solution quenching 中文意思是什麼

solution quenching 解釋
固溶淬火
  • solution : n. 1. 溶解；溶液，溶體，溶劑。2. （補輪胎用的）橡膠水；〈美國〉藥水。3. 解決，解答 （of; for; to）; 解釋；（數學等的）解法，解式。4. 免除，解除。5. 【醫學】消散，消退。
  • quenching : n. 【機械工程】淬火；【物理學】淬熄。
  1. The results show that the chemosensor exhitits selective fluorescent quenching in the presence of aromatic organic acid in acetonitrile solution, and that the binding ability of the chemosensor with organic acid is in the order of p - cyanic - benzyl acid > p - chloric - benzyl acid > p - methoxyl - benzyl acid > benzyl acid

    結果表明，所合成的熒光分子在乙腈溶液中能選擇性識別芳香族有機酸，表現出熒光淬滅現象，其與有機酸絡合能力的大小依次為：對氰基苯甲酸對氯苯甲酸對甲氧基苯甲酸苯甲酸。
  2. Ht sub - factory : complete process of annealing, quenching, tempering, quenching and tempering, solution treatment etc

    熱處理廠：可完成退火，正火，回火，調質，固溶處理等工藝
  3. ( 3 ) solid solution with good solid solution ability were acquired by solid soluting treatment for 25 min at 540 c, 560 c and 580 c, respectively, after that water quenching was carried on. in the case of 580 c, the coarseness of the precipitation at grain boundaries did not happen, equi - part 120 did not emerge at the intersection of three grains, these suggest that over sintering did not happen

    6013合金實驗熱軋板材經固溶處理後於180時效4小時達到峰值硬度； （ 3 ） 540 、 560 、和580固溶處理25min 、水淬，得到了固溶充分的固溶體， 580的情況下晶界析出相未粗化、三晶粒交界處的角度未出現等分的120 ，表明未發生過燒。
  4. Aim : to analyze the mechanism, thermadynamic theoretical basis, dynamic mechanism and influencing factors of thermally induced phase separation ( tips ) in order to completely grasp the factors affecting the size, distribution and form of pores, so that the adjusted range of pore can be widened and the preparation of porous membrane can be repeated and controlled. methods : considering from the structural characteristics of tissue engineered materials, the methods of preparing porous membrane using tips technique, the hermadynamic theoretical basis, dynamic mechanism and influencing factors were analyzed, the problems and investigative directions in the future were also analyzed. tips technique is a process of phase separation of polymer homogenous solution under quenching, and it is suitable for diameter and structural form of the micropore materials prepared using tips are closely correlated with the kind and dispensing proportion of polymer attrnuant, polymer concentration and polymer molecular mass, etc. conducted, including determination of polymer - solvent system phase diagram, study of form and appearance of porous membrane of different thickness, study of form and appearance of porous membrane prepared with systems of different x, which is the parameter of polymer - solvent interaction

    目的:分析熱致相分離成膜過程的機理、熱力學理論基礎、動力學機制以及影響因素，以便充分掌握影響孔度大小、分佈、形態的因素，使孔度調控范圍得以拓寬，使多孔膜的制備能重復可控.方法:從組織工程材料結構特點出發，分析熱致相分離聚合物多孔膜的制備方法及該法成膜的熱力學理論基礎、動力學機制以及影響因素.並分析實驗中存在的問題及今後的研究方向.結果:以熱致相分離法可制備聚合物多孔膜.熱致相分離法制備多孔膜是高聚物均相溶液在淬冷條件下發生相分離的過程，它適用於上臨界共溶溫度型聚合物一稀釋劑二元體系.熱致相分離法成膜的過程，可以認為是旋節線機理佔主導地位.熱致相分離法制備的微孔材料，其孔隙率、孔徑大小、結構形態與聚合物稀釋劑的種類、組成配比、聚合物濃度、聚合物分子量等因素密切相關.結論:可採用熱致相分離技術制備多孔膜，通過改變不同的成膜條件可獲得一系列不同孔徑尺寸和孔徑分佈的多孔膜材料.對熱致相分離成膜過程中聚合物-溶劑體系的相圖測定，不同厚度的多孔膜形貌研究，不同x （聚合物-溶劑相互作用參數）體系所制備的多孔膜形貌等需深人研究
  5. The company deals with the heat treatment processing of various specification, type and kind of ferrous nonferrous metal, including anneal, quenching, hardening tempering, carburizing, solid solution, aging, vacuum heat treatment, high frequency treatment, blueing, nitriding and ion nitriding etc, the annual capacity of which is more than 18, 000t

    我公司可以承攬各種規格型號品種的黑色金屬有色金屬熱處理加工業務，包括：退火正火回火淬火調質滲碳固溶時效真空熱處理高頻處理發藍氮化離子氮化等。年加工能力22000餘噸，年加工產量出口佔70 % 。
分享友人
分享到 Line

分享到臉書