strain annealing 中文意思是什麼
strain annealing
解釋
應變退火-
Zircaloy - 4 sheet, which was cold - worked followed by recrystallization annealing, exhibits longer lcf life in the rolling direction than that in the transverse direction, and the fact that difference in lcf life between both directions becomes larger as the range of plastic strain becomes lower can be attributed to the texture effect, p - solution treatment deteriorates the alloy ' s lcf property because the treatment lowers the average value of alloy ' s schmid factors, and the subsequent annealing - treatment in a - phase range has a impact on the lcf properties, i. e. the subsequent annealing - treatment at 500 ? for 1. 5h results in better property than that at 750 for 1. 5h, which comes mainly from the fact that the alloy annealled at 500 for 1. 5h has lower amount of the precipitate particles than the alloy annealled at 750 for 1. 5h
對于冷加工后經再結晶退火處理的zr - 4合金，軋制方向的低周疲勞壽命比橫向要大。隨著_ p的降低，兩個方向的低周疲勞壽命的差別相應增加，這是由於合金中存在織構的緣故。冷加工后經再結晶退火處理的zr - 4合金在固溶處理后，抗疲勞性能明顯降低，這主要是由於固溶處理降低了合金的schmid因子；固溶處理后在相區的退火對疲勞性能有影響，即500 1 . 5h退火的抗疲勞性能要優於750 1 . 5h退火，這主要與500 1 . 5h退火的合金中沉澱相粒子的數量較少有關。 -
Sige simox : oxygen ions with high dose were implanted into sige grown directly on silicon substrate for the first time, and sige - oi novel structure was formed successfully with additional high temperature annealing ; it has been confirmed that oxygen implantation with 45kev, 3 1017cm - 2 and annealing at 12500c in ar + 5 % o2 for 5 hours, are fit for the formation of sige - oi structure ; ge loss during the high temperature annealing has been observed, which is originated from ge volatility and ge diffusion ; it has been proposed to use nanoporous layer induced by h + / he + implantation to surppress ge diffusion and to use surface oxidation to overcome the upper limit of sige simox. sige smart - cut : hydrogen ions were implanted into sige material and followed by high temperature process ( 4000c to 7000c ) ; blistering study was done and suggested the possibility of sige layer transfer by smart - cut technology ; it is concluded that the bubble formation is easier in sige than in si, and the strain in sige / si and the difference of binding energy in sige and in si could possibly contribute to this effect. behavior of sige / si implanted with hydrogen : gave a detailed study on sige implanted by beamline or phi hydrogen implantation ; it has been found that great strain is introduced into sige by hydrogen implantation and this strain could be alleviated by high temperature annealing ; both for conditional beamline implantation and piii hydrogen implantation, 600 is appropriate for the post - implantation treatment
Sige - simox工藝方面：首次採用硅（ 100 ）襯底上直接外延的100nm厚sige的樣品中注入高劑量的o離子，通過退火處理成功制備了sige - oi新結構，即sige - simox工藝，證實了以45kev注入3 10 ~ （ 17 ） 7cm ~ （ - 2 ）劑量的氧離子，隨后在氧化層的保護下經1250 ， ar + 5 o _ 2氣氛的高溫退火（ 5小時）過程，可以制備出sige - oi新型材料；實驗中觀察到退火過程中的ge損失現象，分析了其原因是ge揮發（ ge通過表面氧化層以geo揮發性物質的形式進入退火氣氛）和ge擴散（ ge穿過離子注入形成的氧化埋層而進入si襯底中） ，其中ge擴散是主要原因；根據實驗結果及實驗中出現的問題，對下一步工作提出兩個改進的方案：一是通過在si襯底中注入適量h ~ + / he ~ +形成納米孔層來阻斷ge擴散通路，二是可以通過控製表面氧化來調節安止額士淤丈撈要表面sige層中的ge組分，從而部分解決sige -
The alloys, which were cold - worked followed by recrystallization annealing, display cyclic softening in the range of low strain because the cyclic stress - strain curve lies below the monotonic stress - strain curve, and show cyclic hardening in the range of high strain because the cyclic stress - strain curve lies above the monotonic stress - strain curve
在低應變范圍，冷加工后經再結晶退火處理的錯合金的循環應力一應變曲線位於單調拉伸曲線的下方，表現為循環軟化;在高應變范圍則位於單調拉伸曲線的上方，表現為循環硬化。 -
Standard test method for annealing point and strain point of glass by beam bending
用梁彎曲法測定玻璃的軟化點和應變點的標準試驗方法 -
Glass - viscosity and viscometric fixed points - part 7 : determination of annealing point and strain point by beam bending iso 7884 - 7 : 1987
玻璃.粘度和粘度固定點.第7部分:射線束彎曲法測定退 -
Viscosity and viscometric fixed points of glass - method for the determination of annealing point and strain point by beam bending
玻璃粘度和測定粘度固定點.第7部分:採用射束彎曲法對退火點和應力點的測定方法 -
The formation of a new set of strain - free grains within a previously cold - worked material ; normally an annealing heat treatment is necessary
在冷塑性變形材料的內部生成等軸狀新晶粒的過程叫再結晶，通常發生於再結晶退火熱處理過程中。 -
Test method for annealing point and strain point of glass by fiber elongation
用纖維伸長法測定玻璃的軟化點和應變點的試驗方法 -
Viscosity and viscometric fixed points of glass - part 2 : determination of annealing point and strain point by fiber elongation
玻璃的粘度和測粘固定點.第2部分:通過纖維伸長度測定退火溫度和應變點 -
Determination of annealing point and strain point of glass
玻璃的退火溫度和應變溫度的測定
分享友人