strain-stress test 中文意思是什麼
strain-stress test
解釋
應力應變試驗-
The main contents are as follows. ( 1 ) filter cloth and the surrounding soil mass are taken as an approximate isotropy in horizontal section, the relationship of stress and strain is studied, the anisotropy is fully considered, the constitutive model of filter cloth reinforcement fly - ash compound is obtained, it is tested with numerous indoor experiments. ( 2 ) the permeable coefficient is introduced into the constitutive relationship of soil mass with relevant seepage theory ( kozeny - carman experience formula ). the test of filter cloth depositing hi the condition of long term seepage flow is done hi the dissertation, the varying regular of permeable coefficient without pressure is presented
本文首先對國內外的研究現狀作了回顧和總結，然後主要針對土工織物加筋粉煤灰復合體的本構關系和計算理論進行研究，主要內容有： （ 1 ）將土工織物和周圍土體視為一種近似的彈性非線性橫觀各向同性體，研究它的應力應變關系，充分考慮它的各向異性，得到土工織物加筋粉煤灰復合體的本構模型，然後通過大量室內試驗進行分析驗證； （ 2 ）引入有關滲流理論，即柯茲尼-卡爾曼（ kozeny - carman ）經驗公式，將滲透系數引進到土體本構關系中。 -
For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels
為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。 -
Back - analysis method and computing program of damage parameters by the curve of stress - strain by uniaxial tension and compression test was made out. 5. by the damage evolving relation proposed the flexural process of the trisection specimens of wet - sieved and fully - graded concrete was numerically simulation
5 .根據本文提出的損傷模型和損傷參量演化關系，分別對濕篩混凝土和全級配混凝土試件進行了三分點加載數值模擬。 -
While cyclic deformation experiment under constant strain control is performed in 400, the material shows the continuous hardening until cyclic invalidation. ( 3 ) back stress attained by kwl " s method is used to analyse the bauschinger effect during an incremental step cyclic test and cyclic deformation test under constant strain control, it is shown that back stress increases with increasing plastic strain and the numbers of cycle, and the back stress is uniform, regardless of tension or compression conditions. ( 4 ) as far as recrystallized zircaloy - 4 plate is concerned, the back stress in transverse direction is higher than that in rolling direction due to the higher schmid factor in rolling direction
對于再結晶狀態的zr一4合金板材試樣來說， t方向（橫向）試樣的背應力要高於r方向（軋制方向）的背應力，原因在於r方向的schmid因子高於t方向的schmid因子; 400下， zr一4合金的背應力要明顯低於室溫下的背應力;含氫200pg / g的zr一4合金的背應力大小與無滲氫的zr一4合金背應力相比，無明顯區別;固溶處理后， zr一4合金的背應力大小發生了變化，在較高塑性應變下，背應力均高於固溶處理前的背應力。 -
So it is very important to understand the cyclic deformation behavior of zircaloy - 4. in this paper, bauschinger effect of zircaloy - 4 with different metallurgical state at room temperature and 400 ? is investigated in an incremental step test and cyclic deformation test under constant strain control. bauschinger effect during cyclic deformation is described by using back stress, which is mainly responsible for bauschinger effect ; back stress is attained by using kwl " s method
本文採用單試樣逐級加載循環變形和恆應變幅循環變形試驗，研究了不同冶金狀態、溫度、氫以及固溶處理下的zr - 4合金的bauschinger效應現象；種種結果表明，影響bauschinger效應的主要因素是背應力；本文正是從背應力的角度來分析各種狀態下zr - 4合金的bauschinger效應現象；背應力的計算主要通過使用kwl方法而獲得。 -
Standard test method for thick - adherend metal lap - shear joints for determination of the stress - strain behavior of adhesives in shear by tension loading
拉伸載荷法測定剪切中膠粘劑應力-應變性能用厚被粘物金屬搭接-剪切接頭的標準試驗方法 -
It is indicated in the test that the influence of loading to strain in the grout was about in the range of 5 ~ 6m, and very weak beyond 4m. the distributions of strain and bond stress in the grout are attenuated in the minus exponential rule
試驗結果表明，加載對錨固段內的應變影響范圍大致在5 6m左右， 4m以外很微弱；錨固段注漿體內的應變與粘結應力分佈按照負指數規律衰減。 -
