stress-deformation curve 中文意思是什麼
stress-deformation curve
解釋
應力形變曲線- stress : n 1 壓力，壓迫，緊迫，緊張。2 【語音】重音；重讀；【詩】揚音；語勢，著重點。3 重要（性），重點，...
- deformation : 變形,走樣
- curve : n 1 曲線；彎曲；彎曲物。2 曲線規 （＝French curve）；【機械工程】曲線板；【棒球】曲線球；【統計學...
-
The first stage is primary slip then followed by secondary slip ; the last stage is due to dislocation passing the slips. the cyclic stress strain ( css ) curve exhibits a stronger hardening occurred in cyclic plastic deformation than that in tensile test
建立了拉伸和應變疲勞的有限元模型，使用基於晶體滑移模型的數值方法，對晶體內部滑移系的啟動以及滑移繫上的分解切應變、切應力這些無法試驗觀測的變量進行計算，分析它們對晶體塑性變形的不同影響。 -
Based on the creep experimental curve, the creep deformation law of silty soft clay of the first marine layer and its constitutive relationship among stress - strain - time is studied in this paper
本文在蠕變試驗曲線的基礎上，研究了天津市第一海相層淤泥質粉質粘土的蠕變變形規律，得出應力、應變、時間三者之間的本構關系。 -
Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape
摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。 -
In order to establish the nonlinear elastic model of qi loess, the hump curve was used to stimulate both the softening stress - strain curve and the volume deformation curve
對軟化型應力應變曲線提出用駝峰曲線模擬，對體變曲線也提出用能反映剪脹的駝峰曲線模擬，建立了q1黃土的非線性彈性k 、 g模型。 -
Abstract : based on the hypotheses of three - piece straightening curve. it isverified that the method for using little deformation condition was true with accurate solution of three - piece straightening curve. the mechanics behavior of slab was analyzed in regard to the creep properties of high temperature slab. the results show that the strain, the strain velocity and the stress varied so smoothly that the inner crack was prevented. technical renovation is carried on by adjusting the displacement of rolls and by using the accurate solution of three - piece straightening curve
文摘:基於三段矯直曲線應變速率的假設，通過計算三段矯直曲線的精確解，驗證了使用小變形條件的正確性;考慮高溫鑄坯蠕變性能，對鑄坯的力學行為進行了分析，得出了使用三段矯直曲線方法，鑄坯應變速率、應力及應變在矯直區內變化較為平緩，可有效避免鑄坯內裂紋的形成;使用本文三段矯直曲線精確解，調整輥列位置，可進行連鑄機的在線技術改造。 -
Based on the constitutive relationship coupled microstructure evolution, 3d - fe simulation of isothermal forging process of tc6 titanium alloy disc is performed dealing with different deformation temperature, punch velocity and shear factor of friction, effect of process parameters on equivalent strain, equivalent stress and grain size is calculated, and load - displacement curve is calculated
本文基於微觀組織演變的本構關系模型，對不同變形溫度、凸模速度和摩擦條件下鈦合金盤的等溫鍛造過程進行了三維數值模擬，研究了變形工藝參數對等效應變、等效應力和晶粒尺寸的影響，計算了各變形條件下的位移?載荷曲線。 -
Elastomer is a class of polymers whose deformation displayed by strain - stress curve is totally elastic, i. e., large recoverable strains produced at low stress levels
彈性體是聚合物的一個種類，它的應力應變曲線表明其變形是完全彈性的，即很低的應力變化就會產生很大的可回復應變。 -
It ' s we1l known that the windshield material is an organic material. it shows visco - plastic behavior which is that the stress - strain curve, the yield stress and the limited stfess varied with the material deformation rate
眾所周知，風擋材料為有機材料，一方面呈現出粘彈塑性特性，即材料的應力應變曲線、屈服應力、破壞應力都隨著材料變形速率的變化而變化。
分享友人