static mesh 中文意思是什麼
static mesh
解釋
靜態網格-
In this article, the shp measure system based on the hardware of pci - 9114 ( daq ) and coordinator u511 is developed in vc + +. this system is good at getting the pressure data in the space mesh and processing it into velocity, total and static pressures and the field picture
本文通過vc + +開發了數據採集和處理一體化的基於pci - 9114數據採集卡和u511坐標控制器的七孔探針測試系統，該系統能自動採集空間網格點上的壓力數據，然後處理成所需的速度和總靜壓數據，並完成初步的流場繪圖。 -
W - type static dust removal filter mesh, with large filter area, longer service life
W型靜電除塵濾網，過濾面積更大，使用壽命更長 -
3d nonlinear finite element method, compatible displacement method of different mesh and response spectrum of mode - superposition are used to analyze the intake tower - intake slope static and dynamic interaction, since the complexity of geologic structure. the rational results provide a feasible way for the similar projects analysis in the future
論文採用三維非線性有限元法、非一致網格位移協調解法、振型分解反應譜法對復雜地質條件下的百色水電站進水口邊坡與進水塔的相互作用進行了靜、動力分析，得出了一些合理的結論，為今後類似的工程計算分析提供了一種可行的方法。 -
First, the basic theory of static load sharing mechanism has been presented, mainly including manufacturing and assembly error of each gear component ' s axis and each bearing ' s axis, gear size ( tooth thickness ) errors, simultaneous error of middle two - tooth. the formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed. second, the influences of each error on the static load sharing coefficient have been discussed
首先，從靜力學的角度研究了星型齒輪系統均載的基本原理；確定了影響齒輪系統均載特性的製造和安裝誤差，主要包括：各個齒輪構件的中心軸線製造和安裝誤差、軸承中心軸線的製造和安裝誤差、齒厚偏差、雙聯星輪同時嚙合線誤差；推導了這些誤差的當量嚙合誤差的計算公式，分析了系統的均載特性。 -
This static finite element modeling method does n ' t need the requirement of the dynamic design of product in the modern industry. otherwise, most work on the surface mesh generation is based on the single trimmed surfaces, and the work to closed surface and combined surface, which are very popular in engineer, is very few
另外，在曲面網格劃分方面，當前的研究大多是針對單張非閉合曲面進行的，對于閉合曲面和組合曲面的研究甚少，而這些曲面在實際工程中卻是經常使用的。 -
An innovative strengthening scheme for reinforced concrete space beam - column joints using high strength steel wire mesh and polymer mortar jacket was proposed, and the quasi - static tests of three reinforced concrete beam - column joints with floor slab and transverse beams were performed to verify the efficiency of the strengthening scheme
摘要提出了採用新技術高強鋼絞線網片聚合物砂漿加固技術提高鋼筋混凝土空間框架節點抗震性能的方法，並通過3個帶有直交梁和樓板的空間框架節點試件的低周反復加載試驗對該加固方法進行了檢驗。 -
The mesh data of these two models comes from static and modal finite element analysis respectively, and their load data possesses internal successivity. according to the correlation, finite element models support me parallel and cooperative processing of static, modal and dynamic response analysis
其中的結構瞬態響應有限元分析模型分為兩個層次的模型，其網格數據分別來自於靜態和模態分析有限元模型，在載荷數據上具備內在繼承連續性。
分享友人