solidification heat 中文意思是什麼
solidification heat
解釋
固化熱- solidification : n. 團結；凝固；【化學】固體化（作用）。
- heat : n 1 熱；熱力；熱度；熱量。2 體溫；發燒。3 （氣候的）高溫，暑氣。4 【冶金】熔煉的爐次；裝爐量；一...
-
In the process of solidification the same amount of heat is released.
在固結過程中則將釋放出同等的熱量。 -
Fesi2 - based semiconductors have been studied due to its good performance, low cost and potential application in power generation using waste heat. state - of - the - art techniques such as levitation melting, rapid solidification and hot uniaxial pressing ( hup ) were used for sample preparation in the present work. the phase transformation, micro structure and transport properties of the materials have been analysed with xrd, sem / edx, raman spectroscopy as well as thermoelectric characterization
在綜合評述國內外熱電材料研究新進展的基礎上，本文以懸浮熔煉、快速凝固和單軸熱壓等制備工藝為技術特徵，以mn或al摻雜fesi _ 2基合金為研究對象，採用xrd 、 sem / eds 、 raman光譜以及材料熱電性能測試等分析表徵手段，系統研究相變過程、微觀結構特徵及其對材料熱電性能的影響。 -
Heat transfer and solidification of the strand in continuous casting of steel bloom
大方坯連鑄過程中鑄坯傳熱及凝固行為的研究 -
Temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared
對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。 -
Abstract : temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared
文摘:對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。 -
Numerical simulation of heat field of inner combustion engine casting solidification
基於有限差分法的鑄件凝固過程熱應力場數值模擬的研究 -
In this paper, the numerical simulation problem of the liquid infiltration extrusion technology that includes high pressure infiltration, heat conduction, solidification and large deformation is solved successfully, which provides theoretic basis for the parameters optimization and the application of the process
本文成功地運用有限元分析軟體解決了集高壓浸滲、熱傳導、凝固和大變形為一體的液態浸滲擠壓工藝過程的數值模擬問題，為該工藝的參數優化和實際應用提供了理論依據。 -
The following is the experimental investigations on solidification process of stearic acid. the influences which the inlet temperature and reynolds number of the cooling water have on the solidification process are presented. figures that display how heat flux change versus time has been drawn and analyzed
然後是硬脂酸凝固問題的實驗研究，分析了換熱流體進口溫度、換熱流體re數大小對凝固過程的影響，繪制了凝固過程中熱流密度變化曲線，比較了螺旋肋肋寬對強化傳熱效果的影響。 -
Based on the established three - dimensional physical model, simplified terms, specified material parameters in thermal and physical properties, boundary conditions, and the calculation method of heat convection of cooling water, the numerical simulation and analysis on steady - state temperature field for continuous unidirectional solidification of niti shape memory alloy wire billets were proceeded under the condition of different combined parameters using ansys finite - element software
在建立三維物理模型以及確定材料熱物性參數、邊界條件與冷卻水對流換熱系數計算方法的基礎上，採用ansys有限元軟體對不同參數組合條件下鎳鈦形狀記憶合金線坯連續定向凝固的穩態溫度場進行了數值模擬。 -
Study of heat treating on twin - roll rapid solidification az91 magnesium alloy ribbons
91鎂合金帶材的熱處理工藝研究 -
The coupled turbulent flow field and temperature field are simulated by finite element method ; the influence of casting speed on the turbulent flow field and temperature field in the melting bath and the interaction between those two field are analyzed ; the variation tendency of the heat flux intensity between the melting bath and casting roll and law of variation with changes of casting speed in the process of solidification are given ; a comparison between the simulation results and experimental results demonstrates their good agreement ; and the mechanism of the heat flux variation is identified by analysis on the temporature gradient and development of solidification within the melting bath and its influence on the variation of the heat flux intensity
採用有限元法模擬了雙輥鑄軋不銹鋼過程的流熱耦合問題;分析了鑄軋速度對熔池內流場、溫度場的影響以及流場與溫度場之間的相互影響;給出了凝固過程中熔池與鑄軋輥之間的熱流密度變化趨勢及隨鑄軋速度的變化規律，並把此模擬的結果與試驗的結果相比較，吻合較好;通過熔池內溫度場及溫度梯度分析了熔池內凝固的發展及其對熱流密度變化的影響。 -
Abstract : according to the site condition of the bisc, a mathematical model of two - dimensional unsteady solidification and heat transfer was established for the bloom caster in the mold. the mathematical model was solved with a finite difference method to characterize the temperature profiles and thickness of the solidified shell in the mold, the effects of casting speed on thickness of the solidified shell are also studied
文摘:根據包鋼的現場條件，建立了大方坯連鑄機結晶器內二維非穩態凝固傳熱數學模型，採用有限差分法對數學模型求解，得出結晶器中鑄坯的溫度分佈規律和凝固坯殼生成規律，同時研究了拉坯速度對坯殼生成厚度的影響
分享友人