stacking test 中文意思是什麼

stacking test 解釋
堆積試驗
  • test : n 1 檢驗，檢查；考查；測驗；考試；考驗。2 檢驗用品；試金石；【化學】試藥；（判斷的）標準。3 【化...
  1. Basic tests for transport packages stacking test using compression tester

    採用壓力試驗機的堆碼試驗方法
  2. Basic tests for transport packages - stacking test using compression tester

    運輸包裝件基本試驗採用壓力試驗機的堆碼試驗方法
  3. Complete, filled transport packages - method of test for stacking using compression tester

    整包運輸包裝件.壓縮試驗機用堆放試驗方法
  4. Methods of test for verification of stability of industrial trucks operating in special condition of stacking with mast tilted forward

    工業用帶前傾起重桿的碼垛貨車特殊條件下工作穩定性驗證試驗方法
  5. Containers must be redelivered clean. note permissible weight limits for road and rail transport. the technical details of 1cctank container for yellow phosphorus : working pressure : 0. 4mpa test pressure : 0. 6mpa external dimensions ( lx w x h ) mm : 6058 x 2438 x 2591 maximum gross : 30480 kg stacking height : 9 x 30480 kg insulation

    這種罐箱容量大，密封性能好，使用周期長，抗振強度高，不易被損壞，操作方法實用；而我國現在使用的250l塑料桶，其回收或處理成本高，且污染環境，所以iso1cc黃磷罐式集裝箱是一種理想的替代塑料桶的貯運設備。
  6. In this research, fatigue life of laminate composite is predicted phenomenologically, dealing mainly with in - plane stresses without accounting for out - of - plane failures such as delamination. fatigue modulus is used as a physical parameter which helps to describe the basic fatigue behaviour of unidirectional laminates and obtain expressions for cumulative damages defined by strains. based on some typical fatigue test data for unidirectional composite laminates, a cumulative fatigue damage model is presented for predicting the fatigue life of multidirectional laminates with arbitrary stacking sequence under complicated fatigue loadings

    本文以碳纖維/樹脂基t300 / qy8911層壓結構為研究對象，從唯象的觀點出發，以疲勞模量為參量構造損傷函數，基於幾組最典型的單向板疲勞試驗數據，建立單向板在多軸循環應力作用下的疲勞壽命模型，並以此為基礎，發展同種材料體系的任意鋪層形式的多向層壓板在復雜循環載荷作用下的疲勞壽命預測方法。
  7. Industrial trucks operating in special conditions of stacking with load laterally displaced by powered devices - additional stability test

    用電動設備橫向碼放貨物的特殊條件下的工業用卡車.附加的穩定性試驗
  8. Abstract : in one sintering plant, its no. 1 wagon tipper ' s track sur face occurred corrosive pitting and stacking only after short application, and th is effect the normal production seriously. in order to diagnose the plastic defor mation of the track surface, we made test and fem analysis to it, found the re ason of failure, and put out improving measure

    文摘:某燒結廠1號翻車機在使用較短時間后，導軌表面出現點蝕和堆邊現象，嚴重影響正常生產.針對這一問題，對導軌表面塑性變形進行了實測和有限元分析，從而找出了故障原因並提出了改進措施
分享友人
分享到 Line

分享到臉書