steel drop 中文意思是什麼
steel drop
解釋
鋼粒-
This paper discusses how to improve expand section ' s lining of heavy - calibre and high - tempreture, the steel - fibre lining is improved to be the lining of firebrick and fireproof material, to avoide the lining drop and meet the needs of production
摘要闡述了如何將大口徑高溫膨脹節襯里由鋼纖維雙層襯里改為耐火磚加耐火澆注料結構,避免了襯里脫落,滿足了生產需要。 -
Kai xuan - check cast steel valve in the fully open state, almost unimpeded fluid pressure, the pressure drop through the valve relatively small
旋啟式止回閥在完全打開的狀況下,流體壓力幾乎不受阻礙,因此通過閥門的壓力降相對較小。 -
Steel measuring tapes for drop centre rims for bicycles
自行車凹式輪輞用鋼測量捲尺 -
A price drop in raw materials also led to a drop in the companies profit growth, he said. the government has taken a raft of measures to try to cool the economy, including raising bank reserve requirements three times and curbing unwanted fixed asset investment projects in red - hot sectors such as cement and steel
目前大金的每年產量約為7000臺,新生產基地設計產能為13000臺,建成后將是國內最大的客車生產基地之一,第一期項目主要生產大中型客車,其中大型佔60 % ,中型佔40 % ,一期工程投資2億人民幣,預計2005年完工。 -
Standard specification for copper - clad steel electrical conductor for catv drop wire
用於catv用戶引入線的包銅鋼電導線的標準規范 -
Anti - static polyester : steel and iron manufacturing facility, cement facility, facility including the risk due to fine dusts, high anti - static polarity ( 105 - 108 / square ), low pressure drop, good dust cleaning
抗靜電滌綸:鋼鐵製造設備,水泥設備,一些容易因小火而導致損害的儀器設備;強抗靜電,極性( 105 - 108每平方) ,低壓降,除塵率好。 -
Steel forgings ; design of drop and press forgings ; machining allowances, drafts, edge radii, fillet radii, base thicknesses, wall thicknesses, rib widths, and rib radii
鋼鍛件.落鍛和壓鍛設計.第2部分:加工余量拔模斜度 -
Steel die forgings - tolerances on dimensions - drop and vertical press forgings
鋼模鍛.公差和尺寸.落錘或垂直壓力鍛造 -
The present research situation of molten steel temperature drop of ladle in steelmaking plants is described
摘要介紹了煉鋼廠鋼包內鋼水溫降研究的現狀。 -
Drop - weight tear tests of steel pipe
輸送鋼管落錘撕裂試驗方法 -
Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings ; german version en 10243 - 1 : 1999, corrigenda to din en 10243 - 1 : 2000 - 06 ; german version en 10243 - 1 : 1999 ac : 2005
鋼模鍛件.尺寸公差.第1部分:落錘鍛造件和垂直壓力鍛 -
Drop forged steel bench vice
鍛鋼臺虎鉗 -
This paper discusses how to improve large taper lining, the steel - fibre liningis improved to be tortoise - shell net structure, to avoid the lining drop and remove a hidden danger
摘要闡述了將沉降器大型錐體襯里由鋼纖維單層襯里改造為龜甲網加耐火澆注料結構,避免了襯里脫落,消除了安全生產隱患。 -
The results show that, compared with rectangular steel tubular frame, crft frame have higher lateral stiffness, bearing capacity and better behavior of ductility ; crft braced frame has high lateral stiffness and bearing capacity, it ' s load bearing capacity does n ' t have remarkable drop after bucking of brace, which indicates its good behavior of ductility
研究結果表明:與方鋼管框架相比,方鋼管砼框架具有更高的剛度、延性和承載力;方鋼管砼支撐框架剛度大、承載力高,在支撐壓曲后,承載能力沒有大幅度的降低,具有良好的延性。 -
Abstract : to analyze the temperature of the ladle completely and control it reasonably, the temperature drop behaviors of the molten steel in the ladle under various conditions were studied through establishing a proper mathematical model. the results provide a theoretical basis for reducing the temperature drop and decreasing the tapping temperature of the molten steel in the converter , and for formulating proper temperature system of the liquid steel
文摘:為全面分析,併合理控制鋼包溫度,通過建立合理的數學模型,對鋼包熱行為進行模擬,分析了不同情況下鋼液的溫度下降行為.為減少鋼液溫降、降低出鋼溫度、合理制定鋼包溫度制度提供了一定的依據 -
Drop tester, or hoist with suitable sling and tripping device. surface on which packaged product is to be dropped must provide a flat, non - yielding base such as steel, concrete, etc
測試者或落下測試機須用適合且快速的裝置來進行落下,已包裝的產品要被落下於一平坦且堅硬的面,像鋼鐵、混凝土。 -
Such measures as raising baking temperature of ladle, quickening thermal circulation of ladle, adding insulating lay in ladle lining, adding cover in molten steel surface, adding ladle cover in casting are introduced to reduce molten steel temperature drop in this paper
闡明了通過提高鋼包烘烤溫度、加快鋼包熱周轉、包襯加隔熱層、鋼水表面加覆蓋劑、澆注鋼包加蓋等減少鋼水溫降的措施。 -
Prediction model for temperature drop of steel in cas - ob refining with powder injection
噴粉精煉溫降預測模型 -
Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings
鋼模鍛件.尺寸公差.第1部分:模鍛壓力和垂直壓力鍛造 -
Means of packaging - non - removable head tight head and removable head open head drums made of steel - drop handle
包裝方法.鋼制非移動蓋和移動蓋式鼓形桶.跌落處理
分享友人