switch panel 中文意思是什麼

switch panel 解釋
開關板；電掣箱
  • switch : n 1 （樹上折下的）細樹枝；軟鞭子；鞭打。2 假發；（尾巴上的）毛簇。3 〈美國〉【鐵道】道岔扳子，軌...
  • panel : n 1 面，板；【建築】四分板，門窗材，幅板，板條；嵌板；鑲板；方格；（木工）線板；【繪畫】（代替畫...
  1. If bath king has been used for a long time, there will be feculence on the switch panel. when clear it, cut off power at first to make sure power off. and then use dishcloth with a little neutral detergent to rub it till the feculence is removed

    用戶長期使用浴霸，開關面板沾有污漬，在清理這些污漬時，應先切斷電源（零線和相線） ，並在確認沒電的情況下，用沾有少量中性清潔劑的抹布擦試，待污漬擦去后，再用清潔干布擦乾。
  2. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  3. Pre - drilled hole at panel ; led indicator hole 4mm dia. toggle switch hole

    預鉆孔面板; led燈孔4mm搖頭電源10mm
  4. This system has two modes : automatic, manual. under the automatic condition, when the system detect that there is fire happening, the system will turn off blower, switch on valve and pump, and extinguish the fire if no people deal with the fire in the set time after the audible and light. under the manual condition, the operator can extinguish fire in the appointed area by the button in the main controlling panel or the manual button box ( locale )

    在自動方案運行情況下，當系統檢測到有火災情況發生時，在發出聲、光報警后的一定時間，如果無人干預，則系統自動執行關閉風機、開閥、開泵，對火災區域進行水霧滅火；而在執行手動方案情況下，操作人員可以通過操作主控制屏上的按鈕或手動按鈕（現場）來對指定的區域進行噴灑滅火。
  5. This machine is used for straight - line bevel cutting and bevel grinding and polishing for flat glass, in certain condition, it can be also used in bevel cuttig, bevel grinding and polishing for soft stone panel. the contrilling system adopts plc, it can accomplish automatic grinding cutting after entering processing parameter, convery speed adopts speed adjustment of fre quency conversion, direct drive of wheel head motor, all motions for joining in parameter adjustment completely adopt straight - rolling guide - track with front beam and wheel head lifting lntegrally. the transmission of input and output adopts synchronization tooth belt and photo - electricity switch positioning, and position limitation of two pass is much more reliable

    Sxm371pa型玻璃直線斜邊磨邊機是用於玻璃直線斜邊斜切，斜磨及光拋的專用設備，在一定條件下也可以用於軟石板材的斜切斜磨及拋光。控制系統採用plc控制。輸入加工參數后可自動完成磨削傳送速度採用變頻調速，磨頭電機直接傳動，所有加工參數調整運動副全部採用直線滾動導軌，前梁與磨頭整體升降，輸入輸出傳送採用同步形帶，光電開光定位，雙行程限位更安全可靠。
  6. There is a switch board control panel, distribution box mounted on the wall

    在墻上裝有一個開關板控制盤配電箱
  7. Control switch in one control panel easy operation and height capacity

    電動式印刷部離合裝置，方便省時，提高生產力，適用少量多樣化訂單。
  8. When a key switch at the main floor or on the supervisory panel is turn on, all calls are cancelled, the car is immediately called to specified rescues floor and parks with door opened

    當基站或監視屏上的專用要是轉動到至消防狀態，或火災傳感器被啟動，所有轉換均被取消，電梯立刻駛往指定救援層展停靠，並自動打開門。
  9. Guangzhou hongpeng electronic co. ltd is established in 2001. we are an professional enterprises to produce backlight, brane switch, faceplate and touch panel

    廣州宏鵬電子有限公司成立於2001年，是家集生產背光源、薄膜開關、面板、觸摸屏為一體的企業。
  10. There is a switch board ( control panel, distribution box ) mounted on the wall

    在墻上裝有一個開關板（控制盤、配電箱） 。
  11. Kunshan fu printing electronic co, . ltd was set up in 2004, and we produce the nameplates, control panel and membrane switch, all the process are completed in our factory to meet the requirements for the quality and delivery