In this test, a special bolt - jack is used to exent of prestressing force to brace angles as the whole structure is under dead - load. in this state brace angles withstand partly load before twice - load and the stress and strain of concrete are decreased. in this way the aim of removal of load and strengthening can be reached
本試驗中採用專用螺栓千斤頂在恆定荷載水平下對混凝土柱角鋼撐桿施加預壓應力，使外包角鋼在二次受力前即分擔部分荷載，使混凝土應力水平和應變水平降低，達到卸載與加固同步進行的目的。 -
Geotechnic centrifuge model test technique utilizes the equivalence between centrifugal force field and gravitational field ; model dimension dwindles into 1 / n times of prototype " s, but the body force on the model increases n times. the strain and stress of model is equal to prototype " s, but the displacement of prototype is n times of model " s
土工離心模型試驗技術利用離心力場和重力場等效性，將模型尺寸縮小到原型尺寸的1 / n ，同時作用在模型上的體積力增大n倍，這時，模型中各點的應力、應變與原型中對應點的應力、應變相等，原型和模型對應點的位移成n倍關系。 -
Centered on the investigation on the evolvement of permeability as well as the coupling action between seepage and stress, the following work is carried out : 1. a further examination is given to classical biot seepage theory to discover the basic assumption to form the coupling seepage equation, and discuss the variety of coupling equations between seepage and stress and their adaptabilities. the physical meanings, adaptability, testing method of seepage parameters used in equation of continuum are analyzed based on the experimental investigations on complete relationship between stress, strain and permeability of rock and engineering test on permeability of rock at different depth
本文圍繞巖石破裂過程中滲透性的演化規律及其滲流-應力耦合作用機理這一課題，開展以下方面的研究工作: 1 .對經典biot滲流力學做了進一步的考察，揭示建立耦合滲流方程的主要假設，討論了各種滲流與應力耦合方程及數學模型的適用條件，通過巖石應力應變-滲透率全過程實驗研究和不同深度巖體滲透率工程試驗研究，分析了連續介質模型耦合滲流方程參數的物理意義、適用性、測試方法。 -
The first stage is primary slip then followed by secondary slip ; the last stage is due to dislocation passing the slips. the cyclic stress strain ( css ) curve exhibits a stronger hardening occurred in cyclic plastic deformation than that in tensile test
建立了拉伸和應變疲勞的有限元模型，使用基於晶體滑移模型的數值方法，對晶體內部滑移系的啟動以及滑移繫上的分解切應變、切應力這些無法試驗觀測的變量進行計算，分析它們對晶體塑性變形的不同影響。 -
The experimental results is shown as followings : ( 1 ) the cyclic flow stress - strain curves in an incremental step test could be expressed as the power law relation : ( 2 ) when the strain amplitude is lower during cyclic deformation tests under constant strain control, softening firstly appears, then gradually hardens with the increasing numbers of cycle ; when the strain amplitude is higher, hardening firstly appears, then gradually softens
試驗結果表明： （ 1 ）循環流變應力與應變的相互關系曲線均符合冪律關系式： （ 2 ）在室溫下進行恆應變幅循環變形過程中，當所控制的應變幅較小時，該材料首先出現循環軟化，之後隨循環周次的增加直至循環失效前該材料出現了硬化現象。當應變幅較大時，該材料開始出現硬化，然後隨循環周次的增加才出現軟化。 -
The triaxial shear test of the original loess is carried out and the ct scanning is ongoing at the same time. combining images and data of the ct scanning with the stress - strain curve, the course of soften dehiscence damage and harden yield damage is explained by means of damage theory
進行了原狀黃土的三軸剪切試驗過程中的ct掃描，結合ct圖像、數據與應力應變曲線，利用損傷理論方法解釋了軟化開裂破壞和硬化屈服破壞過程。 -
The existed material fatigue performance test curves are dealt with and analyzed, and the non - dimensional stress - strain curve, tangent modulus factor curve and fatigue life curve are drawn based on the experiment data, and these three non - dimensional parameter curves are used to find the inherent rules that the test curves can be replaced each other to some extent. it can be concluded that if the common character and system error of these materials are found, the test curve of a certain material can be used for reference by another material. this is a simple approach about fatigue life estimate and is engineering practical
