steam ratio 中文意思是什麼

steam ratio 解釋
汽比
  • steam : n 1 蒸汽，水蒸氣，水氣，霧，蒸氣壓力。2 〈口語〉精神，精力，氣力；怒氣。3 輪船，乘輪船旅行。vi 1 ...
  • ratio : n. （pl. ratios）1. 比，比率，比值；比例；系數。2. 【經濟學】復本位制中金銀的法定比價。vt. 1. 用比例方式表達；求出…的比值；使…成比例。2. 將（相片）按比例放大或縮小。
  1. Abstract : based on the analysis of the mathematics models of saturation steam density and superheat steam density the paper states that the deviation of the detection on temperature highly affects the accuracy of intelligent flow totalizer. especially for saturation steam ， the accuracy of the temperature detection circuit shall be designed higher than the accuracy of the instrument. thus a temperature detection circuit based on ratio method with high accuracy is introduced

    文摘:在分析飽和蒸汽和過熱蒸汽密度的數學模型的基礎上指出，溫度檢測的偏差對智能流量積算儀的精度影響極大，尤其是飽和蒸汽，測溫電路的精度應設計為遠高於儀表的精度，同時引入一種基於比率法的高精度測溫電路。
  2. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  3. Result of numerical simulation shows that the grads of continuous phase " s velocities decreases with the presence of microbubble of which the diameter is 100 / / w, the profiles of air volume fraction in the boundary layers is similar to triangle or echelon, affected by interaction among the particle, there is a saturated air fraction, within the scope of saturated air fraction, increasing the air injection ratio can accrete the friction reduction ratio, under the condition of same air injection ratio, the free - steam velocity is larger, the effect of friction reduction is worse

    計算結果表明，直徑為100 m的微氣泡能減小近壁面連續相的速度梯度；微氣泡在邊界層中的濃度分佈近似為三角形或梯形分佈；受粒子間相互作用的影響，存在一飽和濃度；減阻率隨噴氣量的增大而增大，直至飽和噴氣量，此後，增大噴氣量，壁面摩擦阻力變化不大；相同噴氣量下，來流速度越大，減阻率越低。
  4. Advantages : the machines is higher versatility, when light and thin materialis processed no adjustment is need to smooth fabric running ; it it process shorten time, total processing time as 5 hour ( dark shape ) ; lower liquor ratio, liquor ratio of 1 : 4 ~ 5 and smooth fabric running are maintained of capacity of within 70 ~ 100 % ; reduction of electrical power consumption, reduction of water consumption 、 steam electricity, saving on effluent treatment

    優點：本機具有適應性更強：在處染輕、薄織物時，不作任何調節，能使織物運行流暢；工藝時間更短，處染織物（深色）全程總耗時可減到5小時；浴比更低，在每管載量70 % ~ 100 %范圍內染色浴比可保持在1 ： 4 ~ 5 ；用電省，節約了水電汽，減少污水處理費用。
  5. Three schemes for this technology were given, including air - blown gasification, recycle gas - blown gasification and steam & recycle gas - blown gasification, which were computed and analyzed. due to different conversion ratio of coal and different temperature that gas enters into gas turbine, the different results were got and analyzed, such as gas heat value, gasification efficiency and generation efficiency

    本文針對空氣氣化方案、再循環煤氣氣化方案以及水蒸汽+再循環煤氣氣化方案對煤部分氣化聯合循環發電系統進行計算分析，根據不同的碳轉化率以及煤氣進入燃氣輪機前不同的溫度，得出不同的煤氣熱值、氣化效率、發電效率等，並進行了分析，提出了適合不同目標工業應用的煤部分氣化方案。
  6. Study on the preparation techniques of lb high temperature shift catalyst at low steam to gas ratio

    型節能高溫變換催化劑的制備工藝研究
分享友人
分享到 Line

分享到臉書