structural foam 中文意思是什麼

structural foam 解釋
構造泡沫
  • structural : adj. 構造上的，結構上的，組織上的。adv. -ly
  • foam : n 1 〈只用單數〉泡沫；（馬等的）涎沫[大汗]。2 泡沫材料，泡沫狀物，泡沫橡皮；泡沫塑料。3 〈詩〉海...
  1. Therefore, the purpose of this thesis is to look for a suitable preparing process for 3 - tcp with their micro - construction controlled more easily and the porosity rate and strength uniform. this paper created a new preparing method of porous ceramics, i. e. foam gel - casting technique, which integrated foam technique in porous ceramics preparing and gel - casting technique in structural ceramics preparing was applied to improve the preparing technique of porous p - tcp bioceramics in order to prepare ceramics bodies with high body intensity, controllable porosity and easily machining performance

    因此，本論文努力尋求一種適合於- tcp多孔陶瓷的制備工藝，使其微觀結構易於調節控制，空隙率和強度達到平衡同一。在實驗中，結合了制備多孔陶瓷常用的發泡法和結構陶瓷制備中的注凝法，創新設計了一種新的多孔陶瓷成型方法? ?泡沫注凝法，對多孔- tcp生物陶瓷的成型工藝加以改進，制備出高強度、氣孔率可控以及易加工的陶瓷坯體。
  2. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  3. Standard specification for rigid foam for use in structural sandwich panel cores

    結構夾層板芯板用硬質泡沫塑料標準規范
  4. The compound tray researched in this paper consists of dual - flow tray and 50 - 1 ^ omm high structural packing which is directly put under the dual - flow tray. it has three mass transfer sections that is the foam section on the tray, the film section in the packing layer and the shower section under the packing, so it has very high mass transfer efficiency

    本文研究的復合塔板是在穿流篩板之下緊貼一層50 150mm的規整填料所構成，它有三個傳質區，即塔板上的泡沫區、填料層內的液膜區以及填料層下的淋降區，因此，具有很高的傳質效率。
  5. By changing the contents of blowing agent and the inner size and changing the density distribution of structural polyurethane foam, the influences of the inner structure on the properties of gradient density polyurethane foam were investigated

    摘要通過改變發泡劑用量和採用不同密度泡沫組合，來改變聚氨酯結構泡沫整體的密度分佈，研究了梯度密度聚氨酯泡沫塑料的性能。
分享友人
分享到 Line

分享到臉書