speed of grinding wheel 中文意思是什麼

speed of grinding wheel 解釋
砂輪轉速
  • speed : n 1 快，迅速。2 速率，速度。3 （汽車的）變速器，排擋。4 （膠片，照相紙）感光速度。5 〈古語〉興隆...
  • of : OF ＝Old French 古法語。
  • grinding : adj. 1. 磨的，適合於磨的。2. 折磨人的；難熬的。n. 粉碎，研磨；摩擦；〈口語〉填鴨式教學。adv. -ly
  • wheel : n 1 輪，車輪；輪狀物。2 〈口語〉腳踏車；【造船】艙輪；（汽車的）方向盤，駕駛盤；（制陶）轉盤；紡...
  1. Grinding wheel continues with an infinite number of hard, sharp and refractory grits on edge surface at a high speed of swing operation to cut and grind over the surface of work piece, and unceasing self - sharpening grains and pore continue to grind a tool for every kind of material

    砂輪是經由高速回轉運作中，以其在外緣表面植無數上千萬之硬銳耐溫之小磨粒連續在工作物表面切削磨除，且不斷的自生銳利顆粒與磨屑空隙氣孔，繼續對各種材料做磨削工作的一種研磨工具。
  2. Grinding feature is to use work piece for a slow - speed operation, and wheel spindle selects a high - speed revolution and offers a minor amount of in - feed to cooperate with mechanical spinde for forward and backward movement for finishing grinding jobs

    研磨特性是利用工作物做慢速運轉，而砂輪心軸采高速回轉並給予微量進刀配合機械心軸前後運動完成研磨作業。
  3. This machine is used for straight - line bevel cutting and bevel grinding and polishing for flat glass, in certain condition, it can be also used in bevel cuttig, bevel grinding and polishing for soft stone panel. the contrilling system adopts plc, it can accomplish automatic grinding cutting after entering processing parameter, convery speed adopts speed adjustment of fre quency conversion, direct drive of wheel head motor, all motions for joining in parameter adjustment completely adopt straight - rolling guide - track with front beam and wheel head lifting lntegrally. the transmission of input and output adopts synchronization tooth belt and photo - electricity switch positioning, and position limitation of two pass is much more reliable

    Sxm371pa型玻璃直線斜邊磨邊機是用於玻璃直線斜邊斜切，斜磨及光拋的專用設備，在一定條件下也可以用於軟石板材的斜切斜磨及拋光。控制系統採用plc控制。輸入加工參數后可自動完成磨削傳送速度採用變頻調速，磨頭電機直接傳動，所有加工參數調整運動副全部採用直線滾動導軌，前梁與磨頭整體升降，輸入輸出傳送採用同步形帶，光電開光定位，雙行程限位更安全可靠。
  4. Analysis of strength in high speed rough grinding wheel of large diameter

    大直徑高速粗磨砂輪的強度分析
  5. Abstract : the effect factors of grinding roller surface roughness areanalyzed and experimented. the law of effect factors such as roller rotary speed, grinding wheel granularity, grinding liquid and so on, about roller surface roughness is obtained. the mathematical model of roughness is established through regression

    文摘:對影響磨削輥面粗糙度的因素進行了系統分析和實驗研究，得出了軋輥轉速、砂輪速度、砂輪粒度、磨削液等因素對磨削輥面粗糙度影響的一般規律，利用回歸分析的方法建立了粗糙度的數學模型。
  6. The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement

    研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。
  7. By using a wafer - rotating grinding machine, the influence of the main process factors including grit size of diamond grinding wheel, rotating speed of the wafer chuck table, rotating speed and the down feed rate of the cup grinding wheel on the material removal rate, spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated

    摘要利用基於自旋轉磨削原理的矽片超精密磨床，通過試驗研究了砂輪粒度、砂輪轉速、工件轉速及砂輪進給速度等主要因素對材料去除率、砂輪主軸電機電流以及磨削后矽片表面粗糙度的影響關系。
  8. Sxm261 sxm261b is processed with two diamond wheels, and base modification with one wheel, refining with three wheels, polishing with three wheels. the grinding and polishing speed is regulated by astepless device. this is an ideal machine with the characteristics of being easily handled and maintained, which is an improvement of the previous products turned out by our company

    Sxm261 sxm261b型玻璃直線斜邊磨邊機採用二輪磨削，一輪修底邊，三輪精磨，三輪拋光的設計。無級變速器調整加工速度，氣動拋光。此設備操作容易，檢修方便，是我公司在上一代產品基礎上改良而成的理想設備。
分享友人
分享到 Line

分享到臉書