tappet 中文意思是什麼

tappet 解釋
n. 名詞 【機械工程】挺桿。

  1. Influence of temperature on cam - tappet lubrication in an internal combustion engine

    挺柱潤滑的影響研究
  2. Wrenches, box, angled, open end, combination, flare nut, and tappet inch series

    組合開端套筒扳手和聯接螺母
  3. Analysis and protective measures of tappet rod wear on lycoming engine

    萊康明發動機挺桿磨損成因分析與防範措施
  4. Before design cam, the tappet displacement curve has to be design

    在設計凸輪之前，首先進行挺柱升程曲線的設計。
  5. Wrenches, box, angled, open end, combination, flare nut and tappet metric series

    斜開口端和套筒組合式螺帽和梃桿扳手
  6. Tappet noise valve knock

    氣門挺桿發響
  7. Ustment of valve tappet

    閥門挺桿調整
  8. Valve tappet ustment

    閥挺桿調整
  9. Tappet rod complement

    挺桿總成
  10. Valve tappet guide

    閥挺桿導承
  11. According to the tappet displacement curve, the design of cam profile can be carried out by " reversal method " theory

    根據得到的挺柱升程曲線，利用「反轉法」的原理進行凸輪輪廓曲線的設計。
  12. The paper ' s design mainly includes two parts. fist part is the tappet displacement curve ' s design, and many dynamics calculation has to be done based on the dynamic design. second part is to design cam profile curve

    本文的設計主要包括兩大部分，第一部分為挺柱升程曲線的設計，按照動態設計要進行大量的動力學計算，第二部分是凸輪輪廓曲線的設計。
  13. While according to dynamics correction method, the valve displacement curve has to be design, which can be acquired by boundary condition and calculation method. then by dynamics analysis, the tappet displacement curve equation can be obtained based on the dynamics differential equation. thus, the design of cam profile can be carried out based on the tappet displacement curve equation

    按照動態設計的動力學修正方法進行設計時，又得先進行氣門升程曲線的設計，利用一定的邊界條件和計算方法得到氣門確定的運動規律，再通過動力學分析，根據建立的動力學微分方程，經過計算得到挺柱的升程曲線方程，至此，就可以根據挺柱的升程曲線進行凸輪輪廓曲線的設計。
  14. According to the characteristics of the overhead camshaft valve train, the author thoroughly analyzed the kinematics and dynamics concerned in the design of valve train cam profile. the results illuminate the influence of valve timing, ample factor as well as the contact stress between cam and tappet on the design of cam profile

    根據頂置凸輪軸式配氣機構的特點，文章深入分析了在配氣凸輪型線設計中必須涉及的運動學及動力學問題，說明了配氣定時、豐滿系數及凸輪與挺柱間接觸應力對凸輪型線設計的影響。
  15. Tappet roller pin

    挺桿滾輪銷
  16. Tappet rod for valve

    氣門挺桿
  17. The last part of this paper treated the results with the assistance of spline function and nth - degree harmonics cam approximate. thus, the new function of tappet, speed and accelerated speed was gained and the whole designing process was completed

    文章的最後部分分別用樣條函數方法和n次諧波凸輪逼近方法對計算結果進行處理，得出新的從動件升程、速度和加速度的解析式，從而完成整個設計過程。
  18. Wrenches, box, angled, open end, combination, flare nut and tappet metric series ; errata

    錐形螺母和螺桿組合成的開口斜角開口扳手.勘誤
分享友人
分享到 Line

分享到臉書