對已有的材料力學疲勞性能試驗曲線進行分析整理，利用試驗數據繪制了相對應力應變曲線、切線模量因子曲線和疲勞壽命曲線，利用這三種無量綱參數曲線發現了其中存在的規律性，即在某種程度上實驗曲線可以互相取代，並用試驗數據對此進行了討論，並由此推斷，如果找出材料彼此的共性或彼此之間的系統誤差就可以將一種材料的試驗曲線供其它材料參考使用，這是一種估算材料的疲勞壽命的簡便方法，對工程而言具有實用性。 -
In this paper, a numerical simulation is conducted, which is based on the test data of the model experiment of sloping ground with the help of the marc program. when the bearing capacity characters of level ground and the foundations adjacent to or above slopes are analyzed, the effect is considered, which includes deformation moduli, density, poisson ratio, angle of internal friction, stress - strain relationship, slope angle, relative distance from the edge of slopes and relative depth of footings
本文利用斜坡地基模型試驗的試驗數據，用marc軟體進行了斜坡地基模型試驗的數值模擬，分析了平地地基、臨坡地基和斜坡地基的承載力特性，研究了變形模量、容重、泊松比、內摩擦角、應力應變特性、斜坡坡度、基礎的相對坡頂距及其相對埋深等因素對斜坡地基承載力性能的影響。 -
Saturated sand are testes in the laboratory under the undrained cyclic loading condition with static - dynamic dual purpose triaxial compression test apparatus, which is designed under the cooperation of hohai university and marui co. ltd japan. the results indicate that the stress path approaches from a initial stress point to the failure lines as cyclic loading goes on, and eventually converges on a certain limiting stress path in the vicinity of the failure lines. the stress - strain curve, however, does not converge on a closed hystersis loop ; the shear strain rapidly increases in looser sand or gradually and continually increases in denser sand
利用河海大學與日本圓井株式會社共同研製的新型的多功能靜動三軸儀進行了飽和砂土循環扭剪不排水試驗，研究表明，對于松砂，剪應變幅度快速地由微小增加到百分之幾甚至百分之十幾，對于緊砂，剪應變幅度逐漸地由微小增加到百分之幾甚至百分之十幾；經試驗初步研究表明用初始有效平均正應力歸一化的有效應力路徑很好的一致性。 -
A developed measuring system and test method of green sand properties are introduced. by means of measuring the standard molding sand specimens, the dynamic curves of stress - strain can be quickly and accurately plotted out and several parameters, which represent the characteristics of molding sand, can be tested during the process of compressive deformation. in this brand new method of property measurement two new concepts of viscoelastic parameter and plastic deformation threshold are put forward
介紹了一種研製的型砂性能檢測系統與測試方法，通過對標準砂樣的測試，能迅速、準確地測得砂樣受載過程中的應力應變的動態關系曲線及反映型砂本質特徵的幾項性能參數，這是型砂性能檢測領域中的新探索，其中型砂粘彈性指標及塑性變形臨界值乃是型砂性能方面的新概念。 -
The stress " ce " and the strain " cc " of the high - strength concrete confined with high - strength continue compound spiral hoops is advanced according to the test value and the theory in the document [ 60 ]
結合試驗數據和文獻中的理論，提出了高強連續復合螺旋箍筋約束高強混凝土的應力，乙和應變~ （ cc ） 。 -
The dynamic parameters of the asphalt concrete can be obtained through dynamic triaxial test, combined with the cunli chen ' s studying results, discovering that the dynamic stress - strain relationship obeys the hyperbolic model well, and t he maximum dynamic modulus edmax and the maximum shear modulus gdmax increasing along with the decreasing of the temperature and the increasing of consolidation ratio kc
通過振動三軸試驗獲得瀝青混凝土材料的動力參數，並結合西安理工大學陳存禮老師的研究成果。發現動應力與動應變的關系較好地符合雙曲線規律，最大動模量e _ （ dmax ）和最大剪切模量g _ （ dmax ）隨著溫度的降低、圍壓和固結比kc的增大而增大。 -
The damage parameter versus fatigue life figures, which were plotted based on the stress - strain analysis and test results, could be used to predict the fatigue lives of the composite with different winding angles
根據雙軸載荷條件下管狀試樣的應力-應變分析及雙軸疲勞實驗結果，繪制出了基於臨界平面的多軸損傷參量與疲勞壽命關系圖，可對不同纏繞角的復合材料疲勞壽命進行預測。
分享友人