supporting bracket 中文意思是什麼

supporting bracket 解釋
支承架
  • supporting : adj. 1. 起支持[支撐]作用的。2. 協助[配合、支援]的；起配角作用的。3. 可提供證據的，證實的。
  • bracket : n 1 【建築】斗拱，托架，角撐架；【機械工程】支架，懸臂，座；（墻上裝的）煤氣燈嘴[電燈座]。2 〈pl ...
  1. The top end bracket shall be fitted with a stainless steel lifting bail and shall be capable of supporting the combined weight of the pump and motor

    頂部尾軸承架應該配置不銹鋼吊環，應該能夠支撐泵和電機的總重量的壓力。
  2. The top end bracket shall be fitted with a lifting bail and shall be capable of supporting four ( 4 ) times the combined weight of the pump and motor

    頂部尾軸承架應該配置吊環，應該能夠支撐泵和電機的總重量四（ 4 ）倍的壓力。
  3. The whole system is supported by the main jack arrangement when concreting, placed at the front supporting bracket and the ( rear ) suspension gallows ? or on supporting brackets only at the start and expansion joint spans

    整個系統在混凝土澆注過程中由前牛腿及（后）吊架上主千斤頂系統支撐，在起始段和伸縮縫處則在前後牛腿處支撐。
  4. 2. detailed introductions are given for the design scheme and engineering situations. 3. the construction design, construction scheme and construction technology of ballastless embedded sleeper track are researched in combining with the constructing of the ballastless track on shahe bridge inside b26 - 1 section on qin - shen railway. the design, application and construction measure for the adjustable up - supporting bracket for track panel are particularly described and expatiated

    結合秦沈客運專線b26 - 1標段內沙河無碴軌道實際施工情況，對長枕埋入式無碴軌道的總體施工安排、施工方案以及施工工藝進行了研究，同時重點對長枕埋入式無碴軌道的上承式可調式軌排支撐托架的設計、使用和施工測量控制進行了細致地說明和闡述。
  5. The winding - pipe machine principal - axis magnetism supporting system is a typically electromechanical and electromagnetical product with some main parts : electromagnet system, electromagnet bracket system, etc. the study of the winding - pipe machine principal - axis magnetism supporting system concerns the intercross of many disciplines, such as mechanism, material, electronic engineering, heat engineering, computer, and so on

    它主要有由電磁鐵機構與電磁鐵支架機構等組成，是一種典型的機電磁一體化產品，其研究涉及到機械、材料、電工、熱工、計算機等多學科的交叉。本論文對管絞機磁性支承系統涉及的兩大關鍵技術? ?電磁場設計與機械結構設計及其相關技術進行了系統的理論分析與模擬研究。
  6. Each supporting metal bracket must have at least three anchor bolts installed

    支撐角架最少要用三顆系穩螺絲
  7. Pc especially can be used i n manufacturing the foundation, bed supporting bracket. in experi ment, we are studying with using stimulating machine bed and taki ng the finite element method to stimulate it, results of experiment and stimulating prove that this kind of material is good in machine engineering

    特別適用來製造機床底座、床身、支架等基礎件件。在實驗中，我們用模擬機床床身進行研究，並用有限元軟體進行了數值模擬，實驗及擬和結果證明其應用的價值。
  8. In chapter 2, the mechanical bracket supporting system physical model is establish, and flexibility and reversed force are calculated, simultaneity, some technique needs are brought forward

    第二章對原機械托輥支承機構進行了物理建模及靜反力和撓度分析，對后續設計工作提出了一些技術要求。
  9. Each supporting bracket consists of two halves, stressed together by means of tension bars

    每對牛腿由高強螺紋筋張拉在一起。
  10. It provides steady lifting with low noise, and is equipped with lifting brackets, anti - fall supporting protection, stopping protection against wire fracture, limiting device for maximum load, control device for maximum lifting height and fixing device for the turning angle of the bracket arm

    升降平穩、噪音低，並設有舉升托架、防跌落支承保險、鋼索斷裂制動保險；最大負荷限定裝置和托臂回轉角度鎖定裝置。
  11. Because slts owns too many parts and complex supporting conditions, and invalidation of few parts or nodes does not have significant effect for structural bearing capacity, research orientation is transferred to structural support system in chapter 4 of the thesis. limited loading capacity and safety index of steel bracket of slts are calculated and analyzed for providing theoretic upper limit to safe operation of support system

    由於網架結構的桿件眾多，結構支撐條件復雜，少數桿件或節點的破壞對于結構的正常承載無顯著影響，本文在第四章將研究方向轉向網架結構的支撐體系，計算分析網架結構支撐鋼牛腿的極限承載能力和安全儲備，為支撐系統的正常工作提供一個理論上限。
分享友人
分享到 Line

分享到臉書