static test circuit 中文意思是什麼
static test circuit
解釋
靜態檢查電路-
Dds951 series electronic single - phase electric meter is the most advanced static electronic meter in china. the meter designs use large - scale intergated circuit. high reliability step motor, it can the ac single - phase active energv voltage rating : 220v : frequency 50hz, positive and negative two directions and accumulates in one direction. the test singnal is isolated by phototransistor : it also has the function of anti - fraud, and indicates it s operation situation on flash light, so it could be managed very easy
Dds951單相電子電能表，是金雀儀表公司開發的新型電度表。該產品是採用規模專用集成電路，高可靠性步進電機等先進技術製造的國內最新電能試題新產品，用來計量額定電壓為220v ，頻率為50hz的交流單相有功電能，該產品能夠精確計量正負兩方向的有功電能，且以同一個方向累計。 -
By the comparison and analysis of different theory calculations and test results, the evaluation of theory calculation methods for analyzing mechanical characteristics of permanent magnet bearings is made : the calculation of static magnetic circuit is simple, which owns less mathematical model parameters, but its accuracy is not high
通過將各種理論方法和試驗結果進行比較和分析，對各種永磁軸承力學特性的理論方法進行了評價。得出了以下結論:靜磁路法計算過程簡單，數學模型的參數少，但計算精度不高。 -
The hardware circuit design include : industrial control computer configuration, selection of industrial control board type, design of the power supply and monitoring interface circuit, design of signal processing interface circuit ( the constant current source circuit, the time base signal processing circuit, the processing circuit for the signal to be measured ), design of panel control circuit, design of the system self - checking circuit, and etc. the program flow hart include : main program flow chart, system boot - strap self - checking program flow chart, manual static testing program flow chart, semiautomatic static testing program flow chart, automatic static testing program flow chart, dynamic testing program flow chart, transient testing program flow chart, source voltage and current monitor program flow chart, investigate function testing program flow chart, and etc. the measure system offers six working power supplies, the signal of time base, the signal of constant current source, sine wave signal and step to leap signal, and measures the frequency of the output pulse signal of the wide range pulse convert circuit accurately under three kinds of different test state ( static form, dynamic form and transient form )
硬體電路設計包括：工控機配置、工控板卡選型、產品電源及監控介面電路設計、信號處理介面電路（恆流源電路、時基信號處理電路、被測信號處理電路）設計、面板控制電路設計、系統自檢電路設計等。程序流程圖包括：主程序流程圖、系統開機自檢程序流程圖、手動靜態測試程序流程圖、半自動靜態測試程序流程圖、自動靜態測試程序流程圖、動態測試程序流程圖、暫態測試程序流程圖、電源電壓和電流監控程序流程圖、研究功能測試程序流程圖等。測試系統提供六路工作電源、時基信號、恆流源信號、正弦波信號和階躍信號，並對三種不同測試狀態（靜態、動態、暫態）下大量程脈沖變換電路輸出脈沖信號的頻率進行精確測量。 -
First, variable speed constant frequency wind energy convertion theory is described in this paper, then presents a review on the development of wind turbines control and the main types of generator and static converters used to interface variable speed wind turbines to the electric grid. then discuss main circuit constructure and advantage of direct drive wind energy conversion system and introduce pitch - control method for wind power traction and electric power stability. simply aerodynamic characteristic of the turbine is analysised and permanent magnet synchnonous generator math model is established. to convert the variable frequency electricity into utility grid, back to back four - quadrant pwm - vsi is used and three typies of control strategy is presented to capture the maximum wind energy and transmit energy. then simulation is implemented to test the control strategy. in the following chapter a simple ac - dc - ac converter with a dc - dc boosting chopper is proposed to transmit the wind energy into electricity energy and two control strategy is presented
建立了永磁電機和變流器的數學模型，針對雙pwm變頻器的特點提出了三種控制策略對變流器進行控制，通過變流器交-直-交的變換，將發電機發出的變頻變幅值交流電轉化為可用的恆定頻率的交流電，通過pwm調治能使其輸出功率因數為一，並且該控制系統功率因數為可調，能在特殊情況下同電網交換一定的無功功率，並通過對變流器的控制實現了最大風能俘獲的功能。最後採用matlab / simulink進行了模擬，取得了良好的模擬效果。在風力發電系統中，採用先進的最大功率俘獲演算法，能有效的從風中獲得最大的能量。 -
As for the dynamic performance, the linear variable differential transformer ( lvdt ) displacement sensor using signal conditioner ad598 is not so good, so the differential rectifier is designed as the measuring circuit of the sensor so as to increase its cross - over frequency. also, the static test and dynamic test is made for the sensor along with the lvdt
由於使用線性差動變壓器信號處理晶元ad598為測量電路的差動變壓器式傳感器的動態性能不夠理想，本文設計製作了差動整流電路作為差動變壓器式傳感器的測量電路以提高傳感器的截止頻率，並對差動變壓器式傳感器進行靜態和動態標定。
分享友人