spiral flow test 中文意思是什麼
spiral flow test
解釋
螺旋流動試驗-
In this thesis hydraulic experimental studies and theoretical analyses on the vortex - flow drop shaft were conduced and the following results were accomplished : ( 1 ) in the model test some hydraulic characteristics including the shape of air core in the center of the drop shaft, the radial distribution of water flow velocity and the distribution of pressure on the wall of the drop shaft were measured under the condition of high water head above 250m and large discharge above 1400m3 / s. ( 2 ) a kind of computational method for the spiral water flow in the air core region of drop shaft was discussed and applied and the results agree the experimental data well. ( 3 ) the total ratio of energy dissipation in the drop shaft can reach 90 % and the energy dissipation in every region was discussed quantitatively
本文通過試驗研究與理論分析對旋流式豎井泄洪洞應用於高水頭、大泄流量情況時存在的一些水力學問題進行了研究和探討，取得以下主要成果：一、結合小灣工程導流洞改建，對高水頭（ 252m ） 、大泄流量（ 1400m ~ 3 s ）條件下旋流式豎井中的水流運動特徵進行了比較全面的測量，包括空腔形態、徑向流速分佈及井壁壓強等；二、提出了豎井空腔段螺旋水流水力計算方法，其計算結果與實測值吻合良好；三、利用試驗與計算結果，對旋流式豎井的消能機理進行了探討，對豎井各部分的消能能力有了總體認識；四、對豎井下部消力井的合理井深進行了優化試驗研究，發現消力井合理深度為0 . 9d左右；五、通過試驗研究，歸納出豎井水流總摻氣量估算方法，為導流洞排氣方案的設計提供了參考依據；六、在高水頭、大流量條件下，豎井空腔段下部流速很高，盡管水流螺旋運動引起的離心力可以確保井壁壓強保持正壓，但空化數依然較低，因此豎井的空化空蝕始終是工程界關注的重大問題。 -
08. 02 test method for spiral flow of low - pressure thermosetting molding compounds
低壓熱固性模塑料的螺線流動度的試驗方法 -
Spiral flow test
螺旋流動試驗 -
Other content in this paper is the design and investigation of spiral inlet port. the geometries that compose intake port have been repeatedly when intake port scheme was designed. the intake port scheme has been carried out steady - flow test. the experiment data has been analyzed and investigated, then the performance of inlet port has been estimated by the fluid coefficient and the whirl ratio. at last, the spiral inlet port scheme has been selected based on matching relation of the factors of combustion system. in addition, how to " intake port synthesis performance coefficienf ' evaluate engine intake port has been discussed
本文的另一項內容是螺旋進氣道的設計和研究。通過對進氣道的幾個主要結構參數進行反復修改擬定進氣道方案，並對其進行穩流試驗，分析和研究試驗數據，利用流通系數、渦流比進行進氣道性能評估，根據燃燒系統要素的匹配關系，確定了兩種螺旋進氣道方案。另外，本文探討了「進氣道綜合性能系數」對發動機渦流進氣道性能的評估能力。 -
Standard test method for spiral flow of low - pressure thermosetting molding compounds
低壓熱固性模塑料螺旋形流動的試驗方法 -
Test analysis of ecosystem on functional groups of microorganism in spiral up - flow reactor system
系統中微生物菌群生態功能的試驗分析
分享友人