    崑山富展電子科技有限公司成立於2004年，主營高端銘板，控制面板，薄膜開關等，一貫製程在廠內完成，確保品質及交期滿意客戶。
  12. 08. switch number control panel

    08 .撥碼式面板控制
  13. Relying on years of researching of electric power, accumulated manufacturing experience, and affluent economic technological power, the enterprise is capable of product pgl, ggd, gcs, gck low voltage power distributing panel, xgn2 - 12, hxgn15a - 12 high voltage switch cabinet, xbz1, xbj1 box - type transformer substation and zw8 - 12 630 - 20 outdoor high voltage vacuum breaker, totally 6 series and 200 more varieties. the products are a great contribution to the social economic development and have been recognized and praised by vast customers

    企業憑借多年的電氣成套研製生產經驗和雄厚的經濟技術力量，生產pgl ggd gcs gck型低壓配電屏xgn2 - 12 hxgn15a - 12型高壓開關櫃xbz1 xbj1型箱式變電站及zw8 - 12 630 - 20型戶外高壓真空斷路器等6大系列200多種品種，為社會經濟發展提供可靠的產品和服務，得到廣大客戶的認可和贊譽。
  14. Control panel : computer, monitor, fan, switch of stereo, sound volume and tuning

    控制面板:主機，顯示器，風扇，音響開關，音量，音調調諧。
  15. The 80c196kc single chip microprocessor, electronic switch array, cpld, large capacity ram were integrated into the interface card. the detection operation is intelligent and automatic. the control software and the virtual instrument panel were designed in visual c + +, different messages were sent through serial port

    在檢測系統中設計了具有高速并行數據採集及處理功能的介面卡，介面卡上採用80c196kc單片機、電子開關陣列、大規模門陣列（ cpld ） 、大容量存儲器等器件，實現了智能化、自動化檢測；在微機軟體設計上，運用visualc + +語言編制了虛擬儀器面板程序和控製程序，通過微機串口向單片機發送各種信息。
  16. If the main switch selector is set to l ( lock ), the power will be completely cut off. the lcd panel and the viewfinder display will not operate

    如主選擇開關設置在（鎖定） ，電池將完全斷開，液晶顯示屏和取景器中的顯示將消失。
  17. Selecting one of the function modes is done from the control panel of local cabinet ( near the furnace and the loading area ) by a selecting switch

    用選擇開關從本地控制櫃（爐和裝載區域附近）的控制面板上選擇其中一個功能模式。
  18. Technique characteristics : incorporate transform with control, reduce assistant equipment ; can setup parameters through panel key in the work field, simplify for operating ; multi - switch quantity node output, fulfil the requirement under commonly controlling work - field ; all the configured parameter is saved in eerom ; adopt rs232 and rs485 communication mode

    技術特點：集變送、控制為一體，減少輔助設備；現場即可通過面板按鍵設置參數，簡單易操作；多點開關量輸出，滿足一般控制現場；所有設置參數都存儲在非易失的存儲器中；採用rs232 、 rs485通訊方式。
  19. Sgk - b250 plastic pipe belling machine attribute semiautomatic opportunities for the single - use. such models use infrared heating, molding method adopts expand the headers to finalize the design, orifice size precise shape. the control panel don ' t have the conversion switch to control over the type of solvent for expansion socket ( vertical ) and ring - for flexibility expansion socket ( r ). expanding way is very easy choice and technics adaptability is strong, the main electrical control components are imported, system performance is stable and reliable

    B250塑料硬管擴口機，屬半自動型作單機使用，擴管時管材由人工搬至擴管工位：這種機型採用紅外線加熱方式：成型方式均採用擴管頭定型方式，管口成型尺寸準確：該機型在控制面板上沒有擴溶劑型承插口（直口）和擴彈性密封圈型承插口（ r口）的轉換開關，擴管方式選擇十分方便，工藝適應性強：主要的電器控制元件均採用進口元件，系統性能穩定可靠。
  20. In the j2ee hierarchy to open its editor and switch to the jms tab to display the websphere jms provider options panel

    ，打開編輯程序並切換到jms選項卡以顯示websphere jms provider options面板。
分享友人
分享到 Line

分享到臉書