changes of solid particles and water in momentum, velocity and their mass related to momentum exchanging over the acceleration period of the solid particles

從固體顆粒加速期間清水與固體顆粒的速度變化、動量傳遞、相關質量等基本問題分析入手，研究了沉降性漿體在水平管道內流動時其固體顆粒在3種流動狀態下的水力坡度，提出了沉降性漿體在水平管道內流動的機理模型，進而用該模型對一些輸送條件下的沉降性漿體的水力坡度進行了計算。

Exploration on method of simulation and modeling for high - velocity steam - solid two - phase flow in supernormal parameters

超常參數條件下汽固兩相流動的相似與模化方法探究

The system of piv is constructed suitable for measuring the particle movement and the flow pattern of particle clusters is visualized in the cfb. under the low and high solid flux, this work also study the aggregate properties such as the two - dimensional shapes, velocity and existence time of clusters on several axial / radial positions

對循環流化床冷態實驗臺兩測試段進行了流型和顆粒團可視化研究，分別獲得了較低循環流率下過渡區和在高循環流率下稀相區顆粒團的運動速度，形狀，持續時間及其動態變化情況。

The quality of sand incipience involved with many kinds of parameters, such as incipient velocity, incipient angle etc. our research depends on the advantage of cross - knowledge and makes a research on this subject by gas - solid hydromechanics theory and ptv measure technology

本論文發揮交叉學科的優勢，採用氣固兩相流體力學理論和ptv測量技術研究這一現象，從新的角度認識沙粒起動和風沙流結構，為風沙流動的研究打開了新的思路。

Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments

文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。

In this paper, high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model. the distribution of gas velocity and pressure, the temperature field of gas and solid in the moving particulate bed are examined for different conditions. the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance. the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity. in the region of thermal penetration, the porosity of solid bed has significant effect on gas field and pressure loss. it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation. the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation

針對移動顆粒床中物料層內的高溫氣體滲流傳熱現象，考慮滲流與傳熱的相互作用，採用局部非熱平衡假設建立了多孔介質滲流傳熱物理數學模型並進行了數值計算.研究了不同情況下床內填充多孔介質中的流速、氣固溫度和床層壓力損失.計算結果表明，高溫熱氣對移動床顆粒料層的熱滲透主要發生在滲流入口端區域，增大入口滲流速度以及減小床層物料下移速度將導致物料溫度沿床高慢速下降，熱滲透深度擴大，熱滲透作用區域內的物料溫度水平提高.在熱滲透作用區域，孔隙率對流場和壓力損失有很大的影響.研究結果對于移動顆粒床反應器的設計與運行具有一定的參考作用

On the basis of published research of experts and scholars, relations among the velocity of water, that of solid particles and that of settling slurry have been established by the analysis of momentum transmission between water and solid particles in the upward inclined pipeline. then the calculation formulae for the upward - inclined - pipe hydraulic gradient are derived

本文在系統總結現有專家學者的研究成果基礎之上，通過分析向上傾斜管道輸送中清水與固體顆粒的動量傳遞過程，從動量守恆的角度建立了清水速度、固體顆粒速度和漿體流速之間的關系，進而推導出了向上傾斜管道輸送的水力坡度計算公式。

The velocity equation of stoneley waves at a liquid - solid interface

固體分界面處斯通利波的波速方程

During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。

Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition

通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。

The deposition rate of aerosol particles in capillary tube was measured with submicrometer monodisperse polystyrene spheres solid aerosol particles and pulse sample inserting technique ; and studies were made on the relationship between the flow velocity, the tube diameter, the tube length and aerosol particles size

摘要採用亞微米單分散聚苯乙烯球形硬氣溶膠粒子和脈沖進樣技術，測定了氣溶膠粒子在管道中的沈積率，研究了沈積率與流體速度、管道長度、管道直徑和氣溶膠粒子大小之間的關系。

For sand, glass bean, quartz sand and pvc, pressure fluctuations were measured at different conditions. furthermore, statistics analysis, power spectral density ( psd ) analysis and chaos analysis of pressure fluctuations in gas - solid cfb were conducted. an investigation of the effect of circulating solid flux, superficial gas velocity, height from riser bottom and particle property on the parameters ( e. g

本文測定了河砂、玻璃珠、玻璃砂和pvc四種顆粒在不同固體循環量、不同表觀氣速、不同軸向高度下的壓力波動，進而對氣固循環流化床壓力波動時間序列進行了統計分析、功率譜分析和混沌分析。

To ascertain how to produce differential pressure reasonably during the course of high temperature and pressure gas well testing, we must consider synthetically the following situations : both liquid in well bore and solid phase particles of mud in strata can be carried out through airflow ; we must avoid sand production out of borehole walls and make the selected differential pressure meet the demands of the testing instrument capability ; the calculation of differential pressure when no sand comes out of strata covers the calculation of strength of rock of borehole walls and airflow velocity, etc

摘要高溫高壓氣井測試中合理生產壓差的確定需要綜合考慮使氣流能夠在井筒中攜液、返排侵入地層中的泥漿固相顆粒、避免井壁出砂、滿足測試工具性能要求等；地層不出砂壓差計算還涉及到井壁巖石的強度計算、氣流流速計算等。

This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。

On the basis of piv measurement of the gas solid velocity field, the size and the numbers of particles are measured by newly developed image processing software. the results are identical with the variation of the factual size of particles. by the viable datum, the average size of particles in the cross section is calculated in the dilute phase area of circulating fluidized beds ( cfb ) riser

在piv測速系統基礎上，通過二次開發的圖像識別軟體，實現不同工況下各截面顆粒粒徑分佈的測量，測量結果基本反映出實際顆粒粒徑變化，證明了該方法的可行性，進一步獲得了循環流化床稀相區顆粒粒徑分佈特性。

The method for measuring solid velocity based on linear neural networks

基於線性神經網路測量固體速度的方法

An improved methal to measure the solid velocity in the gas - solid two - phase flow

兩相流固體速度測量的改進方法